Ryobi OutdoorメーカーPBC3046Bの使用説明書/サービス説明書
ページ先へ移動 of 22
Y our new trimmer has been engineered and manuf actured to Ryobi’ s high standard for dependability , ease of operation and operato r saf ety . Properly cared for , it will giv e you years of rugged, troub le-free performance. Thank you f or b uying a Ryobi trimmer .
2 ■ ■ ■ ■ ■ Safety ......................................................................................................................... ............................................ 2 - 3 ■ ■ ■ ■ ■ Symbols .....................
3 ■ ■ ■ ■ ■ Inspect the unit before each use for loose fasteners, fuel leaks etc. Replace any damaged parts before use. ■ ■ ■ ■ ■ The string head or blade will rotate during carburettor adjustments.
4 SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely. SYMBOL NAME EXPLANATION Safety Alert Symbol Indicates danger, warning or caution.
5 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
6 Fig. 1 THROTTLE TRIGGER STARTER GRIP ENGINE HOUSING THROTTLE INTERLOCK IGNITION SWITCH TRI-ARC BLADE BLADE GUARD SHAFT STRAP HANGER SHOULDER STRAP LEFT HANDLE GEAR HEAD FEA TURES TRIGGER HANDLE UNP A CKING INSTRUCTIONS ■ ■ ■ ■ ■ Carefully remove the product from the carton.
7 HANDLE See Figure 2. 1. Place the handlebar in the bottom clamp located on the shaft housing. NOTE: The throttle trigger must be mounted to the operator’s right side. 2. Insert the square tab of top clamp into the mounting hole of the bottom clamp.
8 GRASS DEFLECTOR AND BLADE GUARD USE NO TE: When conv er ting from br ushcutter to trimmer , or trimmer to br ushcutter , make sure the correct guard/ deflector is being used. See Figure 5. SILENCER GUARD ASSEMBLY See Figure 4. 1. Remove silencer guard and two screws from the owner’s kit.
9 ASSEMBL Y BLADE GUARD See Figure 6. 1. Attach the blade guard to the mounting bracket; install the four screws (10-24 x 3/4 in) from the top of the mounting bracket through the blade guard and into the threaded mounting plates. 2. Using the torque wrench supplied, tighten all four screws securely.
10 ASSEMBL Y BLADE CUPPED WASHER BLADE NUT HOLDING PIN Fig. 8 SPANNER (13 mm) UPPER FLANGE WASHER INSTALLING THE BLADE See Figure 8. 1. Place the upper flange washer over the gear shaft with the hollow side toward the blade guard. 2. Centre the blade on the upper flange, making sure the blade sits flat.
11 FUEL AND REFUELLING HANDLING THE FUEL SAFELY ■ ■ ■ ■ ■ Always handle fuel with care. It is highly flammable. ■ ■ ■ ■ ■ Always refuel outdoors where there are no sparks and flames. Do not inhale fuel vapour. ■ ■ ■ ■ ■ Do not let petrol or oil come in contact with your skin.
12 OPERA TION ADVANCING THE STRING ADVANCING STRING USING THE EZ LINE™ TAP ADVANCE SYSTEM String advance is controlled by tapping string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string.
13 OPERA TION W ARNING: Extreme care must be taken when using blades to insure safe operation. Read the safety information for safe operation using the blade, refer to “Specific Safety Rules for Brushcutter and Blade Use” earlier in this manual. ■ Always hold brushcutter with both hands when operating.
14 PRIMER BULB LEVER Fig. 15 W ARNING: Never start or run the engine inside a closed or poorly ventilated area; breathing exhaust fumes can kill. IGNITION SWITCH I = ON TO RUN O = OFF TO STOP Fig. 14 THROTTLE TRIGGER INTERLOCK TO START A COLD ENGINE: 1.
15 ■ You may make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorised servicing dealer. ■ Consequences of improper maintenance may include excess carbon deposits resulting in loss of performance and discharge of black oily residue dripping from the silencer.
16 STRING REPLACEMENT See Figures 18, 19, 20 and 21. 1. Stop the engine, disconnect the sparking plug wire. Hold the string head and unscrew the spool retainer. Turn clockwise. 2. Remove the spool from the string head. NOTE: Keep the spring attached to the spool.
17 MAINTENANCE Fig. 23 Fig. 24 LATCH PULL COVER TO OPEN TABS ON AIR FILTER COVER SLOTS ON AIR FILTER BASE FILTER CLEANING THE EXHAUST PORT AND SILENCER Depending on the type of fuel used, the type and amount of oil used and/or your oper ating conditions, the exhaust port and silencer may become blocked with carbon deposits.
18 The fuel cap contains a non-serviceable filter and a check valve. A clogged fuel filter will cause poor engine perfor- mance. If performance improves when the fuel cap is loosened, the check valve may be faulty or the filter clogged. Replace fuel cap if required.
19 PROBLEM POSSIBLE CAUSE SOLUTION IF THESE SOLUTIONS DO NO T SOL VE THE PROBLEM, CONT A CT Y OUR A UTHORISED SER VICE DEALER. TR OUBLESHOO TING 1. Check spark. Remove sparking plug. Reattach the sparking plug cap and lay sparking plug on metal cylinder .
20 TR OUBLESHOO TING 1. Lubricate with silicone spray. 2. Install more string. Refer to “String Replacement” earlier in this manual. 3. Pull strings while alternately pressing down on and releasing spool retainer. 4. Remove string from spool and rewind.
21 SOUND POWER/PRESSURE AND HANDLE VIBRATION CHART FOR STRING TRIMMERS / BRUSHCUTTERS Information on Noise Emission per European Machine Safety Directive 98/37/EC. The individual equipment listed was operated in a manner consistent with normal working conditions.
983000-323 6-03 OPERA T OR’S MANU AL T rimmer / Brushcutter PBC3046B R Y70107A Ry obi T echnologies GmbH Itterpark 7 D-40724 Hilden Germany T el.: +49 (0)2103 / 29 58 0 F ax : +49 (0)2103 / 29 58 29 info@ryobi-rtg.
デバイスRyobi Outdoor PBC3046Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ryobi Outdoor PBC3046Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi Outdoor PBC3046Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi Outdoor PBC3046Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi Outdoor PBC3046Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi Outdoor PBC3046Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi Outdoor PBC3046Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi Outdoor PBC3046Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi Outdoor PBC3046Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
