Sceptre TechnologiesメーカーX7g-NagaVの使用説明書/サービス説明書
ページ先へ移動 of 22
X7G-NagaV User ’ s Manual.
i FCC Compliance Statement This device complies with part 15 of t he FCC Rules. Operation is subject to the following two conditions: 1. This device may not caus e harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
ii The Federal Communications Commission warns that changes or modifications of the unit not expre ssly approved by the party responsible for compliance could void the user ’s authority to operate the equipment.
iii T ABLE OF C ONTENTS TABLE OF CO NTENTS .......................................................................................... III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Ad.
1 Rev.1 The LCD Monitor Your New LCD Monitor Your LCD Monitor has been desi gned to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA.
2 Rev.1 After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-T o-PC Analog signal cable 15pin • User ’s manual If you find that any item to be missing or appear to be damaged, contact your dealer immediately.
3 Rev.1 Identifying Components A. The LCD Monitor — Front View Figure 1-1: The LCD Monitor Front View 1. Pow er-On Indicator This Circular LED indicator green lit when the power is on and orange lit when the LCD monitor is in power-saving mode. 2. Monitor Stand 3.
4 Rev.1 B. "Hot Keys" for Quick Adjustment of Monitor Settings Figure 1-2: "Hot Keys" 1. Brightness Adjustment "hot key": Press this + button to allow you to adjust the brightness of the LCD Monitor directly Brightness 50 2.
5 Rev.1 Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0 ° to 10 ° . 10 Figure 1-3: Tilting the Monitor 0 to 10.
6 Rev.1 Connecting AC Power and Video Cable Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. Figure 1-4: The AC Adapter Power Management System This LCD Monitor complies with the VESA DPMS power management proposal.
7 Rev.1 The Display Controls The LCD Monitor’s Control Panel Figure 2-1: The Control Pane l 1. : Enable the OSD Menu button or / Move the cursor to the left ( w hen OSD is enabled) 2. : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3.
8 Rev.1 Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the Y button causes the screen below to appear. 2. Use the Y & Z key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value.
9 Rev.1 Monitro Adjustment Allow you to adjust the LCD monitor’s display settings. Press the Adjustment control button to display the submenu. Use the Function Select button to select one of the fol.
10 Rev.1 To exits the Monitor-Control submenu OSD-control The OSD-Control menu lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu. OSD-H-POSITION: To change the position of the OSD on a horizontal plane.
11 Rev.1 COLOR: To select the LCD monitor’s color display. The available options are cold, warm and User. Selecting the user option lets you make individual adjustments to the R, G and B items. COLOR R, G and B ADJUST: To make individual adjustments to the Red, Blue, Green (RGB) gain for the color temperat ure.
12 Rev.1 To indicate display mode ti mings and firmware version. EXIT: To exit the Misc-Control submenu. EXIT: Use the OSD Exit item to close the OSD menu.
13 Rev.1 Note: 1) No video When the monitor is ON and there is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out of.
14 Rev.1 Appendix A TFT LCD Monitor Specifications LCD Panel 17" SXGA Control Functions Power Software Power switch with LED indicator (ON/OFF) Main Menu Submenu MONITOR- CONTROL Auto Adjustment,.
15 Rev.1 Scanning Frequency H/V, Hz 24-80K 50-75 P o w e r Management M e e t s VESA DPMS Power Consumption (ON/OFF, W) 35W/1W Max. Dimensions WxHxD 14.
16 Rev.1 Appendix B Supported Timing Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 NEC PC98 640x400 21.05 56.42 24.83 2 MAC 13" mode 640x480 30.24 66.67 35.00 3 MAC 16" mode 832x624 57.
17 Rev.1 Appendix C Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may init ially experience an unstable or unclear display when a new display mode or new VGA card is selected.
18 Rev.1 4. If the power LED is not lit, check that the AC power connector is securely connected, and verify that the AC adapter LED is lit. If the AC adapter LED is not lit, please contact your dealer for assistance. PROBLEM: The LCD displays “signal out of range” error message 1.
デバイスSceptre Technologies X7g-NagaVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sceptre Technologies X7g-NagaVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSceptre Technologies X7g-NagaVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sceptre Technologies X7g-NagaVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sceptre Technologies X7g-NagaVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sceptre Technologies X7g-NagaVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSceptre Technologies X7g-NagaVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sceptre Technologies X7g-NagaVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSceptre Technologies X7g-NagaVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
