RIDGIDメーカーR5013の使用説明書/サービス説明書
ページ先へ移動 of 18
1 Y our hammer drill ha s been engineered and manufactured to our high standard for dependability , ease of operation, and operator safety . When pr operly cared for , it will give you years of rugged, trouble-fr ee performance.
2 Introduction ...................................................................................................................................................................... 2 General Safety Rules ......................................
3 GENERAL SAFETY RULES WARNING: Read all instructions. F a i l u re t o f o l l o w a l l instructions listed below may r esult in electric shock, fire and/or serious injury . The term “power tool” in all of the warnings listed below r efers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
4 GENERAL SAFETY RULES W ear ear pr otectors with impact drills. Exposure to noise can cause hearing loss. Use auxiliary handles supplied with the tool.
5 SYMBOLS Some of the following symbols may be used on this product. Please study them and lear n their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer .
6 SYMBOLS SERVICE Servicing requir es extreme car e and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SER VICE CENTER for r epair . When servic- ing, use only identical replacement parts.
7 DOUBLE INSULA TION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cor d. All exposed metal parts ar e isolated from the internal metal motor components with protect- ing insulation.
8 Fig. 1 FEA TURES PRODUCT SPECIFICA TIONS Chuck Capacity ......................................................... 1/2 in. Input ........................................ 120 V , 60 Hz, AC only , 7.5 A Switch ..........................................
9 KNOW YOUR HAMMER DRILL See Figure 1. The safe use of this product requir es an understanding of the information on the tool and in this operator’ s manual as wel l as a know led ge of the pro jec t y ou ar e attem ptin g. Befo r e use of this product, familiarize yourself with all operating features and safety rules.
10 WARNING: Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict sever e injury . WARNING: Always wear safety goggles or safety glasses with sid e s hie lds wh en o per at ing pr oduct s.
11 OPERA TION RIGHT Fig. 4 WRONG Fig. 5 DRILL BIT TO TIGHTEN CHUCK JA WS TO INST ALL BITS See Figures 4 - 5 Unplug the drill. Insert the chuck key and twist counterclockwise. Ope n or clo se t he c hu ck j aw s to a poin t whe r e the o pe ni ng is slightly lar ger than the bit size you intend to use.
12 OPERA TION DEPTH STOP ROD Fig. 6 Fig. 7 DRILL BIT TO DECREASE DRILLING DEPTH AUXILIARY HANDLE ASSEMBL Y TO INCREASE DRILLING DEPTH DRILLING DEPTH AUXILIARY HANDLE ASSEMBL Y TO TIGHTEN TO LOOSEN 360° ROT A TION DEPRESS HERE TO ADJUST DEPTH STOP ROD USING THE AUXILIAR Y HANDLE ASSEMBL Y See Figures 6 - 7.
13 OPERA TION SELECTING HAMMER MODE OR DRILLING MODE See Figure 8. T o adjust for type of drilling, slide the selector on top of the motor housing to hammer mode or drilling mode. The ham- mer mode symbol is on the right and the drill bit symbol is on the left.
14 OPERA TION WARNING: Before connecting the drill to a power supply sour ce, always check to be sur e it is not in lock-on position (depress and release the switch trigger). Failure to ensure that it is not locked-on could result in accidental starting of the drill resulting in possible serious injury .
15 OPERA TION MET AL DRILLING� For maximum performance, use high speed steel bits for metal or steel drilling. Select normal drilling mode. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.� Maintain a speed and pressure which allows cutting without overheating the bit.
16 MAINTENANCE CHUCK REMOV AL See Figures 11 - 13. The chuck may be removed and r eplaced with a new one. Unplug the drill. Open chuck jaws using the provided chuck key . Insert a 5/16 inch or lar ger hex key into the chuck of the drill and tighten the chuck jaws securely .
17 W ARRANTY Pro of of pu rc ha se m u st b e p res en te d wh en req ue st in g warranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
18 OPERA TOR’S MANUAL 1/2 in. HAMMER DRILL DOUBLE INSULA TED R5013 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center .
デバイスRIDGID R5013の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RIDGID R5013をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRIDGID R5013の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RIDGID R5013の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RIDGID R5013で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RIDGID R5013を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRIDGID R5013の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RIDGID R5013に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRIDGID R5013デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。