SharkRackメーカー37Uの使用説明書/サービス説明書
ページ先へ移動 of 46
ID-00210-000 Enclosure Installation Guide 37U Cabinet (37”DP / 42”DP) 42U Cabinet (37”DP / 42”DP) 45U Cabinet (37”DP / 42”DP) ID-00210-000 REV D, ECO2773 Page 1 of 46 Proprietary Information of SharkRack, Inc. 32920 Alvarado-Niles Rd Suite 250, Union City, CA 94587 510-477-7900 • 510-324-1664 • www.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 2 of 46 Table of Contents Table of Contents .............................................................................................................. ........ 2 Introduc tion .
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 3 of 46 Introduction Thank you for buying a SharkRack computer c abinet. The SharkRack family of computer cabinets has been designed with great care and made with the highest quality materials to provide you with many years of satisfactory use.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 4 of 46 Symbols in Text WARNING: Text set off in this manner indica tes that fa ilure to follow directions in the warning could result in bodily harm or loss of life.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 5 of 46 WARNING (CONT.): Plug cabinet power cords into electrical outlets that are locat ed near the cabinet and are easily accessible. Connect all devices installed in a rack to power devices inst alled in the same cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 6 of 46 Chapter 1 Site Preparation Check Facility Provisions Ensure that the following conditions are met: • Floor is level and of sufficient strength to support the rack and your equipment.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 7 of 46 Rack Cabinet Footprint and Mounting Locations for: Cabinet with Full Rear and Front Doors Figure 3 42U X 37DP (TOP VIEW).
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 8 of 46 Rack Cabinet Footprint and Mounting Locations for: Cabinet with Split Rear Door Figure 4 42U X 37DP (TOP VIEW) and 42U X.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 9 of 46 Chapter 2 Receiving and Unpacking Check package and receiving area • Verify contents and condition. • Move the packaged cabinet on its pallet as close to its final d estination as possible.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 10 of 46 Unpacking Instructions- Standard Packaging Step Detail Note: Unpacking of a cabinet requir es at least two people. There must be at least 7 feet of clear area in front of the loaded pallet to unload the cabin et.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 11 of 46 Step Detail CAUTION: Be sure the leveling feet are fully raised to prevent accidental tipping.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 12 of 46 Unpacking Instructions- Integration Packaging Step Detail WARNING: A fully loaded cabinet is very heavy. Take proper preca utio ns when moving the cabinet Note: Unpacking of a cabinet requir es at least two people.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 13 of 46 Unpacking Instructions- Integration Packaging (cont.) Step Detail CAUTION: Be sure the leveling feet are fully raised to prevent accidental tipping. (See Figure 7 for details.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 14 of 46 Chapter 3 Configure Accessories into the Cabinet Configure Optional Accessories The SharkRack cabinet can be configured using multiple optional accessories. The configuration depends on your specific application and may vary from cabinet to cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 15 of 46 Installing and Removing Doors Step Detail To remove doors: 1. Open the door. 2. Pull down on the spring- loaded hinge pin attached to the top of the door. 3. Move top of door away from enclosure and lift the bottom of door up from the cabinet and set aside.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 16 of 46 Installing and Removing Doors (cont.) Step Detail To install doors: 1. Align the lower door hinge pin with the hole in the bottom hinge bracket and slide the h in ge pin into the hole.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 17 of 46 Door Handles Step Detail Remove door handle: To enhance your cabinet, Sha rkRack offers an optional line of electronic door hand les which use HID or keypad entry. These locks can be networked together for remote management and access tracking.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 18 of 46 How to Reverse the Door Swing Step Detail Reverse the door handle: 1. Open the door. 2. Rotate the handle to align the cam po inting down. 3. Use a screwdriver to push the snaps inward.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 19 of 46 Step Detail Reverse the door hinge brackets: 4. Remove the door. (See “Installing and Removing Doors” on page 15) 5. Use a Phillips head screwdriver to remove the hinge pin brackets and latch b r acket(s) from the cabinet frame.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 20 of 46 How to Reverse the Door Swing (cont.) Step Detail 6. Reinstall the hinge pin brac kets and latc h bracket(s) on the opposite side of the cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 21 of 46 Adjusting the Leveling Feet Step Detail The leveling feet help stabil ize the cabinet and keep the cabinet level on une ven floors. This should be done before you in stall products into the cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 22 of 46 Installing the Retractable Tip Guard Step Detail The Retractable T ip Guar d should be used when the cabinet is not secured to the floor and equip ment is being slid in and out of the cabine t.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 23 of 46 Installing the Floor Mounting Brackets Step Detail The Floor Mounting Brackets should b e used when sliding equipment in and out of the cabinet and no other stabilizing provis ions are in place.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 24 of 46 Adjusting or Replacing the Mounting Rails Step Detail Adjusting the mounting rails: The mounting rails are factor y set at 29.12 inches apart. However, both the front and rear mounting rails are adjustable to any de pth within the cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 25 of 46 How to Remove or Install a Top Panel Step Detail The Top Panel can be remov ed. To remove a Top Panel: 1. Unlock the Top Panel using the ke y. 2. With the key turned in the unlocked p ositio n, lift up until you can grab the top p anel with your free hand.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 26 of 46 How to Remove or Install Side Panels Step Detail The Side Panels can be remo ved to provide further access to equipment mounted inside the cabinet. This is a great way to get added access for cable management or installing powerstrips.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 27 of 46 Installing a Grounding Kit Step Detail Grounding points are provided on the vari ous cabinet components so that each component can be electric ally bonded to the frame. Detail A: Shows how to route the grounding cables thr ough the frame of the cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 28 of 46 Using the SharkTRAC™ and SharkSNAP™ Step Detail The SharkTRAC™ is a patent pending platform consisting of a series of holes, which allows attachment of various devices.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 29 of 46 Installing a Typical 19 inch EIA Power Strip Step Detail 1. Secure to the Cabinet Mounting Rails 1a. (As required) Install 10-32 cage nuts. Some mounting rails require the use of cage nuts; install them into the appropriate holes as sho wn.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 30 of 46 Installing a Typical 19 inch EIA Power Strip (cont.) Step Detail 2. Secure to the SharkTRAC™ using SharkSNAP™ Brackets Note: There must be two SharkSNAP™ brac kets install ed which allows a power strip to clip in-bet ween them.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 31 of 46 Installing a Typical 19 inch EIA Power Strip (cont.) Step Detail 3. Secure to the SharkTRAC™ using screws 3a. Install 10-32 cage nuts. The SharkTRAC™ requir es the use of cage nuts; install them into the appropriate holes using the method shown.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 32 of 46 Cable Management Step Detail The SharkRack cabinet has b een d esigned with integrated cable managem ent. There are numerous provisions for running cab les in the corner posts of the frame as well as out the top, bottom, in both the front and back of the cabinet.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 33 of 46 Installing a MultiBay Kit Step Detail MultiBay kits are used to group t wo or more SharkRack cabinets together. MultiBay kits can be installed prior to installing computer equipment into the rack cabinet or after equipment is already l oad ed.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 34 of 46 Chapter 4 Install Computer Equipment To install computer equipment into the cabinet: • Plan component locations in the cabinet. • Install computer equipment. • Route and secure all loose cables accordingly.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 35 of 46 Cabinet settings for various manufacturers’ devices (cont.) IBM™ • Most IBM rack mountable products use a 3/8” square-holed “L”-style mounting rails. • Typically products use 10-32 cage nuts and screws.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 36 of 46 Chapter 5 Final Assembly Check for Functionality • Have a qualified electrician verify the power sources for your specified power requirements. • Check that there is no obstruction to any device that needs to be accessed for maintenance.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 37 of 46 Appendix A: Glossary EIA: For more than 72 years the Electronic Industries Alliance has been the national trade organization representing U.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 38 of 46 Appendix A: Glossary (cont.) Cage Nut: A fastener typically used in square-hole universal type racks, similar to a Clip Nut. When selecting the correct cage nut you must specify the thread size as well as the thickn ess of the mounting rail they will be attaching to.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 39 of 46 Appendix A: Glossary (cont.) SharkTRAC™: The SharkTRAC™ is a platform consisting of a series of holes, which allows attachment of various devices such as the family of SharkSNAP™ tool-less clip-in devices.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 40 of 46 Appendix B: Basic Cabinet Components Note: Before you begin co nfigurin g your SharkRack cabine t, it is best to verify that you have received all necessary items to begin your installation.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 41 of 46 Table 1 Parts List Parts List REF Description Quantity/REF A Cabinet Frame 1 B Front Door Kit Grommet Bumper 2 Bracket,.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 42 of 46 Appendix C: Cabinet Specifications Note: The information listed on the chart in Table 2 is taken from SharkRack’s latest generation of racks. Previous generations vary from that listed bellow.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 43 of 46 Cabinet Dimensions (Top View) Figure 45 Cabinet Dimensions.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 44 of 46 Mounting Rail Dimensions (Front View) Figure 46 Mounting Rails.
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 45 of 46 Figure 1 ....................................................................................................................... .........................................
SharkRack Enclosure Installation Guide ID-00210-000 REV D, ECO2773 Page 46 of 46 Warranty LIMITED WARRANTY AND WA RRANTY DISCLA IM ER - Seller warrants that the System will be free from defect s in materials and workmanship for a p eriod of one (1) year from date of deliver y to customer premises.
デバイスSharkRack 37Uの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
SharkRack 37Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSharkRack 37Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。SharkRack 37Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。SharkRack 37Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
SharkRack 37Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSharkRack 37Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、SharkRack 37Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSharkRack 37Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。