AudiovoxメーカーMA200Cの使用説明書/サービス説明書
ページ先へ移動 of 12
1 REMOTE CONTROL MOT ORCYCLE ALARM SYSTEM INST ALLA TION GUIDE AND OWNERS MANUAL MODEL MA200C.
2 MOUNTING THE SIREN/CONTROL MODULE 1. Choose a location that is away from hot and mov- ing parts considering the Red wire length must be connected to the to the positive terminal of the bat- tery . Prevent access to the siren as much as pos- sible, by mounting in a hidden location.
3 BLACK (LONG): Using the attached wire lug, connect the Black (long) wire of the siren to the negative terminal of the battery or a good ground source. BLACK (SHORT): Stretch the short Black antenna wire as long as pos- sible, avoiding metal contact if possible.
4 CONNECTING THE RELAY (HORN FEATURE) IMPORTANT! The relay has been shipped with the BLACK wire loaded into terminal 87a of the Relay Socket. The wire must be removed from this location and placed into the outer terminal of the Relay Harness 87. 1 . Connect the ORANGE wire from the relay harness to the BROWN/BLACK wire from the main harness.
5 CONNECTING THE RELAY (STARTER/IGNITION) IMPORTANT ! When using the relay to disable the starter, leave the BLACK wire in ter- minal 87a of the relay connector in the location shown in the Figure 5. 1. Connect the ORANGE wire from the relay harness to the ORANGE wire from the siren harness.
6 CONNECTING THE RELAY (HEAD LAMP FLASH FEATURE) IMPORTANT! When using the relay to flash the vehicle’s parking lights, unload the BLACK wire from terminal 87A of the relay harness and load it into terminal 87. Refer to Figure 6. 1 . Connect the ORANGE wire from the relay harness to the WHITE wire from the main harness.
7 2 . Turn the ignition "ON" then "OFF" 5 times. The system will sound a long chirp to confirm entry into the program mode. 3 . Press the "LEFT" button of each transmitter to be programed (up to Two Transmitters). The siren will chirp to confirm each transmitter is now programmed.
8 NOTE: If the alarm issues three warnings within 15 seconds, the siren will sound a regular alarm tone which lasts for 30 seconds. After 30 seconds, the siren will automatically stop and the alarm will arm itself. OPERATING THE SYSTEM Operation of the system is described in this section.
9 To activate the panic feature: 1 . Press and hold button 1 on the keychain transmitter for 3 seconds. 2 . The alarm will sound, and continue to sound for 30 seconds. 3 . To silence the alarm before the 30-second shut- down, press and hold button #2 on the keychain transmitter.
10 Replacing the Transmitter Battery The keychain transmitters have a small, red LED visible through the top cover. This LED can be used to indicate battery condition. You will also notice a decrease in effective transmitter range as the battery deteriorates.
11 TROUBLESHOOTING: Symptom: The Transmitters will not program to the control module. Check: 1. Verify that the 1 Amp fuse in the red wire from the siren control module is in good condition. Replace it if it is blown. 2. Verify that the connections of the red and black wires have been made according to the wiring section of this manual.
12 © 2002 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-6276 999 .audiovo x.com For C ust omer Ser vi ce Vi si t Ou r W ebsi te At Product I n f orm ati on, Photos, F A Q’ s O wner’ s Manu.
デバイスAudiovox MA200Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audiovox MA200Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudiovox MA200Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audiovox MA200Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audiovox MA200Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audiovox MA200Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudiovox MA200Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audiovox MA200Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudiovox MA200Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。