RIDGIDメーカーR86014の使用説明書/サービス説明書
ページ先へ移動 of 16
1 Y our drill has been en gineer ed and manufactur ed to our high standar ds for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance.
2 Introduction......................................................................................................................................................................2 General Safety Rules ..................................
3 GENERAL SAFETY RULES WARNING! RE AD AN D U NDE RS T A ND ALL IN ST RUC TI ON S. Failure to follow all instructions listed below , may r esult in elect ric sho ck, fir e and /or ser ious person al injury . SA VE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit.
4 GENERAL SAFETY RULES SPECIFIC SAFETY RULES H o l d t o o l b y i n s u l a t e d g r i p p i n g s u r f a c e s w h e n performing an operation where the cutting tool may con tact hidd en wiring . Con tact with a “live” wir e will also make exposed metal parts of the tool “live” and shock the operator .
5 SYMBOLS Some of the following symbols may be used on this product. Please study them and lear n their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer .
6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts.
7 FEA TURES PRODUCT SPECIFICA TIONS Chuck ...........................................................1/2 in. Keyless Motor .................................................................. 18 V olt DC Switch ..........................................
8 UNP ACKING This product has been shipped completely assembled. Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. Inspect the product carefully to make sure no breakage or damage occurred during shipping.
9 TO INST ALL BA TTER Y P ACK See Figure 2. Lock the switch trigger on the drill by placing the direc- tion of rotation (forward/reverse/center lock) selector in center position. Place battery pack in the drill. Align raised rib on battery pack with the groove inside the drill.
10 OPERA TION CAUTION: T o prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of r otation. T o stop the drill, release the switch trigger and allow the chuck to come to a complete stop. NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right.
11 OPERA TION Fig. 7 Fig. 8 Fig. 9 DRILL BIT OPEN (RELEASE) CHUCK JA WS GRIP (TIGHTEN) CHUCK BODY KEYLESS CHUCK RIGHT WRONG LED LIGHT See Figure 7. The LED light on the foot of the drill will come on when the switch trigger is depressed . This provi des additional lighting on the surface of the workpiece for operation in lower -light areas.
12 OPERA TION Fig. 10 DRILLING See Figure 10. Check the direction of r otation selector for the correct setting (forward or r everse). Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.
13 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replacement parts. Use of any other parts may create a hazar d or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
14 MAINTENANCE CHUCK REMOV AL See Figures 11 - 13. The chuck may be removed and r eplaced by a new one. Lock the swit ch trig ger by placing the dir ect ion of rota tion selector in center position. Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely .
15 W ARRANTY Proof of purchase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
16 OPERA TOR’S MANUAL 1/2 in. 18 VOL T LITHIUM-ION AutoShift ™ DRILL R86014 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all r elevant information when you call or visit.
デバイスRIDGID R86014の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
RIDGID R86014をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRIDGID R86014の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。RIDGID R86014の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。RIDGID R86014で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
RIDGID R86014を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRIDGID R86014の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、RIDGID R86014に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRIDGID R86014デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。