Remingtonメーカー493の使用説明書/サービス説明書
ページ先へ移動 of 28
REMINGT ON ® Powerdriver Model 493 POWDER ACTUATED TOOL MANUFACTURERS ´ INSTITUTE INC. ™ G 029 ® A N I N D E P E N D E N T L A B O R A T O R Y T E S T I N G F O R P U B L I C S A F E T Y G 028 Read this manual and all labels carefully before operating your powder actuated tool.
2 103500 INDEX Warning: Safety Precautions ............................................................. 3-11 Why A Fastener Holds ......................................................................... 12 Selecting Fasteners and Power Loads .......
3 103500 W arning: Safety Precautions IMPORTANT: Read these operating instructions carefully and com- pletely before trying to operate or service this tool. Improper use of this tool can cause serious injury or death from firing fastener into body or from flying debris.
4 103500 5. Make sure the work area is clean from loose material and debris. 482-12 Safety Precautions POWDER ACTUATED TOOLS IN USE WARNING 482-10 ! 4. Always clear the work area on all sides and post appropriate warning signs on job sites. 1. Never place your hand over the muzzle.
5 103500 Safety Precautions 4 . Never carry or pass a loaded powder actuated tool. Never point a powder actuated tool at anyone. 3. Store powder actuated tool and power load strips in a locked container. Unload tool before storing. Keep power loads of different power levels in separate containers.
6 103500 Safety Precautions 7. An operator taking medication should take extra precautions while handling the tool. Never drink alcoholic beverages or take medications which impair your vision, balance or judgement before using a powder actuated tool.
7 103500 Safety Precautions 3. Never make fastenings in spalled or cracked areas. 2 . Never attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Materials of this type tend to shatter and create hazard from flying particles.
8 103500 TOO THIN WELD 482-40 3/16" MIN 1/2" 1" 482-41 Safety Precautions 7. Do not drive power fasteners into steel base material less then 3/16" thick, within 2" of a weld, within 1/2" of the edge or within 1" of another power fastener.
9 103500 Safety Precautions 2. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Again press the tool firmly against the work surface and pull the trigger.
10 103500 Safety Precautions 3. Never use power loads in firearms. 1 2 3 4 5 6 7 8 9 10 11 12 1 22 L E K C I N B R A S S 482-54 C A L I B E R NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool (See page 13).
11 103500 Safety Precautions 7. Never use common nails or other materials as fasteners. Remington Power Fasteners are manufactured from special steel and heat treated to produce a very hard yet ductile fastener. 8. Never pry a power load out of the strip.
12 103500 Why A Power Fastener Holds WHY A POWER FASTENER HOLDS IN CONCRETE The compression bond of the concrete to the power fastener accounts for the majority of the holding power. The fastener displaces the concrete which tries to return to its original form causing a squeezing effect.
13 103500 Selecting Power Fasteners and Power Loads FASTENING INTO CONCRETE The proper power fastener length can be determined by adding the thickness of the material to be fastened and the amount of fastener that will actually penetrate the con- crete.
14 103500 Operation 1. Grasp barrel assembly and slide forward rapidly until it stops. Push barrel assembly back into tool to the closed position. This sets piston into firing position. 3. Select the proper power level of power load strips. Always insert powder strip loads through bottom of handle.
15 103500 Operation 5. Squeeze trigger to set power fastener. Be sure to keep pressure on tool during this operation. 6. Grasp base plate and slide barrel forward rapidly until it stops. Push base plate back into liner to the closed position. This advances the power load strip and resets the piston for the next fastening.
16 103500 Parts List Key Part No. No. Description Qty. 1 301002 Body 1 2 301034 Trigger Pin 1 3 301906 Advance Bar Assembly (holder,bar,tube) 1 4 301531 Advance Bar Spring 1 5 301533 Trigger 1 6 30101.
17 103500 1 2 3 18 4 5 6 7 8 9 10 11 12 13 14 16 15 17 19 20 21 22 23 24 25 26 27 31 28 30 29 Cleaning and Maintenance Clean tool after each days use. Disassemble and clean the barrel assembly with the wire brush provided with tool. Notice: Do not attempt to clean power load strip channel with wire brush.
18 103500 T ool Disassembly 2. Using thumb, push stop towards rear of tool and remove (see Figure 2). Figure 2 - Removing Stop Stop Figure 3 - Separating Base Plate From Piston Sleeve Piston Sleeve Base Plate 3. Pull barrel assembly out of liner in tool body.
19 103500 6. Remove piston assembly from piston sleeve (see Figure 4). 7. Tilt rear of base plate down. Guide will slide out. REMOVING RUBBER PAD 1. Loosen screw on back of rubber pad with 5mm Allen wrench. 2. Detach rubber pad from top of tool first, then pull entire rubber pad from tool.
20 103500 REMOVING FIRING PIN 1. Remove plug from end of tool. Do this by pressing plug in and turning it 90 ° . This will release the plug from the tool body. 2. Remove the two springs within the cylinder at rear of tool body. 3. Use needle-nosed pliers to grasp nut at rear of firing pin assembly.
21 103500 T ool Assembly ATTACHING LINER TO TOOL BODY 1. Replace two ball bearings and springs into end of liner (see Figure 9, page 20). 2. Slide tool body onto liner. 3. Insert two screws into front of tool body just under liner. Tighten screws firmly.
22 103500 ATTACHING RUBBER PAD 1. Slip top of rubber pad over plug at rear of tool body (see Figure 5, page 19). 2. Press rubber pad into place. 3. Tighten screw on back of rubber pad with 5mm Allen wrench. ASSEMBLING BARREL ASSEMBLY 1. Insert guide into rear of base plate (see Figure 11).
23 103500 T roubleshooting Guide Piston hangs out of muzzle. Overdriven fastener. Piston jammed. Power load strip will not advance. Reduction or loss of power. Tool does not completely depress. Tool does not fire. Tool does not fire. Opening and closing of barrel or pushing down on tool, etc.
24 103500 Fasteners 482-80 Wood or Non-Metals To Concrete 482-79 Wood or Non-Metals To Steel 482-78 SP FASTENERS Fasten wood or nonmetals to concrete or steel.
25 103500 482-90 Application Chart IMPORTANT * Use power fastener with penetration control disc, part number 015549. • Recommended for use with Remington power load strips and power fasteners.
26 103500 Parts Central Contact authorized dealers of this product. If they can ’ t supply original replace- ment part(s), either contact your nearest Parts Central (see below) or call DESA International ’ s Parts Department at 1-800-972-7879 for referral information.
27 103500 Maintenance Log Date Maintenance Performed.
103500-01 REV. A 10/96 Limited W arranty Agreement DESA International warrants the Remington Powerdriver Model 493 against defects in materials and workmanship for a period of one (1) year from the date of purchase.
デバイスRemington 493の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Remington 493をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRemington 493の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Remington 493の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Remington 493で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Remington 493を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRemington 493の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Remington 493に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRemington 493デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
