AudiovoxメーカーLCM5043NPの使用説明書/サービス説明書
ページ先へ移動 of 20
LCM5043NP & LCM5643NP Remote Controlled Color Display Monitor with Headphone Jack Installation and Owner's Manual EL E C T R O N I C S C O R P .
1 EXPLANA TION OF GRAPHIC SYMBOLS W ARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: 1. This product is designed to operate with a 12 volt, negative ground bat- tery system. 2. Disconnect the ground wire from the battery terminal before connecting the electrical system.
2 SYSTEM OVERVIEW The LCM5043NP is comprised of a 5" Thin Film Transistor (TFT) Liq- uid Crystal Display ( LCD) Monitor . The LCM5643NP is comprised of a 5.
MA TERIALS LIST 1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.) 2. Remote Control Unit (136B2156) with Lithium Battery , 3V ,CR 2025 (1pc.) 3. Interconnect Box (136B2183) (1pc.) 4. Monitor Cable, 8' (1 12B3152) (1pc.) 5. Headrest Mounting Tray (LCM5043NP=102C3740) or (LCM5643NP=102C3742) (1pc.
VEHICLE PREP ARA TION 1 ) Decide on the system configuration and the options that will be in- stalled (i.e. what components, VCP , DVD, TV T uner , Video Game, Monitor , FM Modulator , etc.). 2 ) Read the manuals and get familiar with the electrical requirements and connections.
5 10 ) After verifying the proper operation of the system, proceed to mount each component. 1 1 ) The mounting method, and the location will vary from vehicle to vehicle, so this manual will only focu.
6 3 ) Adjust viewing angle of monitor by tightening the fastener at the side. 4 ) When the system components are mounted, test the system to verify that it is functioning correctly . Make sure that no wiring was pinched, or connected improperly during the final installation.
7 1 ) Remove the headrest from the vehicle for easiest installation. 2 ) Lay headrest on a flat surface. 3 ) Center trim collar on headrest as shown. NOTE: Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down. 4) Using a Permanent Marker , mark headrest material along the interior of the Trim Ring.
9 ) Using your fingers, tear the foam out of the headrest leaving a re- cess where the shell will be in- serted. NOTE: At this point you will need to install the harness up through the area into the recess. It may be helpful to follow one of the posts and tie wrap it to the post for restraint.
1 1 ) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor . Make sure the connector locks into place. Insert the Monitor into the Mounting Tray and secure the cable using tie wraps or screws 1 2) Turn the Monitor around and in- sert it into the Mounting Tray housing.
ELECTRICAL CONNECTION (Wiring Diagram) 10 Video Source Input (1&2) Not Used A V Output.
The following procedure is to remove the Monitor from the Mounting T ray using the supplied Removal T ool. NOTE: Use care when per- forming this procedure not to scratch any exposed surfaces with the edges of the Removal T ool. Masking tape applied to the two tips or legs of the Removal T ool will help prevent scratching.
CONTROLS AND INDICA TORS Headphone OPERA TION 1. Press power On/Off button to the On position. The LED power indicator will light red. 2. Press the Picture Select button to adjust the picture display characteristics. The adjustments will be shown on the On Screen Display in the following sequence: Contrast, Brightness, Color , and TINT .
MAINTENANCE T o avoid electrical shock, do not open the enclosure. High voltage is present. No user serviceable parts inside the enclosure. Do not use any chemical solvent, cleaning agent or corrosive de- tergent to clean away dirt on the surface of the screen.
REMOTE CONTROLLER NOTE : The Remote Controller supplied with this system is a stan- dard remote control, which is used to operate other systems. The Remote Controller is not a universal remote and will only perform the functions described herein. Only the Keys highlighted on the Remote Controller image bellow are used to operate this system.
15 MENU FUNCTION KEY : The MENU Key is used to navigate between the Color , Brightness and Tint adjustment modes. When the MENU Key is pressed an On Screen Display(OSD) will appear as shown bellow . OSD Press release and tap the MENU Key until the desired adjustment mode is selected.
16 NOTE: For the LCM5643NP - Select either * NTSC or P AL, press the p or q Keys ( CH/DISK/SET ). VOLUME CONTROL KEY : T o switch between Video Input Sources (A V1 and A V2) press and release the MODE Key . VIDEO SOURCE MODE KEY : T o increase or decrease the V olume, press and hold the VOL p or q Key until the desired volume is reached.
17 Replacement of Remote Controller Battery: 1. Use a small coin to pry open battery holder from compartment. 2. Remove old battery and put in a new one with positive sign “ + “ facing upward. 3. Push compartment into position. Precaution: 1. Dispose off used battery properly .
18 LCM5043NP: LCD Panel Size (Diagonal) ................................... 5 " LCD Panel Format ................................................. 960 x 234 dots LCD Panel Resolution ........................................... 224,640 pixels LCD Backlight Life .
© 2002 Audiovox Electronics Corp., Hauppauge, NY 128-6323 AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part there.
デバイスAudiovox LCM5043NPの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audiovox LCM5043NPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox LCM5043NPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox LCM5043NPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox LCM5043NPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox LCM5043NPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox LCM5043NPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox LCM5043NPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox LCM5043NPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。