RIDGIDメーカーR7111の使用説明書/サービス説明書
ページ先へ移動 of 16
1 Y our drill has been engineered and manufactur ed to our high standard for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance. WARNING: T o reduce the risk of injury , the user must read and understand the operator’ s manual before using this pr oduct.
2 Introduction ...................................................................................................................................................................... 2 General Safety Rules ......................................
3 GENERAL SAFETY RULES WARNING: Read all instructions. F a il u re t o f o l lo w al l instructions listed below may r esult in electric shock, fire and/or serious injury . The term “power tool” in all of the warnings listed below r efers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
4 GENERAL SAFETY RULES Use auxiliary handles supplied with the tool. Loss of control can cause personal injury . Hold power tools by ins ulate d grip ping surfac es whe n performing an operation where the cutting tool may contact hidden wiring or its own cord.
5 SYMBOLS Some of the foll owing symb ols may be used on this tool. Pleas e stu dy the m and learn the ir me aning. Pr oper inter pre tatio n of these symbols will allow you to operate the tool better and safer .
6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the pr oduct to your near est AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts.
7 DOUBLE INSULA TION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with pr otect- ing insulation.
8 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Chuck ....................................................................... 1/2 in. Switch ............................. VSR (V ariable Speed Reversible) No Load Speed ....................................0-850 r/min.
9 WARNING: If an y par ts ar e dam age d or mis sin g do not oper ate this tool until the parts are replaced. Failure to heed this warning could result in serious personal injury . WARNING: Do not attempt to modify this tool or cr eate accessories not recommended for use with this tool.
10 OPERA TION DIRECTION OF ROT A TION SELECTOR (FORWARD/REVERSE) See Figure 3. The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger .
11 OPERA TION USING THE AUXILIAR Y HANDLE ASSEMBL Y See Figure 6. Y our drill is equipped with an auxiliary handle assembly . For ease of operation, use the handle with either the left or right hand. The handle can be rotated 360°. T o adjust the auxiliary handle assembly: Loosen the handle assembly by tur ning the handle coun- terclockwise.
12 OPERA TION DRILLING See Figure 8. Depress and release the switch trigger to be sur e the drill is in the OFF position before connecting it to power supply . Check the dir ection of rotatio n selector for corr ect setti ng (forward or r everse).
13 MAINTENANCE WARNING: When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazar d or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
14 MAINTENANCE Look for these accessories where you pur chased this product: � High Speed Bits (For wood or metal) ...................................................................................................................... 1/2 in. � W ood Boring Bits .
15 W ARRANTY Pro of of p urch ase mu st b e p rese nte d wh en req ues tin g warranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
16 OPERA TOR’S MANUAL 1/2 in. DRILL DOUBLE INSULA TED R7111 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center .
デバイスRIDGID R7111の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RIDGID R7111をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRIDGID R7111の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RIDGID R7111の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RIDGID R7111で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RIDGID R7111を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRIDGID R7111の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RIDGID R7111に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRIDGID R7111デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。