RokuメーカーBrightSignの使用説明書/サービス説明書
ページ先へ移動 of 11
1 BrightSign User Guide October 6, 2006 Palo Alto, California USA www.rokulabs.com.
2 Table of Contents INTRODUCTION ................................................................................................................... .......... 3 E XAMPLES ...............................................................................
Introduction The Roku BrightSign HD600 is a complete stan dalone Digital Sign or Kiosk Controller that can play content from st andard Flash memory cards or over an Ethernet network. BrightSign can be used in looping or inte ractive modes while displaying video and images on almost any standard or high defi nition display.
4 Example BrightSign Setup s Probably the simplest way to use BrightSign is to put a video or set of still images on a CompactFlash card, and use a VGA cable to co nnect the BrightSign to a flat panel monitor.
5 Playing Media with BrightSign Media can autoplay from a CompactFlash car d, be played via a sc ript on a CompactFlash card, or can be tested using the serial shell commands. Auto Playing a Video File Upon Power-up To autoplay a video file on powe r-up or reset, do the following: 1.
6 6. After a few moments, the slide show should play and auto loop. Auto Executing a Script Upon Power-Up 1. Create the script using a text edito r (see th e script section of this manual for more information) 2. Save it to the root directory of your CompactFlash card with the nam e “autorun.
7 Device Sof tware and Upgrading The BrightSign HD600 is pre-programmed with two primary software images: a “Safe Mode” and a “Run Mode”. The Safe Mode software image is write protected, and not changed once programmed by the factory. Its main purpose is to validate that the run mode rom image is not corrupt, and boot the unit.
8 3. Configure the terminal for: 9600 baud, 8 da ta bits, no parity, 1 stop bit, NO flow control, “TTY mode”. 4. Insert a CF card into BrightSign with so me test files on it (24 bit BMP graphics, 48KHZ mp3 files, VOB video, etc) 5. Optionally connect speakers or VGA monitor to the BrightSign 6.
9 • Speakers/Amplifiers with stereo line-lev el inputs • Audio playback devices with SPD IF optical digital audio input • PC via Serial Port • IR Remote Control using the “NEC” prot ocol.
10 Roku Objects Take a look at the section of this manual titled “Auto Playing a Video Upon PowerUp”. It shows a simple five line script to aut oplay a video, looping.
11 270 msg = wait (500, tmr) 280 sw.SetOutputState(butn+17,0) 290 msg=p.GetMessage(): if type(msg)<>"rotINT32" then 290 300 goto 220 Learning More and Support The following resources can help you get the most from your BrightSign: 1. Visit www.
デバイスRoku BrightSignの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Roku BrightSignをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRoku BrightSignの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Roku BrightSignの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Roku BrightSignで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Roku BrightSignを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRoku BrightSignの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Roku BrightSignに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRoku BrightSignデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。