SharpメーカーFO-2150CMの使用説明書/サービス説明書
ページ先へ移動 of 26
1 - 1 UX-2200CMU/CMC FO-2150CMU/CMC F ACSIMILE INK JET PRINTER UX-2200CM MODEL FO-2150CM No. 00ZU220CMUTME TECHNICAL MANUAL Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
UX-2200CMU/CMC FO-2150CMU/CMC – 1 – [1] Engine Specifications 1. Mechanism Resolution : 600 dpi x 600 dpi addressability Print Speed : 3 PPM draft text with black cartridge Print Swath : 8 inches Duty Cycle : Up to 500 pages per month maximum, 170 pages per month average Dimensions (approximate) : 350mm x 125mm x 60mm Weight (approximate) : 1.
UX-2200CMU/CMC FO-2150CMU/CMC [4] Circuit description 1. General description The compact design of printer PWB is obtained by using 8 bit microprocessor(CPU) and ASIC in the printer control section. 2. Electrical System The PWB provides mechanical control for Ink Jet Printer .
UX-2200CMU/CMC FO-2150CMU/CMC 3. Electricai Overview The information in this section appears in a sequence relative to the system diagram in the following figure. 4. Power Supply Connector The mechanism requires two voltages (+5V and +24V). These two voltages supplied from CNPR T connector.
UX-2200CMU/CMC FO-2150CMU/CMC 7. Driver IC The paper motor and carriage motor require current that cannot be driven directly from ASIC chip. Motor driver IC provide the additional current and voltage capability . The driver IC (IC1 and IC2) located near the respective motor connector on the printer PWB also connect back to the ASIC.
UX-2200CMU/CMC FO-2150CMU/CMC 9. Carriage Motor The ASIC controls the carriage motor , which is a stepping motor that connects via a 4-pin connector to CN2 on the printer PWB. 10. INK Cartridge Carriage The carriage connects via a flex circuit that plugs into the 32 pin connectors, CN3 and CN4 on the printer PWB.
UX-2200CMU/CMC FO-2150CMU/CMC – 6 – 12. Home Position Sensor LEFT RIGHT CARRIAGE HOLDER A B C The home position of carriage is detected as a result of change of output of photointurrupter A which is caused due to shutting-off of optical path of photointerrupter A by the slit B .
UX-2200CMU/CMC FO-2150CMU/CMC [5] Overall T rouble Shooting Of Printer PWB FRONT VIEW B C E Q1 FRONT VIEW BE C Q101 Figure 1 Figure 2 – 7 – NG NG • BOTH CARRIAGE MOTOR AND FEED MOTOR ARE NG.
UX-2200CMU/CMC FO-2150CMU/CMC CHECK WAVEFORMS IC2 ( 3,5,7,9 pin) (Figure 3) REPLACE PRINTER PWB FUSE “F101” Check the laser diode driver. OPEN OK OK OK CHECK WAVEFORMS IC2 ( 2,4,6,8 pin) (Figure 4.
UX-2200CMU/CMC FO-2150CMU/CMC MISSING MANY NOZZLES CLEAN NOZZLES NG NG YES REPLACE ANOTHER CARTRIDGE NO • MISSING NOZZLES (RESULT OF CHECK PATTERN OR CLEAN NOZZLES CHECK +24 PATTERN CHECK IC AND CON.
UX-2200CMU/CMC FO-2150CMU/CMC [6]How to Decide the Number of the Wrong Nozzle FUNC + 6 + + “CLEAN NOZZLES” A B Nozzle 1 Nozzle 56 Horizontal lines on A and B correspond to nozzle #1,#2 .... #56 from left side to right side. If there are missing horizontal lines, you can decide the number of wrong nozzle from pattern A or B .
UX-2200CMU/CMC FO-2150CMU/CMC Nozzle# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 IC 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 PIN 39 39 35 35 31 31 25 25 .
UX-2200CMU/CMC FO-2150CMU/CMC 2ms / d CN1-2 CN1-3 CN1-4 CN1-5 CH1=50V DC P:10 T:1.92ms Stopped CH2=50V DC P:10 1/ T:520.8Hz CH3=50V DC P:10 CH4=50V DC P:10 T 1 2 3 4 G G G G G : 0V [7] W aveforms FEED.
UX-2200CMU/CMC FO-2150CMU/CMC CARRIAGE MOT OR W A VEFORMS – 13 – Figure 2 20s / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:19.2¨s Stopped CH2=20V DC P:10 1/ T:52.08kHz CH3=20V DC P:10 CH4=20V DC P:10 T 1 2 3 4 When the cartridge holder is at the position of replacing cartridge.
UX-2200CMU/CMC FO-2150CMU/CMC CARRIAGE MOTOR W A VEFORMS MEASURED FOR CHECKING OUT OF INK 2ms / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:1.92¨ms Stopped CH2=20V DC P:10 1/ T:520.8Hz CH3=20V DC P:10 CH4=20V DC P:10 T 1 2 3 4 500s / d CN2-1 CN2-2 CN2-3 CN2-4 CH1=20V DC P:10 T:480¨s Stopped CH2=20V DC P:10 1/ T:2.
UX-2200CMU/CMC FO-2150CMU/CMC Action Check the motor for binds,or loose motor pulley . T urn the printer off and disconnect CN2 from the system board.Check for motor pins shorted to the motor housing.If you find a pin shorted to the housing,replace the motor .
UX-2200CMU/CMC FO-2150CMU/CMC FRU Envelope Guide Action Be sure the envelope guide has been turned to the envelope load position. Be sure the envelope guide is against the envelopes.
UX-2200CMU/CMC FO-2150CMU/CMC FRU System Board Paper Feed Motor Drive T rain Assembly Auto Sheet Feeder Mid-Frame Asm Access Cover Asm End-of-Forms Flag and Spring End-of-Forms Sensor Action T urn the printer on and verify the paper feed motor activates.
UX-2200CMU/CMC FO-2150CMU/CMC 5. Paper Path Service Check Examine the machine for the following before you being this service check: • Check the entire paper path for obstructions • Be sure the correct type of paper is being used. • Be sure the printer is installed on a flat surface.
UX-2200CMU/CMC FO-2150CMU/CMC – 19 – [9] IC Signal Name IC 8 : VHiTMP87PH47U (TMP87C807U) 1. Pin Assignment (T op View) 2. Block Diagram 34 35 36 37 38 39 40 41 42 43 44 22 21 20 19 18 17 16 15 14 13 12 33 32 31 30 29 28 27 26 25 24 23 P63 P62 P61 P60 N.
UX-2200CMU/CMC FO-2150CMU/CMC P07 to P00 I/O P17,P16 I/O P15(TC2) I/O(Input) P14(PPG) I/O(Output) P13(OVO) P12(INT2/TC1) I/O(Input) P1 1(INT1) P10(INT0) P22(XTOUT) I/O(Output) P21(XTIN) I/O(Input) P20.
UX-2200CMU/CMC FO-2150CMU/CMC – 21 – IC 4 , 6 : VHil6451///-1 (L6451) 1. Pin Connection (T op View) 2. Block Diagram (case of 4 bit) 6 5 4 3 2 1 44 43 42 41 40 OUT 27 CHIP ENABLE COM 2 GND LOGIC SUPPLY IN D IN C IN B GND IN A COM 1 OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 OUT 8 OUT 9 GND N.
UX-2200CMU/CMC FO-2150CMU/CMC Name Function VDD 5V Logic Supply . GND Logic and Power Ground. OUT0 to OUT27 DMOS Output. CLAMP This pin has to be connected to the power supply voltage of the head resistors.
UX-2200CMU/CMC FO-2150CMU/CMC [10] Exploded V iew a a 26 14 37 45 54 56 56 55 11 15 16 18 17 36 25 905 10 24 21 20 19 4 1 32 3 13 2 31 28 INK SENSOR PWB Note : Since the parts circled by dots can not .
UX-2200CMU/CMC FO-2150CMU/CMC NO. P ARTS CODE PRICE RANK NEW MARK PA R T RANK DESCRIPTION [8] Printer unit 1 N C Frame chassis 2 N C Carrier cover(K) 3 N C Main shaft 4 N C Main shaft holder 5 N C Bel.
UX-2200CMU/CMC FO-2150CMU/CMC No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher .
デバイスSharp FO-2150CMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sharp FO-2150CMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSharp FO-2150CMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sharp FO-2150CMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sharp FO-2150CMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sharp FO-2150CMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSharp FO-2150CMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sharp FO-2150CMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSharp FO-2150CMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。