Searsメーカー113.24611の使用説明書/サービス説明書
ページ先へ移動 of 24
Sears CAUTION: Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS carefu|iy COMMERCIAL 15-I/2 INCH DRILL PRESS assembly operating repair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. and SIMPSONS-SEARS LIMITED, Toronto, Ontario, Canada.
general safely instructions for power tools 1. KNOW YOUR POWER TOOL Read the owner's manual carefully. Learn its application and limitations as well as the specific potential hazards peculiar to this tool. 12. USE SAFETY GOGGLES Safety goggles must comply with ANS Z87.
WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT.TO OPERATE YOUR DRBLL PRESS UNTIL IT IS COMPLETELY ASSEMBLED AND iNSTALLED ACCORDgNG TO THE iNSTRUCTIONS ... AND UNTIL YOU HAVE READ AND UNDERSTAND THE FOLLOWING: 1. General Safety Instructions for PowerTools .
additional safety 11. Note and Follow the Safety Rules that Appear on the Panel on the Left Side of the Head: l DANGER: FOR YOUR OWN SAFETY: READ AND UNDERSTAND OWNERS MANUAL BEFORE OPERATING THIS MACHINE. WEAR SAFETY GOGGLES. DO NOT WEAR GLOVES. SECURELY CLAMP WORK TO TABLE IF IT IS TOO SHORT TO CONTACT THE COLUMN WHEN IN OPERATING POSITION.
motor specifications and eJectricaJ requirements MOTOR SPECIFICATIONS This drill press is designed to use a 1725 RPM motor only. Do not use any motor that runs faster than 1725 RPM. It is wired for operation on 1t0-120 volts, 60 Hz., alternating current.
assembly WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED. 1. Unwind the power cord. 2. Make sure the quill lock handle is tight. 3. Stand on the left side of the drill press and LOOSEN the HEAD LOCK HANDLE.
2. Apply a light film of oil such as Sears household oil to the spindle nose. 3. Place the chuck on the spindle nose and screw the locking collar up as far as it will go. CHUCK 4. 5. Insert a piece of 5/16 in. dia. STEEL ROD in to one of the holes in the chuck body.
assembly INSTALLING THE DEPTH STOP 1. Screw the THUMB SCREW partways into the DEPTH POINTER. 2. Place the DEPTH POINTER SHOE inside the pointer. 3. Loosen QUILL LOCK HANDLE ... lower the quill about two inches. 4. 5. 6. Slide the pointer and shoe onto the FEED STOP ROD and tighten the thumb screw.
9.Gently push down on the FEED HANDLES untilthe head raises upwards as faras it will go. DO NOT RELEASE FEED HANDLE. 10, TIGHTEN THE HEAD LOCK HANDLE AND THE QUILL LOCK HANDLE. 11. HOLD onto the Feed Handle andUNLOCK the quill lock handle. 12. Let the quill return to the UP position in the head, 13.
assembly 4. 5, NOTE: When using motors which have 1/2 in. dia. shafts, place the adapter sleeve (furnished with the motor) on the shaft so that the slot in the sleeve is over the flat spot.
5, Remove the belt guard by "pushing in" on the two "'links". 6. Place motor on drill press ... screw the pivot screws into the holes. NOTE: DO NOT SCREW THEM IN TOO TIGHT ... EXCESSIVE TIGHTNESS COULD BEND THE MOTOR MOUNT. i 7.
assembJy iNSTALLING AND TENSIONING BELT 1. Place a straightedge such as a piece of wood, metal or framing square across the pulleys. 2. Move the motor UPWARDS until the pulleys are IN LINE ... tighten the motor mounting nuts with a ½ in. wrench. 3. Place the belt on the pulleys.
getting tO kr ow SPLINES (GROOVES) SPINDLE QUILL _ RACK (TEETH) CHUCK __-_ CHUCK KEY _ QUILL AND SPINDLE ASSEMBLY INSIDE OF DRILL PRESS SPINDLE SPEED CHART 9 CHUCK KEY ... is used to tighten or loosen the chuck. It has a spring loaded EJECTOR pin to "pop'" it out of the chuck when you let go of it.
getting to know your drill press To turn drill ON .. Insert finger under switch lever and pull. TO turn drill OFF ... Push lever in. In an emergency; ...thedrill bit BINDS ...STALLS .. STOPS . .. or tends to tear the workpiece loose . .. you can QUICKLY turn the drill OFF by hitting the switch with the palm of your hand.
_{_ The DEPTH POINTER is locked in place with the THUMBSCREW. !_ L FEED STOP NUT limits the downward movement of the quill at any desired point within its travel, and prevents the pointer from moving upward. DR! LLING TO DEPTH To drill a BLIND hole (not all the way through) to a given depth, can be done two ways.
basic drill press operation INSTALLING DRILLS Insert drill into chuck far enough to obtain maximum GRIPPING of the CHUCK JAWS ... the jaws are appox. 1 in. long. When using a small drill do not insert it so far that the jaws touch the flutes (spiral grooves) of the drill.
diustments WARNeNG: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS. DEPTH SCALE When the quill is in the UPPERMOST position, the top SURFACE OF THE FEED STOP POINTER should be in line with "0" graduation on the DEPTH SCALE.
adiustments 5. LOOSEN all three screws "C", "D", and "E'" four turns using 1/4 in. setscrew wrench. NOTE: TIGHTENING BOTH SCREWS "C'" AND "E'" SQUEEZES HEAD TOGETHER ... TIGHTENING SCREW "'D" SPREADS IT APART.
trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTaNG. TROUBLE Noisy Operation Drill Burns. Drill leads off... I hole not round. t Wood splinters on underside.
6O PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.2461! 68 30 64 T_IO 1 8 13 14 SEE FIGURE 2 11 12 I J ALL WIRES TO SNAP INTO WIRE SADDLE _ I--.83 _.
Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 78 79 :0 7 2 3 4 5 6 7 8 9 0 1 2 3 4 Part No. 70197 STD 541110 71046 STD 571812 71163 STD 551210 STD 551208 STD 600605 7.
PARTS LIST FOR CRAFTSMAN COMMERCIAL DRILL PRESS S MODEL No. 113.24611 . . __ FIGURE 2 PARTS LIST Key Part No. No. ,_, r = 71128 12 144987 4 71069 5 STD 610807 13 6 60158 7 71071 8 71070 71162 1_] 71072 14 11 71097 12 60227 13 71089 11_ 14 71090 15 STD 315253 15---"--_ 16 71091 16.
/ / / / t PARTS LIST FOR CRAFTSMAN COMMERCIAL DRILL PRESS MODEL No. 113.24611 / / / ,/ / / 1, / / / / / 10---_ 11 / FIGURE 3 -- 71158 SPINDLE ASM. STOP PARTS LIST Key Part No.
Sears SERVICE MODEL NO. 113.24611 HOW' TO ORDER REPAIR PARTS COMMERCIAL 15-1/2 INCH DRILL PRESS Now that you have purchased your drill press, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
デバイスSears 113.24611の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 113.24611をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 113.24611の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 113.24611の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 113.24611で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 113.24611を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 113.24611の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 113.24611に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 113.24611デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。