Searsメーカー315.10186の使用説明書/サービス説明書
ページ先へ移動 of 21
Operator's Manual 3/8 in. (10 mm) CORDLESS DRILL-DRIVER Vadable Speed / Reversible Model No. 315.101860 - 14.4 Volt Save this manual for future reference ,_ WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product.
• Warranty ........................................................................................................................................................................... 2 I Introduction .................................................
_i WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS, Failure to follow all instruCtions listed below, may result in electric shock, fire and/or seriouspersonal iniury. SAVE THESE INSTRUCTIONS WORKAREA • Keep your work area clean and well lit. Cluttered benches and dark areas Invite accidents.
SERVICE • Tool service must be performed only by qualified repair personnel. Service or maintenancepedormed by unqualifiedpersonnel couldresult in e risk of injury. • When servlclng s tool, use only identical replace- ment parts. Follow Instructions In the Maintenance section of this manuel.
,A WARNINGI READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to followall Instructions listed below, may re.suit in etect_ shock, fire and/or serious personal injury.
i Important: Some of the following symbols may be used on this tool. Please studythem and learn their meaning. Proper Interpretation of these symbols will allow you to operate the tool better and safer.
PRODUCT SPECIFICATIONS Chuck ........................................... 3/8 in. (10 ram) Keyless Motor .............................................................. 14.4 Volt DC Switch ....................................................... Vadab[e Speed Gear Train .
TORQUE ADJUSTMENT RING KEYLES8 CHUCK BIT STORAGE CHARQER ASSEMBLY TRIGOER ROTATION SELECTOR (FORWARD/REVERSE) BAI-r ERY Fig. 1 INSTRUCTIONS When unpacking the tool: • Carefully remove the tool and accassodes from the box. • Make sure that all items listed in the packing list are in- cluded.
WARNING: Do not allow familiarity with your drill- df',ver to make you careless. Remember that a careless fraction of a second is sufficient to _nffict severe Injury. CHARGING YOUR DRILL-DRIVER The battery pack for this tool has been shipped In e low charge condition to prevent passible problems.
BATrERT PACK BATrlERY PORT To stop, release switchtrigger and allow the chuck to come to a complete stop. _1= WARNING: Battery tools ere always in operating cond_on. Therefore, switch should always be locked when not In use or when cerwIng at your side.
SCREW'DRIVING TORQUE ADJUSTMENT (Driving power of your drill-driver) When using your drill-driver for varlous driving applica- tions, it becomes necessary to increase or decrease the torque in order to help prevent the possibility of damaging screw heads, threads, workplace, etc.
INSTALLING BITS • Place the direction of rotation celector in center position. See Figure 5. This will turn off the power to your drill. • Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
_1= WARNING: Always wear safety goggles or safety glasses with side shields when operatingtool, Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury, DRILLING See Figure 11. When drillinghard, smooth surfaces, usa a canter punch to mark the desired hole Iocallon.
CHUCK REMOVAL See Figures 12 - 14. • Lockthe swiLch trigger by plscing the direction of retation selector in center position. See Figure 5. • Insert a 5/15 inch or larger hex kay Into the chuck of your ddtt and [_ghten the chuck jews sscumly. • Tap the hax key sharply with a mallet in a clockwise direction.
_lb WARNING: When servicing, use only identical Craftsman replacement perts. Use of any other pert may create a hazard or cause product damage. Do not abuse power tools.
16.
COMPANION 14.4 VOLT CORDLESS DRILL MODEL NO, 315.101860 I The model number will be found on a plate attached to the motor housing. Always mention the model ] number in all correspondenceregarding your.
COMPANION 3/8 In. 14.4VOLT CORDLESS DRILL-DRIVER - MODEL NUMBER 315.101860 14 %, : 9 15 13 10 11 P 12 _ 14 6 8 7 5 3 4 2 1.
COMPANION 3/8 In. 14.4 VOLT CORDLESS DRILL-DRIVER - MODEL NUMBER 315.101860 The model number will be found on a plate attached to re motor housing. Always mention the model number In all correspondenceregarding your | | CORDLESS DRILL-DRIVER or when ordering repair parts.
COMPANION 3/8 In. 14.4 VOLT CORDLESS DRILL-DRIVER - MODEL NUMBER 315.101860 BLUE LEAD RED LEAD BLACK LEAD RED BLACK LEAD BLACK LEAD HEAT SINK WIRING DIAGRAM.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it] For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
デバイスSears 315.10186の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sears 315.10186をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears 315.10186の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears 315.10186の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears 315.10186で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears 315.10186を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears 315.10186の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears 315.10186に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears 315.10186デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。