RIDGIDメーカーR841151の使用説明書/サービス説明書
ページ先へ移動 of 22
R 22 22 20 This new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance.
2 T ABLE OF CONTENTS Introduc tion ................................................................................................................... ................................................. 2 General Saf ety Rules .
3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SA VE THESE INSTRUCTIONS WORK AREA K eep your w ork area clean and well lit .
4 SER VICE T ool service must be perf ormed only b y qualified repair personnel. Ser vice or maintenance perf or med by unqualified personnel ma y result in a risk of injur y . When servicing a tool, use onl y identical replace- ment parts. Follo w instructions in the Maintenance section of this manual.
5 WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion.
6 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
7 SPECIFICATIONS Chuck .......................................................................................................................... .................... 1/2 in. (13 mm) Keyless Motor ......................................................
8 30 min 30 min ? R 22 22 20 Fig. 1 BIT ST ORA GE DIRECTION OF RO T A TION SELECT OR (FORW ARD / REVERSE / LOCK OFF [CENTER LOCK POSITION] ) T ORQUE ADJUSTMENT RING FEA TURES KEYLESS CHUCK BA TTER Y PA C K DU AL PORT CHARGER DEPTH GA GE ROD 4-1/8 IN.
9 UNP A CKING INSTRUCTIONS When unpacking the tool: Carefully remov e the tool and accessor ies from the box. Make sure that all items listed in the pac king list are in- cluded. Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
10 ? 30 min 30 min Ev a lu a te E v a lu e r E v a lu a r Charging C a r g an d o E n ch a rg e Ful l Co m p le to C h a rge m a x . Power C orr ie nte Alim en ta tio n WARNING: Do not allow familiarity with the hammer drill to make you careless. Remember that a careless frac- tion of a second is sufficient to inflict severe injury.
11 30 min 30 min ? OPERA TION LED BA TTE R Y RED GREEN ACTION INDI CA T OR P A C K LED LED Power Without battery pack ON OFF Ready to charge battery pack Evaluate Hot battery pack Flashing OFF When ba.
12 Fig. 6 V ARIABLE SPEED SWITCH TRIGGER OPERA TION TO INSTALL BATTERY PACK Lock the switch trigger on the drill by placing the direction of rotation (forward-reverse) selector in center position. See Figure 4. Place batter y pac k in the drill.
13 This drill has an electr ic brake . When the trigger switch is released, the chuck stops turning. When the brake is functioning properly , spar ks will be visible through the v ent slots on the housing. This is normal and is the action of the bra ke .
14 22 18 16 20 R INSTALLING BITS See Figures 9 and 10. Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
15 22 18 16 20 R R 22 22 20 R 22 2 2 20 Fig. 13 T O DECREASE T ORQUE T O INCREASE T ORQUE ADJUSTING RING INSTALLING DEPTH GAGE ROD See Figures 11 and 12. A depth gage rod has been pack ed with your hammer drill to assist you in controlling the depth of drilled holes.
16 OPERA TION BIT STORAGE See Figure 14. When not in use, the bit provided with this drill can be placed in the storage area located on the rear of the drill.
17 TO ADJUST DRILLING OR HAMMER MODE See Figure 16. T o adjust hammer drill to dr illing or hammer operation, rotate mode selector in the direction of arrows as shown in Figure 16. For your con v enience a hammer symbol and drill bit sym- bol hav e been molded into the selector .
18 22 18 16 20 R 2 2 18 16 20 R 22 18 16 20 R Fig. 18 Fig. 19 Fig. 17 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replace- ment parts. Use of any other parts may create a hazard or cause product damage. Do not abuse pow er tools. Ab usive pr actices can damage tool as well as workpiece.
19 R E C Y C L E 1 . 8 0 0 . 8 2 2 . 8 8 3 7 RBRC Ni Cd ™ MAINTENANCE To obtain the longest possible battery life, we suggest the following: Store and charge your batteries in a cool area. Temperatures below 50°F or above 100°F will shorten battery life.
20 This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc. All warranty communications should be directed to One World Technologies, Inc.
21 NO TES.
OPERA T OR’S MANU AL 1/2 in. 18 V OL T HAMMER DRILL R841151 Customer Service Information: F or par ts or ser vice, contact y our nearest RIDGID author ized service center .
デバイスRIDGID R841151の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RIDGID R841151をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRIDGID R841151の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RIDGID R841151の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RIDGID R841151で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RIDGID R841151を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRIDGID R841151の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RIDGID R841151に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRIDGID R841151デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。