Security 100メーカーKE-265の使用説明書/サービス説明書
ページ先へ移動 of 14
KE-265 Keyless Entry Access Control System Installation and Operations Manual.
Table of Contents ESSEX ELECTRONICS, INC. INTRODUCTION ....................................................................................... 2 KE-265 Series O VERVIEW ..................................................................................
Introduction Input Requirements The KE-265 accepts 12 to 24 volts AC/DC. An optional battery charging module and rechargeable Gel Cells are available to keep the system operational for up to 24 hours during a power interruption.
Prep aring for Inst allation Keypad Options All Essex Keypads are designed to perform reliably in even the most extreme environmental conditions. Operating temperatures can range from -40 ° C to +70 ° C (-40 ° F to 160 ° F).
The Inst allation Procedure 6. Do NOT mount Keypad at this time. 7. Proceed to Install the Wiring Cable. Required Tools Mounting Instructions 12 Pad 3x4: KP-34S, KP-34B or KP-34K You will need the following tools: The 3x4 keypad is designed to mount to a single gang switchbox or on a wall, pedestal or any flat surface of at least 3 ½ by 5 ¼”.
Install the Wiring Cable 1. Drill a ½” hole in the inside wall or ceiling where you want the cable to come through. 2. Pull the cable through the hole so the connector end goes to the keypad.
System Hardware Setup The Factory Default Settings are shown here: Remote By-Pass 1. All User Unlock Authorization is configured for Relay #1. (Master Code and Users 1,2 and Users 3,4,5). Factory Default Settings In some cases, it may be necessary to control the door from a remote area such as a security station or reception desk.
12 Latching Authorization Placing jumpers across the 4 th and 5 th set of pins (1,2 LATCH or 3,4,5 LATCH) determines which relay (if any) each User Group is authorized to manually latch.
14 System Programming Overview of System Code Programming There are TWO levels of codes for the KE-265 system. 1. The Master Code (used to open the door and for programming User Codes) 2. User Codes (used by personnel to open the door) IMPORTANT: Notes to remember before programming: 1.
16 Programming User Codes To Program a New User Code or Change an Existing User Code: 1. Choose a new 3 to 8 digit code that will be used for this User Code. ___ ___ ___ ___ ___ ___ ___ ___ 2. Decide which User Location to place this User Code (see Overview of User Codes) 3.
18 T roubleshooting These are a few troubleshooting suggestions to help assist with any problems you may experience. If the problem continues or is not answered here, please call Essex technical support at (800) KEYLESS Î (800) 539-5377. You can also visit Essex anytime at keyless.
20 Keypad beeps all by itself Constant Beeping - If the beep is consistently every 5 seconds, put a . 1 uf 16v (or higher) ceramic capacitor across wires 3 & 10 (black, violet) on terminal strip “A”. Random Beeping - Check for bad circuit ground going to the keypad.
22 23 Appendix A – Circuit Board Layout Upon receipt of such notification, Esse x Electronics, Incorporated w ill determine whether to repair or replace. We also re serve the right to hav e our representative make any inspection or repairs, or furnish replacements.
Appendix B- T ypical Wiring Diagrams Notes Note: Some low current strikes or relays w ill cause relay chatter due to inductive kickback. Attach MOV across st rike or relay to eliminate chatter.
デバイスSecurity 100 KE-265の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Security 100 KE-265をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSecurity 100 KE-265の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Security 100 KE-265の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Security 100 KE-265で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Security 100 KE-265を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSecurity 100 KE-265の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Security 100 KE-265に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSecurity 100 KE-265デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
