SceptreメーカーX20WG-Nagaの使用説明書/サービス説明書
ページ先へ移動 of 24
X20 W G - Naga User ’ s Manual.
i FCC Compliance Statement This device complies with part 15 of t he FCC Rules. Operation is subject to the following two conditions: 1. This device may not caus e harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
ii To comply with the limits for an F CC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expre ssly approved by the party responsible for compliance could void the user ’s authority to operate the equipment.
iii T ABLE OF C ONTENTS TABLE OF CO NTENTS .......................................................................................... III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Ad.
1 Rev.3 The LCD Monitor Your New LCD Monitor Your LCD Monitor has been desi gned to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x350 VGA to 1680x1050 WSXGA+.
2 Rev.3 Note: Using a computer for an extended period of time with a poor workstation set-up and incorrect working habits can c ause health problems. The science of ergonomics studies the relationship between health and a suitable working environment.
3 Rev.3 Identifying Components A. The LCD Monitor — Front View Figure 1-1: The LCD Monitor Front View 1. Sceptre logo Indicator This foursquare LED indicator blue lit when the power is on and red lit when the LCD monito r is in power-saving mode. 2.
4 Rev.3 B. "Hot Keys" for Quick Adjustment of Monitor Settings Figure 1-2: "Hot Keys" 1. Brightness adjustment " Hot Key ": Press this Z button to allow you to adjust the brightness of the LCD Monitor directly < > 50 2.
5 Rev.3 Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0 ° to 10 ° . 10 Figure 1-3: Tilting the Monitor 0 to 10.
6 Rev.3 Connecting AC Power and PC Video Ca ble Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. Figure 1-4: PC cone nction Power Management System This LCD Monitor complies with the VESA DPMS power management proposal.
7 Rev.3 How to install the detacheable stand: Please see the below drawing..
8 Rev.3 The Display Controls The LCD Monitor’s Control Panel Figure 2-1: The Control Pa nel 1. Hot key button Y & Z These buttons let you to adjustment volume and brightness of the LCD Monitor directly 2.
9 Rev.3 Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the OSD Menu button causes the screen below to appear. 2. Use the - & + key to select the desired group, then press Menu key to the sub-menu 3. Repeat step 2 to select the changed item, then press - & + to change the value.
10 Rev.3 Auto Adjust Option The Auto Adjust option lets the monitor determine and select the settings that are most appropriate for your system requirements.
11 Rev.3 Color -- Color Temperature Adjustment Auto Color -- To adjust automatically the white balance display. 9300 -- Sets the color temperature to 9300K 6500 -- Sets the color temperature to 6500K .
12 Rev.3 OSD – OSD Adjustment H. Position -- Moves the OSD menu horizontally V. Position -- Moves the OSD menu vertically OSD Time -- Sets the OSD time ( 0 to 60 second ) Exit -- Return to the previ.
13 Rev.3 Miscellaneous Input selection -- To switch between analog and DVI port for PC signal input Sharpness -- The sharpness value can be set at 1. 2.
14 Rev.3 Note: 1) No signal detected When the monitor is ON and there is no video signal received, the following message will be displayed No signal detected! 2) Signal out of range When the frequency.
15 Rev.3 Appendix A TFT LCD Monitor Specifications Item Specification LCD Panel 20.1" WSXGA+ Control Functions Power Software Power switch with LED indicator (ON/OFF) Main Menu Submenu Auto adjust Luminance Brightness/Contrast/ /Exit Geometry H.Position/V.
16 Rev.3 Video Interface VGA Compatible Analog RGB DVI compatible signal Scanning Frequency H/V, Hz 31K-80K 60-75 P o w e r Management M e e t s VESA DPMS Power Consumption (ON/OFF, W) 45W/1W Max. Dimensions WxHxD 18.72 x 16.14 x 6.89 in. (475.4 x 410 x 175mm) Net Weight (approx.
17 Rev.3 Appendix B Supported PC Timing Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 DOS 720x400 28.32 70.08 31.47 2 DOS 640x480 25.18 59.94 31.47 3 Macintosh 640x480 30.24 67.00 35.00 4 VESA 640x480 31.
18 Rev.3 Supported Video mode Item Standards Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 720x480i 29.97 15.73 2 720x480P 59.
19 Rev.3 Appendix C Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear disp lay when a new display mode or new VGA card is selected.
20 Rev.3 PC’s VGA card may be out of the LCD’s synchronous range. Change to one of the alternate m odes listed in Appendix B, or replace the VGA card and repeat steps 1 and 2. 4. If the power LED is not lit, check that the AC power connector is securely connected, and verify that the AC adapter LED is lit.
デバイスSceptre Sceptre X20WG-Nagaの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sceptre Sceptre X20WG-Nagaをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSceptre Sceptre X20WG-Nagaの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sceptre Sceptre X20WG-Nagaの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sceptre Sceptre X20WG-Nagaで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sceptre Sceptre X20WG-Nagaを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSceptre Sceptre X20WG-Nagaの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sceptre Sceptre X20WG-Nagaに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSceptre Sceptre X20WG-Nagaデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
