ShindaiwaメーカーX7502825300の使用説明書/サービス説明書
ページ先へ移動 of 28
C282 BR USHCUTTER SHIND AIWA O WNER’S/OPERA T OR’S MANU AL Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents.
2 The Shindaiwa 282 series is designed and built to deliver superior per for mance and reliability without compromise to quality , comfor t, safety or durability . Shindaiwa engines represent the leading edge of high-per for mance engine technology , delivering exceptionally high power with remarkably low displacement and weight.
3 W or k Saf el y T rimmers and br ushcutters operate at ver y high speeds and can do serious damage or injur y if they ar e misused or abused. Never allow a person with- out training or instruction to operate this unit! Stay Aler t Y ou must be physically and mentally fit to operate this unit safely .
4 Be Aware of the Working Environment Avoid long-term operation in very hot or very cold weather . Make sure bystanders or observers outside the 15 meter (50 feet) “danger zone” wear eye protection. Be extremely careful of slippery terrain, especially during rainy weather .
5 Product Description Specications Model Name C282 Engine Type 2-cycle catalyst Displacement 28.9 cc / 1.8 cu. in. Bore and Stroke 30 x 35 mm / 1.2 x 1.4 in Dr y W eight (less attachment) 7.0 kg / 15.5 lb. Dimensions (L x H x W) mm 1783 x 345 x 314 mm / 70.
6 Outer T ube Lower Cap Retaining Screws Handlebar Strap Lower cap Hanger Mounting the brushcutter handlebar Handle Positioning Label Assembly Prior to Assembly Before assembling, make sure you have all the components required for a com- plete unit and inspect unit and compo- nents for any damage.
7 4-6 mm Adjust throttle lev er fr ee play The thro ttle lever free play shou ld be approximately 4-6 mm. Make sure that the throttle lever operates smoothly without binding. If it becomes necessar y to adjust the lever free play , follow the procedures and illustrations that follow .
8 Assembly (continued) NOTE: This unit is shipped with Holder A, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT - HAND thread.
9 Assembly (continued) Hex Wrench Tighten the assembly (blade not shown for clarity) CA UTION! Install the blade so its printed sur- face is visible to the operator when the brushcutter is in the normal operating position. The unit should now be completely assembled and ready for use with a blade.
10 Handling Fuel DANGER Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container . • DO NOT smoke near fuel. • DO NOT allow ames or sparks near fuel. • Fuel tanks/cans may be under pressure.
11 Star ting the Engine IMPORT ANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or STAR T and “O” for OFF or STOP . WARNING! Never start the engine from the operating position. Slide the ignition switch to the “I” 1.
12 NEVER operate the unit with the cut - ting attachment shield or other protec - tive devices removed! Use only authorized Shindaiwa par ts and accessories with your Shindaiwa trimmer . Do not make modifications to this unit without written approval from Shindaiwa, Inc.
13 Y our Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for spe - cific applications and/or operational requirements. Cutting gr ass with a trimmer head NOTE: For proper operation, always refer to the instructions accompanying the trim- mer head being used.
14 D O N O T C U T Blade T hr ust “Blade thr ust” is a sudden sideways or backward motion of the br ushcutter . Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CON- STANTL Y ALER T FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS! The blade rotates counter-clockwise.
15 Mufer This unit must never be operated with a faulty or missing spark ar r ester or muf fler . Make sure the muf fler is well secured and in good condition. A wor n or damaged muf fler is a fire hazar d and may also cause hearing loss. Spar k Plug Keep the spark plug and wire connec- tions tight and clean.
16 Air Filter Element Unscrew Fastener Remove and clean or replace the element 10-hour maintenance CA UTION! Do not operate the unit if the air cleaner or lter is damaged, or if the lter is wet or water soaked. Per for m more frequently in dusty or dir ty conditions.
17 Maintenance (continued) Fuel lter element Hooked wire Fuel lter maintenance Remove and replace the fuel filter element. Before reinstalling the new filter element, inspect the condition of all the fuel sys - tem components (fuel pick-up line, fuel retur n line, tank vent line, tank vent, fuel cap and fuel tank).
18 Maintenance (continued) WARNING! Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way . WARNING! Wear protective gloves when handling or performing maintenance on the blade. When the cutting edges of the blade become dull, they can be resharpened with a few strokes of a file.
19 IMPORT ANT! Stored fuel ages. Do not mix more fuel than you expect to use in thir ty (30) days, ninety (90) days when a fuel stabilizer is added. Idle adjustment screw Adjusting engine idle Adjusting Engine Idle The engine must retur n to idle speed whenever the throttle lever is released.
20 T roubleshooting Guide V aporlock. Engine hot/heat soaked. Low fuel quality . Let cool completely and restar t. Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO FD classifi ed oils at 50:1 gasoline/oil ratio.
21 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose terminal.
22 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose terminal.
23 SHINDAIW A LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC’S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited W arranty , provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship.
24 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
25 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance.
26 NO TES.
27 NO TES.
ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-.
デバイスShindaiwa X7502825300の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Shindaiwa X7502825300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはShindaiwa X7502825300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Shindaiwa X7502825300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Shindaiwa X7502825300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Shindaiwa X7502825300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はShindaiwa X7502825300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Shindaiwa X7502825300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちShindaiwa X7502825300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。