Schumacherメーカー10000Aの使用説明書/サービス説明書
ページ先へ移動 of 16
Fully Automatic Microprocessor Controlled Battery Charger with Engine St arter plus Battery T ester CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. 0099000530/0605 OWNER’S MANUAL Schumacher Electric Corporation Mount Prospect, IL 60056 U.
2 PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE EACH USE. Model 10000A, Fully Automatic Battery Charger/T ester and Engine S tarter , offers features to accommodate the needs for home or light commercial use. This manual will explain how to use the battery charger safely and effectively .
3 IMPORT ANT SAFETY INSTRUCTIONS • WARNING: Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.
4 Never place charger directly above battery being charged. The gases from the battery will corrode and damage the charger. Never touch the battery clamps together when the charger is on. You could cause a spark. Never operate charger if it has received a hard blow, been dropped, or otherwise damaged.
5 BEFORE USING YOUR BA TTER Y CHARGER It is important to understand the charger’s requirements. This section explains the charger ’s electrical requirement s and how to prepare a battery for charging. PLUGGING IT IN Y our charger requires a 120V AC receptacle installed according to all local codes and ordinances.
6 OPERA TING INSTRUCTIONS IMPORT ANT : Follow all safety instructions and precautions when charging your battery . Wear complete eye protection and clothing protection. Charge your battery in a well-ventilated area. heavy, unpainted metal part of the chassis or engine block, away from the battery (see figure above).
7 1. Note the polarity of the battery posts by checking the identification marks on the battery: POSITIVE (POS, P or +) and NEGATIVE (NEG, N or -). The positive post is usually larger than the negative post. 2. Attach at least a 24-inch-long, 6- gauge (AWG), insulated battery cable to NEGATIVE (NEG, N or -) battery post.
8 CHARGER CONTROL DISPLAY MODE SWITCH Use this switch to set the function of the digital LED to one of the following. • BATTERY %: The digital LED displays an estimate of the percent of charge of the battery connected to the charger battery clamps. • VOLTAGE: The digital LED displays the voltage at the charger battery clamps in DC volts.
9 CONTROL P ANEL GUIDE 10000A CONTROL PANEL GUIDE MODE OF OPERATION C h a r g e d C h a r g i n g C h e c k B a t t e r y % V o l t a g e 2 A 1 5 A 4 0 A 1 0 0 A S t a r t 1 2 V R e g u l a r 1 2 V D e e p - C y c l e 1 2 V A G M , G e l 6 V R e g u l a r Digital Display Initial power-up, battery not detected O O O 0.
10 USING THE BUIL T -IN BA TTER Y TESTER OVERVIEW This battery charger has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery’s relative charge based on the battery voltage and the Battery Council International scale.
11 OVERVIEW The 10000A has an engine start function that can be used to jump start your vehicle if the battery is low by providing 100 amps of current to assist engine cranking. STARTING SEQUENCE There are a few basic steps involved when using the engine start function.
12 USING YOUR BA TTER Y CHARGER OVERVIEW Using this battery charger is very simple. First, connect the battery and AC power following the precautions listed under “OPERA TING INSTRUCTIONS”. Then select the appropriate BA TTERY TYPE and CHARGE RA TE for your battery .
13 Read this entire manual before using your charger . The tips below serve only as a guide for specific situations. CHARGING TIPS If your vehicle won’t start : Y ou don’t need to fully charge a battery to start your vehicle.
14 BA TTER Y PERCENT AND CHARGE TIME This charger adjusts the charging time in order to charge the battery com- pletely , efficiently and safely . The microprocessor automatically makes the necessary decisions. However , this section includes guidelines that can be used to estimate charging times.
15 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The charger is in tester Press the CHARGE RA TE and the charger is on, mode, not charger mode.
16 LIMITED W ARRANTY SCHUMACHER ELECTRIC CORPORA TION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT , ILLINOIS 60056-2179 MAKES THIS LIMITED W ARRANTY T O THE ORIGINAL PURCHASER A T RET AIL OF THIS PRODUCT .
デバイスSchumacher 10000Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Schumacher 10000Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSchumacher 10000Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Schumacher 10000Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Schumacher 10000Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Schumacher 10000Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSchumacher 10000Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Schumacher 10000Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSchumacher 10000Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。