RedMaxメーカーBC2200Eの使用説明書/サービス説明書
ページ先へ移動 of 24
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING OWNER / OPERA T OR MANUAL TRIMMERS / STICK EDGERS 5850-93110 (9809) IMPORTANT : Before operating your RedMax product, read this manual carefully and completely.
.
Thank you for choosing a RedMax trimmer / stick edger . This manual will provide you with full understanding of the necessary instructions for assembly , operation and maintenance of the equipment. Please read this manual carefully before starting operation.
FOR SAFE OPERA TION ■ KNOW YOUR UNIT 1. Read this Owner's Manual carefully until you completely understand and can follow all safety rules, precautions, and operating instructions before operating the unit. 2. Restrict your unit to users who understand and follow all safety rules, precautions, and operating instructions found in this manual.
■ HE2200LDC 1. Install the blade guard to the gear case with the provided 3 screws. 2. Place the blade between the cutter holders (A) and (B) while locking the gear shaft by putting the bar , one of the tools provided, through the key holes on the holder(A) and the gearcase.
FUEL The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. When RedMax oil is not available, use an anti-oxidant added quality oil formulated for air-cooled 2-cycle engine use.
■ STARTING ENGINE Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 1. Press the primer bulb until fuel flows out in the clear tube (5 to 7 times). Lace the choke lever in the full choke position.
■ LINE HEAD USAGE • HOW TO USE 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal Injury. 2. Keep the debris guard attached in place at all times when the unit is operated.
OPERA TION ■ METAL BLADE USAGE NOTE : Do not use the Metal Cutting Blade for model BT2200LDC and BC2200E • Always cut by guiding the head from your right to left. • When mowing a wide area, start working from the left side to avoid interference of cut grass.
g. Cut only from your right to your left. h. Keep your path of advance clear of material that has been cut and other debris. 3. How you can maintain the best control: a. Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce.
I . Bump head for BT2200LDC and BC2200E ■ REPLACING TRIMMING LINE To refill a new trimming line either ; A : Install the prewound reel #153577 or B : Rewind the existing reel. For replacement line, use a diameter of .080 in (2.03 mm). The engine may overheat and fail if you use a larger line.
• INSTALLING THE REEL 1. Insert each end of the line through the eyelet on the outer spool. Then pull the end firmly to release the line from the holding slot.
MAINTENANCE 8 11 14 1 2 9 10 12 13 15 THIS SIDE UP THIS SIDE UP WIND LINE 11 .
■ SPARK PLUG Starting failure and mis-firing are often caused by a fouled spark plug. Periodically clean the spark plug and check that the spark gap is within the correct range. For a replacement plug, use Champion RCJ6Y or the equivalent. ■ STORAGE Old fuel left in the carburetor may cause starting failure.
■ BT2200LDC Overall size (LxWxH) ···························································································62.
Fig.1 TRIMMER UNIT FOR BT2200LDC Key# Description Part Number Q'ty P ARTS LIST Fig.1 TRIMMER UNIT FOR BT2200LDC 17 Guard mount screw 153318 1 18 Guard ass'y 683445 1 19 Blade ass'y 6820.
Fig.2 TRIMMER UNIT FOR BC2200E Key# Description Part Number Q'ty Key# Description Part Number Q'ty 1 Straight shaft ass'y ————— 1 2F lex drive shaft ————— 1 3 Thrott.
Fig.3 TRIMMER UNIT FOR BC2200LDC Key# Description Part Number Q'ty Key# Description Part Number Q'ty 1 Straight shaft ass'y ————— 1 2F lex.
Fig.4 STICK EDGER UNIT FOR HE2200LDC Key# Description Part Number Q'ty Key# Description Part Number Q'ty 1 Curved shaft ass'y ————— 1 2F lex drive shaft ————— 1 3 Th.
Fig.5 ENGINE GROUP FOR BT2200LDC. BC2200E. BC2200LDC. HE2200LDC 18 .
Fig.5 ENGINE GROUP FOR BT2200LDC. BC2200E. BC2200LDC.HE2200LDC Key# Description Part Number Q'ty Key# Description Part Number Q'ty 1C ylinder 5850-12110 1 2 Gasket, base 5500-12211 1 3 Bolt .
THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS.
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL BT2200LDC OR BC2200E / BC2200LDC OR HE2200LDC UNIT, KOMATSU ZENOAH AMERICA INC.
KOMA TSU ZENOAH AMERICA INC. 1505 Pavilion Place Suite A Norcross, Georgia 30093 © Printed in the USA.
デバイスRedMax BC2200Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RedMax BC2200Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRedMax BC2200Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RedMax BC2200Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RedMax BC2200Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RedMax BC2200Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRedMax BC2200Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RedMax BC2200Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRedMax BC2200Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。