Searsメーカー200.71226の使用説明書/サービス説明書
ページ先へ移動 of 16
OWNER'S MANUAL Microprocessor Controlled, Fully Automatic Operation Battery Charger with Engine Starter Plus Battery and Alternator Tester 2=AIVlP SLOW CHARGE 15=AMP FAST CHARGE 40-AMP RAPID CHARGE 125=AMP ENGINE START FOR 12=VOLT BATTERIES Model No.
WARRANTY ................................................................................................................ 2 IMPORTANT SAFETY INSTRUCTIONS ................................................................... 3 PERSONAL SAFETY PRECAUTIONS .
WARNING = RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT- TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Never place charger directly above battery being charged. The gases from the battery wilt corrode and damage the charger. Never touch the battery clamps together when the charger is on. You could cause a spark. Never operate charger ifit has received a hard blow, been dropped, or otherwise damaged.
PLUGGING IT IN Your charger requires a 120V AC 2-prong wall outlet receptacle installed according toalllocal codes and ordinances. It is important tounderstand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery forcharging.
NOTE: A marine (boat) boat battery must be removed and charged on shore. To charge it on board requires equipment specially designed formarine use. IMPORTANT: Follow all safety instructions and precautions when charging your bat- tery. Wear complete eye protection and clothing protection.
CHARGING BATTERY REMOVED FROM THE VEHICLE: POSITIVE NEGATIVE BATTERY BATTERY _CHARGER POWER 24", 6 GAUGE CABLE GROUNDED POWER OUTLET 1. Note the polarity of the battery posts by checking the identification marks on the battery: POSITIVE (POS, P or +) and NEGATIVE (NEG, N or-).
in seconds. It starts at 5 and counts down to 0. 3. Cool Down - After cranking, the char- ger enters a mandatory 3-minute (180 second) cool down state. During this period, no settings can be changed. The buttons are ignored. The digital display indicates the remaining cool down time in seconds.
If the charge mode is changed after charg- ing has started (by pressing the CHARGE RATE or CHARGE TYPE button), the charging process wilt berestarted. The voltage displayed during charging is the charging voltage and usually will be higher than the battery's resting voltage.
71226 CONTROL PANEL GUIDE MODE OF OPERATION Initial power-up, battery not detected No battery or reversed battery detected Battery tester activated Battery tester with charged battery Battery tester w.
OVERVIEW This battery charger has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery's relative charge based on the battery voltage and the Battery Council International scale. TESTING SEQUENCE There are four basic steps required to use the 71226 as a battery tester.
This battery charger has a built-in alter- nator tester that displays either an accu- rate alternator voltage or an estimate of the alternator's relative output compared tonormal alternators. The Alternator % values displayed should be taken as general reference, not precise diagnosis.
This charger adjusts the charging time in order to charge the battery completely, efficiently and safely. The microproces- sor automatically makes the necessary decisions. However, this section includes guidelines that can be used to estimate charging times.
Read this entire manual before using your charger. The tips below serve only as a guide for specific situations. If your vehicle won't start: You don't need to fully charge a battery to start your vehicle.
Performance problems often can be corrected by the user. Please read through this chart for a possible solution to common problems. PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The charger is in tester and the charger is on, mode, not charger mode.
This section shows an illustration of your battery charger. Use it to become familiar with part locations and appearance. Replacement Parts List Sears 71226 iTEM DESCRIPTION PART NUMBER 1 Handle Assem.
デバイスSears 200.71226の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 200.71226をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 200.71226の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 200.71226の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 200.71226で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 200.71226を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 200.71226の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 200.71226に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 200.71226デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。