Searsメーカー149.213340の使用説明書/サービス説明書
ページ先へ移動 of 16
SERIAL OR CODE NUMBER: Model and code number may be found on1he right side of Spindie Housing You should record both model and serial number and retain in a satepiace for future use CALIFORNIA OWNERS: a unique serial code number is stamped inside the Pulley Cover CAUTION: Read All Instructions Carefully Before Start- ing Assembly and Use.
FULL ONE-YEAR WARRANTY ON CRAFTSMAN RADIAL DRILL PRESS If within one year from date of purchase, this Craftsman RADIAL DRILL PRESS fails due to a defect in materi- al or workmanship, Sears will repair it, free of charge WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER IN THE UNITED STATES, .
4 REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see thatkeys and adjusting wrenches are removed from tool before turning on 5 KEEP WORK AREA CLEAN Cluttered areas and beeches invite acc.
SAFETY RULES FOR DRILL PRESSES 1 DO NOT USE until unit is completely assembled and installed according to instructions 2 USE ONLY CHUCK KEY PROVIDED WiTH YOUR RADIAL DRILL PRESS It is equipped with a .
TOOLS REQUmRED 8-inch Adjustable Mallet Wrench UNPACKRNG AND CHECKUNG CONTENTS Model 149213340 Radial Drill Press is shipped complete in one carton Carefully unpack and separate parts from packing mat.
ASSEMBLY WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT THE RADIAL DRILL PRESS TO A POWER SOURCE UNTIL ALL ASSEMBLY STEPS ARE COMPLETE_ AND YOU HAVE READ AND UNDERSTOOD SAFETY AND OPERATIONAL INSTRUCTION.
I 7 Make sure bottom of Spindle Shaft (REF 42) and bore of Chuck (REF 46) are clean and free of grease Press Chuck up onto Spindle Shaft_ NOTE: To avoid damage to Chuck, rotate Chuck barrel until jaws are fully open.
CONTROLS AND ADJUSTMENTS _ WARNING: MAKE SURE SWITCH IS IN OFF POSmON AND POWER CORD IS UNPLUGGED BEFORE PERFORMING CHECKS= ADJUSTMENTS I OR SETUP PROCEDURES, On-Off Switch 2.
I Cast Tab Spring Assembly /_ ))_ Feed Shaf< _ ) Lock'Nuts 3 Check operation of Return Spring for proper tension and full return 4 Nuts must be tightened before use Be very careful; the nuts h.
Belt Tension Butterfly Set Screw Angle Gauge (REF 85) on Column head and full length scored V groove on Horizontal Tube (REF 81) to set desired angle Lock in position using Lock Handle When returning .
Adjusting Spindle Perpendicular to Table The Radial Drill Press was factory-adjusted and set with Spindle Housing perpendicular to table No further adjust- ment should be necessary However.
OPERATaON Correct Drilling Speeds See "Changing Speeds" section under "Controls and Adjustments" and Speed Chart inside Pulley Cover for cor- rect drilling speeds Always disconnect.
ACCESSORUES Mortising Kit Vises and Clamps Although not designed specifically for mortising, the variety of possible drill angles and feed lengths with the Radial Drill Press make possible some former.
CRAFTSMAN 344NCH RADIAL DRILL PRESS MODEL No. 149.213340 REPAnR PARTS 72 71 7 14 ---i 87 14/__ 6 12 17 5 J 4 I I 88 15 3 53 30 29 89 : 34 54 14.
CRAFTSMAN 34-iNCH RADIAL DRULL PRESS MODEL No. 149.213340 PARTS LIST REF NO, 1 2 3 4 8 6 7 8 9 10 11 12 !3 14 15 18 17 18 !9 2O 21 22 23 24 25 281 27 28 29 30 31 32 33 34 35 36 37 3R 39 4O 41 42 43 44 45 46 46A 47 48 49 5O PART NO.
TROUBLESHOOTING CHART TROUBLE PROBABLE CAUSE REMEDY Noisy operation 1 Incorrect V-belt tension 1_ Adjust tension 2 Dry spindle shaft 2. Lubricate spindle shaft See "Maintenance" section 3 Loose Spindle shaft or 3 Tighten Lock Nut (left hand thread) or pulley Motor Pulley set screw, Bit burns or smokes 1 Incorrect spindle speed.
デバイスSears 149.213340の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sears 149.213340をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 149.213340の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 149.213340の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 149.213340で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 149.213340を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 149.213340の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 149.213340に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 149.213340デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
