RyobiメーカーDrill Pressの使用説明書/サービス説明書
ページ先へ移動 of 25
Oper a tor´s manual 371K 375K Please read these instructions car efully and make sur e you understand them bef ore using the machine. English.
2 – English WARNING! The power cutter can be dangerous! Careless and incorrect use can result in serious or fatal injury to the operator or others. SYMBOL EXPLANA TION Symbols on the power cutter: Please read the instructions carefully and make sure you understand them before using the power cutter.
English – 3 CONTENTS List of Contents Symbol explanation ..................................................... 2 Safety instructions P ersonal protective equipment ....................................... 4 The power cutter’ s saf ety equipment ...
4 – English ! SAFETY INSTR UCTIONS ! ! THE PO WER CUTTER’S SAFETY EQUIPMENT This section describes the power cutter ’ s safety equipment, its function and how checks and maintenance are carried out to ensure that it operates correctly. (See the chapter “What is what“ to locate where this equipment is positioned on your power cutter.
English – 5 The muffler is designed to give the lowest possible noise level and to direct the engine‘s exhaust fumes away from the user. The engine‘s exhaust fumes are hot and can contain sparks, which can lead to the outbreak of fire.
6 – English 3 Muffler Never use a machine that has a defective muffler. Check regularly that the muffler is secured to the engine body. SAFETY INSTR UCTIONS GENERAL SAFETY INSTRUCTIONS IMPORTANT INFORMATION! Do not use the power cutter until you have read the entire contents of this Operator ’ s Manual.
English – 7 SAFETY INSTR UCTIONS ! Fuel safety (Filling/Fuel mixture/Storage) WARNING! Exercise great care when handling fuel. Bear in mind the risk of fire, explosions and inhaling fumes. • Never fill the machine while the engine is running. • Provide good ventilation when filling or mixing fuel (petrol and 2-stroke oil).
8 – English SAFETY INSTR UCTIONS ! WARNING! Over exposure to vibrations can result in blood-vessel or nerve injury to persons suffering with blood circulation problems. Seek medical attention if you experience physical symptoms that can be related to over exposure to vibrations.
English – 9 SAFETY INSTR UCTIONS Pull in Pull in occurs when the lower part of the blade is suddenly stopped or when the cut closes. (To avoid this see the section ” How to avoid kickback ” and ” Pinching/rotation ” below). Pinching/rotation Pinching occurs when the cut closes.
10 – English SAFETY INSTR UCTIONS CUTTING BLADES General Cutting blades are available in two basic designs; abrasive discs and diamond blades. Only abrasive discs and diamond blades may be used and only within their respective application areas. Abrasive discs The cutting material on abrasive discs consists of grit bonded using an organic binder.
English – 11 SAFETY INSTR UCTIONS Diamond blades Diamond blades consist of a steel body with segments that contain industrial diamonds ! WARNING! Cool diamond blades continuously with water to prevent overheating that can cause the blade to break and pieces being thrown off resulting in injury and damage.
12 – English WHA T IS WHA T? What is what on a po wer cutter? 17 13 11 8 10 9 12 21 2 15 18 4 7 3 16 20 1 19 14 5 6 22 23 1. Cylinder cover 2. Muffler 3. Fuel tank 4. Rear handle 5. Choke / Throttle trigger lockout 6. Throttle catch 7. Stop switch 8.
English – 13 Fitting the cutting blade Husqvarna cutting blades are manufactured and approved for freehand cutting. The paper labels on each side of the blade are there to distribute the pressure from the flange washer and prevent the blade from slipping.
14 – English FUEL HANDLING ! Fuelling WARNING!The following precautions reduce the risk of fire: • Do not smoke or place any sources of heat in the vicinity of the fuel. • Never refuel when the engine is running. • Open the fuel cap slowly when fuelling so that any over pressure is released slowly.
English – 15 Start and stop WARNING! Before starting observe the following: • Do not start the power cut without the cutting arm or cutting head fitted. Otherwise the clutch can come loose and cause personal injury. • Always move the power cutter from the filling area before starting.
16 – English Adjusting the drive belt • The drive belt is fully enclosed and well protected from dust, dirt and mechanical effects during the cutting process. • To tension the drive belt, slightly loosen the bolts (A), which secure the cutting head and belt guard.
English – 17 MAINTENANCE Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in.
18 – English MAINTENANCE Fuel filter • The fuel filter sits inside the fuel tank. • The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by blockage of the fuel filter. • The filter cannot be cleaned but must be replaced with a new filter when it blocked.
English – 19 ! Tensioning the recoil spring • Lift up the starter cord from the cut out on the pulley and turn the pulley approx. 2 turns clockwise. NOTE! Ensure the starter pulley can be turned at least a further 1/2 turn when the starter cord is fully extended.
20 – English MAINTENANCE Spark plug The condition of the spark plug is affected by: • An incorrect carburettor setting. • An incorrect fuel mixture (too much oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties.
English – 21 MAINTENANCE 5 4 17 18 11 19 3 8 10 15 1 13 16 7 Below follows some general maintenance instructions. If you need further information please contact your service workshop. 9 14 2 3 6 12 8 15 W eekly maintenance 8. Clean the main filter. 9.
22 – English TECHNICAL DA T A Engine Cylinder volume, cu.in/cm 3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Max. speed, unloaded, rpm Power, kW Ignition system Manufacturer Type of ignit.
English – 23 EU declaration of conformity (Only applies to Europe) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel. +46-36-146500, declare under sole responsibility that the power cutters Husqvarna.
´®z+H2^¶6`¨ 2003W14 114 01 86-26.
We hope you find the links below useful. For further ga rdening information visit www.GardenResources.c o.uk Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mower.
デバイスRyobi Drill Pressの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ryobi Drill Pressをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi Drill Pressの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi Drill Pressの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi Drill Pressで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi Drill Pressを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi Drill Pressの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi Drill Pressに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi Drill Pressデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
