RicohメーカーMP9060Aの使用説明書/サービス説明書
ページ先へ移動 of 40
Conventions Introduction Handling Procedures Features System environment Drive functions and settings Installing the Drive How to Use the Drive Specifications Contents Conventions Introduction Handlin.
Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " ● Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installa-tion or handling, or direct or indirect damages.
Conventions This manual uses the following symbols which indicate important information. Be sure to read the information. Ignoring this warning and incorrect handling may result in serious personal injury or damage to the product. Indicates restriction or caution that you should notice.
Introduction This manual contains important notes and product handling information. Be sure to read the manual before using the product. For easy reference in the future, please keep the manual at a handy location. Multimedia Printer series Thank you for purchasing the Multimedia Printer series drive MP9060A (hereafter referred to as the drive).
Handling Procedures Obey the following cautions when handling the drive or discs. Cautions During Installation ● Install the drive in accordance with the specifications. Be careful to avoid locations likely to cause vibration or shock. ● Avoid locations where there is high humidity, excessive dust, or poor ventilation.
when doing this. (See Fig. 1) ● After cleaning the disc with compressed air, place it on the disc tray and mount it. (See Fig. 2) ● We suggest using Perfect Duster II (80z.) as compressed air for cleaning. Other Cautions ● When moving the equipment, make sure that the disc has been removed from the drive.
fig1 Check 1. Recording surface 2. fig2 50 to 100mm 1. Back << Contents.
Features Completely sealed door construction provides high reliability. ● An improved anti-heat design means that no cooling fan is needed. ● Easy-to-use tray model. ● Enhanced-IDE (ATAPI) model ● Compliant with industry standard Orange Book Part II (CD-R) and Part III (CD-RW).
System environment Explains the system environment required for using the drive as a CD-R/CD-RW drive. PC IBM PC/AT compatible Operating System Windows 98/95 Windows NT Workstation Ver.4.0 (Service Pack 3) or later CPU 166MHz (or faster) Pentium Memory Windows 98/95 : 32MB or greater.
Specifications Drive | Disc Drive : MP9060A Type Internal type (bare drive) Interface Enhanced-IDE (ATAPI) Data buffer memory 2MB Data transfer speed 16.6MB/sec. (Max.) CD-R/CD-RW Write/Read speed (Ave.) 24X: 3.60 MB/sec. (Mode1, Mode2, Form1)[Read only] *1 20X: 3.
Weight Less than 1.5 Kg. Dimensions 148.4 X 198(included front panel) X 42.5mm Reliability Error Rate: 10 -12 bits or less MTBF: 100,000hours or greater MTTR: Within 30 minutes Environmental Conditions When operating When not operating Temperature 5°C to 40°C (No air cooling) -30°C to 65°C Humidity 55% to 90% R.
CD-R (74min./63min.) : Ricoh, Taiyo Yuden, Mitsubishi Chemical, Mitsui Chemicals, Ritek, CMC, Princo, TDK, Kodak, Memorex, Philips, and Maxell discs CD-R (80min.) *1 : Taiyo Yuden, TDK, Maxell, Philips CD-RW : Rioch, Mitsubishi Chemical, Memorex CD-RW (80min.
Drive functions and settings Front Panel | Rear panel Front Panel Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray.
Eject button This is the button used to eject or insert in the disc tray. 5. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage.
Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Caution Be careful to connect with the proper way. Connecting the wrong way may damage the system (and is not guaranteed).
Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. Follow the following procedures in such a case. Caution This feature is a last measure to be used only in an emergency.
Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position << Contents.
Disc ejection Press the eject button 1. Slowly take the disc out of the disc tray 2. Press the eject button or push the disc tray and the tray will be inserted back into the drive.
Caution After ejecting the disc, return the disc tray inside the unit quickly. When the disc tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure.
Load the disc 1. Press the eject button. 2. Place the disc on the disc tray. Be careful not to touch the recording surface of the disc. 3. Load the disc by pressing the eject button or by lightly pushing in the disc tray.
Next Load the disc | Disc ejection | Emergency Eject Using the Drive in a Vertical Position << Contents.
Using the Drive in a Vertical Position The drive can be installed in a vertical position. Locate the four tabs on the disc tray. Turn each of them inwards untill they click into place. 1. When loading a disc, insert it into the inner side of the tabs.
Installing the Drive Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure.
1. Jumper Set Up Before installation, set the jumper on the jumper connector on the rear panel. Master (MA) Drive set as Master (factory default) 1. Slave (SL) Drive set as Slave 2. Cable Select (CS) Drive mode set by CSEL on the host IDE interface Note The drive can be connected as the Master or Slave on an E-IDE (ATAPI) interface.
Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. ● Next 1. Jumper Set Up | 2. Removing the Computer Cover 3. Mounting the Drive | 4. Connecting the Power Connector 5.
2. Removing the Computer Cover Make sure all peripheral devices of the computer and the computer itself are turned off, and then remove the cover. Refer to the manual for the computer for details about removing the cover. Caution There may be sharp edges inside the computer take care to avoid injury.
3. Mounting the Drive Remove the 5 inch drive bay panel from the computer. Refer to the manual for the computer for details. 1. Insert the drive unit into the bay.
Secure the drive with the screws provided. If there is not enough space behind the drive, connect the E-IDE cables etc. before securing the drive. 3. Back Next.
1. Jumper Set Up | 2. Removing the Computer Cover 3. Mounting the Drive | 4. Connecting the Power Connector 5. PC Connections | 6. Sound Card Connection 7.
4. Connecting the Power Connector Connect the power cable from the computer's power supply to the socket on the drive unit, fitting the connector properly into the socket. If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type.
5. PC Connections The drive connects to the motherboard of the host computer using an IDE interface cable. Both Primary and Secondary connectors are usually provided on the motherboard, which may be connected as follows: Master 1. Slave 2. Motherboard 3.
.
To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel. Master drive (Booting hard disk) 1. Slave drive (MP9060A) 2.
Back Next 1. Jumper Set Up | 2. Removing the Computer Cover 3. Mounting the Drive | 4. Connecting the Power Connector 5. PC Connections | 6. Sound Card Connection 7.
6. Sound Card Connection If the computer has a sound card, the drive can be connected to the sound card with an audio cable. Make sure the connections are oriented so that L corresponds to L and R to R. Refer to the manual for the sound card for detailed infor-mation regarding connection.
1. Jumper Set Up | 2. Removing the Computer Cover 3. Mounting the Drive | 4. Connecting the Power Connector 5. PC Connections | 6. Sound Card Connection 7.
7. Replacing the Computer Cover When the installation of the drive unit is complete, replace the computer cover. Back Next 1. Jumper Set Up | 2. Removing the Computer Cover 3. Mounting the Drive | 4. Connecting the Power Connector 5. PC Connections | 6.
8. Device Drivers When using Windows 98/95 or Window NT Workstation Ver. 4.0, the installation of any special device drivers are not required. In order to ensure normal drive operation or if the drive.
How to Use the Drive Caution When using CD-ROM discs, DVD-ROM discs, CD-R discs or CD-RW discs, do not attach any stickers or labels to the discs. Using discs with labels attached not only causes read and write errors, but data on the disc may be lost due to dam-age to the disc itself.
* All references to the product in this doc ument are to specifications in effect when the product was released. Copyright RICOH Co.Ltd. All rights reserved.
デバイスRicoh MP9060Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ricoh MP9060Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRicoh MP9060Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ricoh MP9060Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ricoh MP9060Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ricoh MP9060Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRicoh MP9060Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ricoh MP9060Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRicoh MP9060Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。