Auto PageメーカーRF-502の使用説明書/サービス説明書
ページ先へ移動 of 18
RF - 502 OPERATION INSTRUCTIONS.
Congratulations on your purchase of the RF - 502 vehicle security system. AutoPage, Inc. is one of the companies with the longest history and experience in vehicle security in the United States and a wh olly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
RF - 502 1 RF - 502 OPERATION I NSTRUCTIONS A. REMOTE CONTROL TRANSMITTER OPERATION The new remote control transmitter (XT - 54) included with the RF - 502 offers the code rolling feature which will prevent illegal use of a code - grabber with an attempt to record the code of your transmitter.
RF - 502 2 particular operation. The sequence must be repeated each time if it is desired to cancel the arm/disarm chirp sound. 3. PANIC FUNCTION The RF - 502 remote control may be used as a remote panic switch to trigger the siren in cases of emergency.
RF - 502 3 To replace the battery, carefully remove the case screw located at the end of the remote where the key ring attaches to the case. Use a small blade Phillips screwdriver.
RF - 502 4 D. VALET/OVERRIDE SWITCH NOTE : Both VALET and OVERRIDE functions are performed from the same switch. 1. OVERRIDE FUNCTION The OVERRIDE FUNCTION may be used if the RF - 502 remote is lost or inoperative. To operate the OVERRIDE FUNCTION, enter the vehicle (siren will sound); switch the vehicle ignition to ON.
RF - 502 5 E. PASSIVE/MANUAL ARMING OPERATION (Optional at installation) Passive/Manual operations can be selectable if an optional toggle switch is installed. Consult your installing dealer. 1. PASSIVE ARMING If you choose the PASSIVE (aut omatic) mode, the system must be operated as below.
RF - 502 6 Approach the vehicle and press the ON/OFF remote transmitter button. The siren will chirp 2 times and the lights will flash to indicate the RF - 502 is disarmed.
RF - 502 7 1. Open any door or other protected opening. The siren will sound instantly, and the lights will flash. 2. If the pre - warning feature is activated, the RF - 502’s SIS - 5 impact sensor will respond to a light shock with a chirp sound, and trigger the alarm when a heavier shock is detected.
RF - 502 8 4. Turn the igniti on switch "ON/OFF", "ON/OFF". The siren will chirp one (1) time. You are now in the programming mode. 5. Press the ON/OFF button on one of the remote transmitters until the alarm siren responds with a confirming chirp.
RF - 502 9 Enter the programming mode on vehicle #1 and push the ON/OFF button on the tran smitter for Vehicle #1. The alarm siren will respond with a confirming chirp. Within five (5) seconds , push the AUX button on the transmitter for Vehicle #2. The alarm siren will respond with a confirming chirp.
RF - 502 10 AUTOPAGE ALARM ACCESSORIES AP - 4000DX Paging System Vehicle secu rity paging was originated by AutoPage over 18 years ago. The AP4000DX is our latest version providing a full four watts of output power to signal a handsome belt - clip paging receiver indicating your RF - 502 has been triggered, even if you cannot hear the siren.
RF - 502 11 sensors, the SIS - 10 has a LED and potentiometer for easy sensitivity adjustment. MSEN - KIT The MSEN - KIT includes two pre - wired Micro Resonance Sensors and a special triggering amplifier.
12 LIMITED LIFETIME WARRANTY PROVISIONS (U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
RF - 502 13 7 AutoPage shall not be liable, under the foregoi ng WARRANTIES or otherwise, for: Any personal injury of any kind to the purchaser, its employees or agents or anyone else whomsoever resul.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service.
13 DATE SERVICE COMPLETED.
1815 W. 205th St. #101 Torrance, CA 90501 310 - 618 - 2002.
デバイスAuto Page RF-502の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Auto Page RF-502をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAuto Page RF-502の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Auto Page RF-502の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Auto Page RF-502で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Auto Page RF-502を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAuto Page RF-502の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Auto Page RF-502に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAuto Page RF-502デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
