SearsメーカーDieHard 200.71460の使用説明書/サービス説明書
ページ先へ移動 of 15
SEA/RS OWNER'S MANUAL Model No. 200.71460 CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product. h__ 60/20/2 AMP MANUAL BATTERY CHARGER 250/125 AMP ENGINE STARTER with BATTERY TESTER Sears, Roebuck and Co.
Table Of Contents Warranty .................................................................. 1 Important Safety Instructions .................................. 2 Parts ......................................................................... 3 Before Using Your Battery Charger .
Important Safety Instructions - SAVE THESE INSTRUCTIONS - • Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. • Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, trac- tors, airplanes, vans, RV's, trolling motors, etc.
Parts The exploded view of your charger shows parts, their location, and a keyed chart identifying each part by name and pert number. The wiring diagram provides additional reference for the professional repair person.
Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.
3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded.
Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
VOLTMETER: For an accurate reading of your battery's voltage before you begin charging it, use the voltmeter as follows: 1. Set the timer to the OFF position, turn the voltage selector switch to .
Charging Your Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads care- fully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear ofthe fan blades, belts, pulleys, and other parts that can cause injury.
11. When the battery is fully charged, first unplug the charger's powercord. Next, turn thetimerswitch to the OFF position. Then, standing away from the battery, remove the charger clamps in this order: (1) from the chassis connection and, (2) from the battery post.
Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries-- motorcycles, garden tractors, etc.
Using the engine start feature Your battery charger can be used to jump-start your car if the battery is low. Follow these instructions on how to use the engine start feature.
Troubleshooting Performance problems often result from little things that you can fix yourself. Please read through this chart for a )ossible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check for poor connections to battery and frame.
SEAR8 OWNER'S MANUAL Model No. 200.71460 When requesting service or ordering parts, always provide the following information: • Product Type • Model Number • Part Number • Part Descriptio.
デバイスSears DieHard 200.71460の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sears DieHard 200.71460をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSears DieHard 200.71460の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sears DieHard 200.71460の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sears DieHard 200.71460で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sears DieHard 200.71460を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSears DieHard 200.71460の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sears DieHard 200.71460に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSears DieHard 200.71460デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
