SiemensメーカーS7-400の使用説明書/サービス説明書
ページ先へ移動 of 638
Preface, Contents General T echnical Specifications 1 Racks 2 Power Supply Modules 3 Digital Modules 4 Analog Modules 5 Interface Modules 6 IM 463-2 7 PROFIBUS DP Master Interface IM 467/IM 467 FO 8 C.
! Danger indicates that death, severe personal injury or substantial property damage will result if proper precau- tions are not taken. ! W arning indicates that death, severe personal injury or substantial property damage can result if proper precautions are not taken.
iii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Preface Purpose of the Manual The manual contains reference information on operator actions, descriptions of functions and technical specifications of the central processing units, power supply modules and interface modules of the S7-400.
Preface iv S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Changes Compared to the Previous V ersion Since the previous version of the “Module Specifications” referenc.
Preface v S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 System Documentation Package S7-400/M7-400 • S7-400, M7-400 Programmable Controllers; Hardware and Installation.
Preface vi S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Specific Information for S7-400 Y ou require the following manuals and manual packages in order to program and c.
Preface vii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Specific Information for M7-400 This documentation package describes the hardware of the M7-400. Y ou will need the following additional documentation for programming and starting up an M7-400: Documentation Contents Order No.
Preface viii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A&D T echnical Support Worldwide, available 24 hours a day: Johnson City Nuernberg Beijing T echnical Supp.
Preface ix S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Service & Support on the Internet In addition to our documentation, we offer our Know-how online on the internet at: http://www.
Preface x S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
xi S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Contents 1 General T echnical Specifications 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Standards and Approvals 1-2 . . . . .
Contents xii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.12 Power Supply Module PS 405 4A; (6ES7405-0DA01-0AA0) 3-32 . . . . . . . . . . . 3.13 Power Supply Module PS 405 10A; (6ES7405-0KA00-0AA0) 3-34 . . . . . . . .
Contents xiii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.17 Digital Output Module SM 422; DO 16 24 VDC/2 A; (6ES7422-1BH1 1-0AA0) 4-62 . . . . . . . . . . . . . . . . . . . . . 4.18 Digital Output Module SM 422; DO 16 0-125 VDC/1.
Contents xiv S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.13 Connecting Loads/Actuators to Analog Outputs 5-58 . . . . . . . . . . . . . . . . . . . . . . 5.14 Connecting Loads/Actuators to V oltage Outputs 5-59 . . .
Contents xv S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6 Interface Modules 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 Common Features of the Interface Modules 6-2 .
Contents xvi S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 10 RS 485 Repeater 10-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Application and Characteristics (6ES7972-0AA01-0XA0) 10-2 .
Contents xvii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13 Interface Submodules 13-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 Interface Submodules Overview 13-2 .
Contents xviii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.9 IF 964-DP Interface Submodule for S7-400 and M7-400 13-61 . . . . . . . . . . . . . . 13.9.1 Pin Assignments 13-63 . . . . . . . . . . . . . . . . . . . .
Contents xix S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Figures 1-1 Power supply to the backup battery 1-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Structure of a Rack with 18 Slots 2-2 . .
Contents xx S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4-19 T erminal Assignment and Block Diagram of the SM 422; DO 8 x 120/230 V AC/5 A 4-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents xxi S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5-38 Block Diagram of the SM 431; AI 8 x RTD x 16 Bit 5-123 . . . . . . . . . . . . . . . . . . . . 5-39 T erminal Assignment Diagram of the SM 431; AI 8 x RTD x 16 Bit 5-124 .
Contents xxii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1-6 POST Window for a CPU 488-3 1 1-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-7 Warm Restart Window for a CPU 1 1-18 . . .
Contents xxiii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13-20 Connecting Loads/Actuators via a T wo-Wire Connection to a Current Output 13-42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents xxiv S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T ables 1-1 Use in an Industrial Environment 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Products that Fulfill the Requirements of the Low-V oltage Directive 1-3 .
Contents xxv S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4-17 Parameters of the SM 422; DO 16 20-125 VDC/1.5 A 4-69 . . . . . . . . . . . . . . 4-18 Parameters of the SM 422; DO 32 24 VDC/0.5 A (6ES7422-7BL00-0AB0) 4-77 .
Contents xxvi S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5-37 Analog V alue Representation in Output Ranges 0 and 20 mA and 4 to 20 mA 5-27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents xxvii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5-74 Parameters of the SM 431; AI 8 x 16 Bit 5-135 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75 How Response T imes Depend on the Parameterized Interference Frequency Suppression and Smoothing of the SM 431; AI 8 x 16 Bit 5-136 .
Contents xxviii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13-8 Socket X1, X2 IF 962-COM (9-Pin Sub D Plug Connector) 13-1 1 . . . . . . . . . . . . 13-9 Addressing the COM Ports in the A T -Compatible Address Area 13-12 .
1-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 General T echnical Specifications What are General T echnical Specifications? General technical specifications include .
General T echnical Specifications 1-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.1 Standards and Approvals Note Y ou will find the current approvals on the identification label of the respective products.
General T echnical Specifications 1-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Low V oltage Directive The products listed in the table below fulfill the requirements of EU low-voltage directive (73/23/EEC). Adherence to this EU directive was tested in accordance with IEC 61 131-2.
General T echnical Specifications 1-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Mark for Australia and New Zealand Our products satisfy the requirements of Standard AS/NZS 2064 (Class A). Note Y ou will recognize the approval assigned to your product from the mark on the identification label.
General T echnical Specifications 1-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 or cULus Approval, Hazardous Location CULUS Listed 7RA9 INT . CONT . EQ. FOR HAZ. LOC. Underwriters Laboratories Inc. nach UL 508 (Industrial Control Equipment) CSA C22.
General T echnical Specifications 1-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 cuULu requirements on hazardous location on the battery power supply for CPUs The power supply to the backup battery of a CPU must be via a non–incendive plug.
General T echnical Specifications 1-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Battery/Power supply CPU iput “Ext. Batt.” incl. cable Ca ≥ Ci + Cc (25nF + Cc) La ≥ Li + Lc (2mH + Lc) The batteries used must have the following properties: • Battery technology: Li/SOCL2 • Model: AA • V oltage: 3.
General T echnical Specifications 1-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 FM Approval Factory Mutual Approval Standard Class Number 361 1, Class I, Division 2, Group A, B, C, D.
General T echnical Specifications 1-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Safety Requirements for Installation The S7-400/M7-400 programmable controllers are .
General T echnical Specifications 1-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Pulse-Shaped Interference The following table shows the electromagnetic compatibility of modules when there are pulse-shaped disturbance variables.
General T echnical Specifications 1-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Emission of Radio Interference Interference emission of electromagnetic fields in accordance with EN 5501 1: Limit value class A, Group 1.
General T echnical Specifications 1-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Additional Measures If you want to connect an S7-400 or M7-400 system to the public power system, you must ensure compliance with limit value class B in accordance with EN 55022 .
General T echnical Specifications 1-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Storing Backup Batteries Backup batteries must be stored in a cool, dry place. The maximum storage time is 10 years. ! W arning Improper handling of backup batteries can cause injury and material damage.
General T echnical Specifications 1-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.4 Mechanical and Ambient Climatic Conditions for Operating the S7-400/M7-400 Operating Conditions The S7-400/M7-400 is designed for weather-protected use as a permanent installation.
General T echnical Specifications 1-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 1-1 1 Ambient Mechanical Conditions for the MSM 478 Mass Storage Module in Operation Frequency Range in Hz Test Values 10 ≤ f < 58 0.
General T echnical Specifications 1-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 1-13 Ambient Climatic Conditions for the S7-400 Climatic Conditions Remark Permitted Range Relative humidity Max.
General T echnical Specifications 1-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Ambient Climatic Conditions for the M7-400 The M7-400 may be used under the followin.
General T echnical Specifications 1-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.5 Information on Insulation T ests, Protection Class and Degree of Protection T es.
General T echnical Specifications 1-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.6 Using S7-400 in a zone 2 explosion–risk area Y ou will find important information in different languages in the chapters below . Chapter overview Chapter Thema 1.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-20 A5E00069467-07 1.6.1 Einsatz der S7-400 im explo sionsgefährdeten Bereich Zone 2 Zone 2 Explos ionsgef ährdet e Berei che werden in Z onen eingetei lt.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-21 Instandhaltung Für eine Re parat ur m uss die betroff ene Bau grupp e an den Fert igungsor t gesc hick t werden. Nur d ort d arf die R eparat ur durchg eführ t werden.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-22 A5E00069467-07 1.6.2 Use of the S7-400 in a Zone 2 Hazardous A rea Zone 2 Hazardous areas are divi ded up into zon es. The zones are distin guis hed accor ding to the prob abil it y of the exis tence of an ex plosi ve atm osphere.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-23 Main tenance If repair is nec essar y, the a ffec ted m odule m ust be sent to t he produc tio n locati on. Repairs can onl y be carr ied out t here.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-24 A5E00069467-07 1.6.3 Utilisation du S7-400 dans un env ironnement à risque d'explosion en zone 2 Zone 2 Les envir onn em ents à risque d'ex plos ion so nt répar tis en zones .
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-25 Entretien Si une r éparat ion est néces sair e, le m odule co ncerné doit êtr e ex pédié au lieu d e production. La ré paratio n ne do it êtr e eff ectuée q u'en ce li eu.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-26 A5E00069467-07 1.6.4 A plicación de la S7-400 en áre as con peligro de exp losión, zona 2 Zona 2 Las áreas c on pe ligro d e ex plosió n se cl asif ican en zonas .
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-27 Mantenimiento Para una re parac ión se ha de rem itir el m ódulo afec tado a l lugar de fabric ac ión. Sólo allí se p uede re alizar la repar ac ión.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-28 A5E00069467-07 1.6.5 Impiego dell'S7- 400 nell'area a per icolo di esplosion e zona 2 Zona 2 Le aree a pericolo di es plosion e vengono suddivis e in zone.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-29 Manutenzione Per una r ipara zione, l'u nità interess ata d eve es sere inviata al lu ogo di produ zione. La ripara zione può es sere eff ettuata solo lì .
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-30 A5E00069467-07 1.6.6 Gebruik van de S7-4 00 in het explosief gebied zone 2 Zone 2 Explos ieve geb ieden word en inged eeld in zo nes.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-31 Instandhouding Voor een re parat ie m oet de betreff ende m odule na ar d e plaats van v ervaardi ging worden ges tuurd. Allee n daar m ag de reparat ie worde n uitge voerd.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-32 A5E00069467-07 1.6.7 Brug af S7-400 i d et eksplosionfar lige område zone 2 Zone 2 Eks plosionsf arlig e om råder ind deles i zoner . Zo nerne adsk iller s ig in db yrdes efter hvor sands ynligt det er, at der er e n ek splosiv atm os fære.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-33 Vedligeholdelse Skal den pågæld ende k ompone nt repar eres, b edes D e sende de n til produk tionssted et. Repar ation m å k un udføres der.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-34 A5E00069467-07 1.6.8 S7-400:n kä y ttö räjähdy svaarannetuilla alu eilla, vy öhyke 2 Vyöhyke 2 Räjähd ysvaaran netut a luee t jaetaa n vyöh ykk eisiin.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-35 Kunnossapito Korjausta vart en tä ytyy k ysein en rak enner yhm ä lähett ää valm istus paik kaan. Korjaus v oidaan s uorittaa aino astaan s iellä.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-36 A5E00069467-07 1.6.9 A n vändning av S7-400 i explosionsris kområde zon 2 Zon 2 Explos ionsrisk om råden de las in i zon er. Zon erna dela s in enl igt sa nnolik heten att en atmos fär med explos ion sf ara för eligger.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-37 Underhåll Vid repar ation m ås te den a ktuella k om ponentgr uppen ins ändas till ti llverk aren. Reparatio ner får endas t genomf öras där.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-38 A5E00069467-07 1.6.10 Uso do S7-400 em ár ea exposta ao perigo de explosão 2 Zona 2 As áreas ex pos tas ao per ig o de expl osão são div ididas em zonas.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-39 Reparo Os com ponente em ques tão de ve ser rem etid o par a o local de prod ução a fim de que seja re ali zado o re paro. Ap enas lá de ve ser ef etuado o r eparo.
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-40 A5E00069467-07 1.6.11 Χρήση της συσκευής S7-400 σε επικίνδυν η γ.
General Tec hnical Specif icatio ns S7-400, M7-400 Programm able Controllers Module Specific ations A5E00069467-07 1-41 Συντήρηση Για µ ια επισκε υή πρέ πει να στ αλθεί το αντίσ τοι χο δο µ ικό συ γκρότη µ α στον τόπο κατασκευ ής .
General Tec hnical Specif icatio ns S 7-400, M7-400 Programmable Control lers Module Specificat ions 1-42 A5E00069467-07.
Racks 2-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Racks Chapter Overview Section Description Page 2.1 Function and Structure of the Racks 2-2 2.2 The Racks UR1; (6ES7400-1TA01-0AA0) and UR2; (6ES7400-1JA01-0AA0) 2-3 2.
Racks 2-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.1 Function and Structure of the Racks Introduction The racks in the S7-400 have the following tasks: • They h.
Racks 2-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.2 The Racks UR1; (6ES7400-1TA01-0AA0) and UR2; (6ES7400-1JA01-0AA0) Introduction The UR1 and UR2 racks are used for assembling central racks and expansion racks. The UR1 and UR2 racks have both an I/O bus and a communication bus.
Racks 2-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the UR1 and UR2 Racks Rack UR1 UR2 Number of single-width slots 18 9 Dimensions W x H x D (in mm) 482.5 x 290 x 27.5 257.5 x 290 x 27.5 Weight (in kg) 3 4.
Racks 2-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.3 The Rack UR2-H; (6ES7400-2JA00-0AA0) Introduction The UR2-H rack is used for assembling two central racks or expansion racks in one rack. The UR2-H rack essentially represents two electrically isolated UR2 racks on the same rack profile.
Racks 2-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 ! Caution Danger of damage to equipment. If you insert a power supply module in a slot that is not permitted for power supply modules, the module may be damaged.
Racks 2-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.4 The Rack CR2; (6ES7401-2TA01-0AA0) Introduction The CR2 rack is used for assembling segmented central racks. The CR2 has both an I/O bus and a communication bus.
Racks 2-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.5 The Rack CR3; (6ES7401-2T A01-0AA0) Introduction The CR3 rack is used for the assembly of CRs in standard systems (not in fault-tolerant systems). The CR3 has an I/O bus and a communication bus.
Racks 2-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.6 The Racks ER1; (6ES7403-1TA01-0AA0) and ER2; (6ES7403-1JA01-0AA0) Introduction The ER1 and ER2 racks are used for assembling expansion racks.
Racks 2-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Structure of ER1 and ER2 465 mm 240 mm 482.5 mm 257.5 mm 290 mm 190 mm 40 mm 1 2 3 4 5 6 7 8 9 1 01 11 2 1 31 4 .
3-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Power Supply Modules Chapter Overview Section Description Page 3.1 Common Characteristics of the Power Supply Modules 3-2 3.2 Redundant Power Supply Modules 3-4 3.3 Backup Battery (Option) 3-6 3.
Power Supply Modules 3-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.1 Common Characteristics of the Power Supply Modules T asks of the Power Supply Modules The power supply modules of the S7-400 supply the other modules in the rack with their operating voltages via the backplane bus.
Power Supply Modules 3-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Switching the Line V oltage Off/On The power supply modules have a making-current limiter in accordance with NAMUR. Power Supply Module in Invalid Slot If you insert the power supply module of a rack in an invalid slot, it will not power up.
Power Supply Modules 3-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.2 Redundant Power Supply Modules Order Numbers and Function T able 3-2 Redundant power supply mo.
Power Supply Modules 3-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Characteristics The redundant power supply of an S7-400 has the following characteristics: • The power supply module delivers a making current in accordance with NAMUR.
Power Supply Modules 3-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.3 Backup Battery (Option) Introduction The power supply modules of the S7-400 have a battery compartment for one or two backup batteries. Use of these batteries is optional.
Power Supply Modules 3-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Backup Times The maximum backup time is based on the capacity of the backup batteries used and the backup current in the rack.
Power Supply Modules 3-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.4 Controls and Indicators Introduction The power supply modules of the S7-400 have essentially the same controls and indicators.The main differences are: • Not all the power supply modules have a voltage selector .
Power Supply Modules 3-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Meaning of the LEDs The meaning of the LEDs on the power supply modules is described in the tables below . Section 3.5 contains a list of the faults indicated by these LEDs and notes on how to acknowledge the faults.
Power Supply Modules 3-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Battery V oltage on the Backplane Bus The battery voltage is either supplied by the backup battery or externally into the CPU or receive IM. In its normal state, the level of the battery voltage is between 2.
Power Supply Modules 3-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function of the Operator Controls T able 3-6 Function of the operator controls of the power supp.
Power Supply Modules 3-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Cover The battery compartment, battery selector switch, voltage selector switch and power connection are housed under one cover .
Power Supply Modules 3-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.5 Fault/Error Messages via LEDs Introduction The power supply modules of the S7-400 indicate module faults and backup battery faults via LEDs on the front plate.
Power Supply Modules 3-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 3-8 INTF , DC5V , DC24V LEDs, continued LED INTF Remedy Cause of Fault DC24V DC5V H D* D Short circuit or overload on 5 V and 24 V Check load on the power supply module.
Power Supply Modules 3-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 The following power supply modules will switch off in the event of a short circuit or overload after 1 s to 3 s. The module will try to restart after no more than 3 s.
Power Supply Modules 3-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 BAF , BA TTF The following table applies to power supply modules with one battery if the BA TT INDIC switch is in the BA TT position. It shows the faults indicated and lists how to remedy the faults.
Power Supply Modules 3-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 BAF , BA TT1F , BA TT2F The following table applies to power supply modules with two batteries if the BA TT INDIC switch is in the 1BA TT position. It shows the faults indicated and lists how to remedy the faults.
Power Supply Modules 3-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 The following table applies to power supply modules with two batteries if the BA TT INDIC switch is in the 2BA TT position. It shows the faults indicated and lists how to remedy the faults.
Power Supply Modules 3-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.6 Power Supply Module PS 407 4A; (6ES7407-0DA00-0AA0) Function The PS 407 4 A power supply module is designed for connecting to an AC line voltage of 120/230 V AC and supplies 5 VDC/4 A and 24 VDC/0.
Power Supply Modules 3-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 407 4A Programming Package Associated programming package As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 25x290x217 0.
Power Supply Modules 3-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.7 Power Supply Module PS 407 4A; (6ES7407-0DA01-0AA0) Function The PS 407 4A power supply module is designed for connecting to either an AC line voltage of 85 to 264 V or a DC line voltage of 88 to 300 V and supplies 5 VDC/4 A and 24 VDC/0.
Power Supply Modules 3-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Polarity Reversal of L+ and L- The polarity reversal of L+ and L- with supply voltages of between 88 VDC and 300 VDC has no effect on the function of the power supply .
Power Supply Modules 3-23 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.8 Power Supply Modules PS 407 10A; (6ES7407-0KA01-0AA0) and PS 407 10A R; (6ES7407-0KR00-0AA0) Function The power supply modules PS 407 10A (standard) and PS 407 10A R (redundancy-capable, see Section 3.
Power Supply Modules 3-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Power Connection In contrast to the instructions on installing a power supply module described in.
Power Supply Modules 3-25 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 407 10A and the PS 407 10A R Dimensions, W eight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight Cable cross-section 50x290x217 1.
Power Supply Modules 3-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.9 Power Supply Module PS 407 20A; (6ES7407-0RA00-0AA0) Function The PS 407 20 A power supply module is designed for connecting to an AC line voltage of 120/230 V AC and supplies 5 VDC/20 A and 24 VDC/1 A on the secondary side.
Power Supply Modules 3-27 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 407 20 A Programming Package Associated programming package As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight Cable cross-section 75x290x217 1.
Power Supply Modules 3-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.10 Power Supply Module PS 407 20A ; (6ES7407-0RA01-0AA0) Function The PS 407 20 A power supply .
Power Supply Modules 3-29 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Polarity Reversal of L+ and L- The polarity reversal of L+ and L- with supply voltages of between 88 VDC and 300 VDC has no effect on the function of the power supply .
Power Supply Modules 3-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.1 1 Power Supply Module PS 405 4A; (6ES7405-0DA00-0AA0) Function The PS 405 4 A power supply module is designed for connecting to a DC line voltage of 24 VDC and supplies 5 VDC/4 A and 24 VDC/0.
Power Supply Modules 3-31 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 405 4 A Programming Package Associated programming package As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 25x290x217 0.
Power Supply Modules 3-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.12 Power Supply Module PS 405 4A; (6ES7405-0DA01-0AA0) Function The PS 405 4A power supply module is designed for connection to a DC line voltage of 19.
Power Supply Modules 3-33 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 405 4 A Dimensions, W eight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 25x290x217 0.76 kg g Cable cross-section g 3 x 1.
Power Supply Modules 3-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.13 Power Supply Module PS 405 10A; (6ES7405-0KA00-0AA0) Function The PS 405 10A power supply module is designed for connection to a DC line voltage of 24 VDC and supplies 5 VDC/10 A and 24 VDC/1 A on the secondary side.
Power Supply Modules 3-35 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 405 10 A Programming Package Associated programming package As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 50x290x217 1 4 kg W e i g h t Cable cross-section 1 .
Power Supply Modules 3-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.14 Power Supply Modules PS 405 10A; (6ES7405-0KA01-0AA0) and PS 405 10A R; (405-0KR00-0AA0) Function The power supply modules PS 405 10A (standard) and PS 405 10A R (redundancy-capable, see Section 3.
Power Supply Modules 3-37 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 405 10A and the PS 405 10A R Dimensions, W eight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 50x290x217 1 4 kg W e i g h t Cable cross-section 1 .
Power Supply Modules 3-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.15 Power Supply Module PS 405 20A; (6ES7405-0RA00-0AA0) Function The PS 405 20 A power supply module is designed for connecting to a DC line voltage of 24 VDC and supplies 5 VDC/20 A and 24 VDC/1 A on the secondary side.
Power Supply Modules 3-39 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 405 20 A Programming Package Associated programming package As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 75x290x217 2 2 kg W e i g h t Cable cross-section 2 .
Power Supply Modules 3-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.16 Power Supply Module PS 405 20A; (6ES7405-0RA01-0AA0) Function The PS 405 20A power supply module is designed for connection to a DC line voltage of 19.
Power Supply Modules 3-41 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the PS 405 20 A Dimensions, W eight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 75x290x217 2 2 kg W e i g h t Cable cross-section 2 .
Power Supply Modules 3-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
4-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Digital Modules Structure of the Chapter The present chapter is subdivided into the following subjects: 1. Overview containing the modules that are available here and a description 2.
Digital Modules 4-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Chapter Overview Section Description Page 4.1 Module Overview 4-3 4.2 Sequence of Steps from Choosing to Commissioning the Digital Module 4-5 4.3 Digital Module Parameter Assignment 4-6 4.
Digital Modules 4-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.1 Module Overview Introduction The following tables summarize the most important characteristics of the digital modules. This overview is intended to make it easy to choose the suitable module for your task.
Digital Modules 4-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 4-2 Digital Output Modules: Characteristics at a Glance Module Characte- ristics SM 422; DO 16 24 VDC/2 A (-1BH1x) SM 422; DO 16 20-125 VDC/1.5 A (-5EH10) SM 422; DO 32 24 VDC/ 0.
Digital Modules 4-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.2 Sequence of Steps from Choosing to Commissioning the Digital Module Introduction The following table contains the tasks that you have to perform one after the other to commission digital modules successfully .
Digital Modules 4-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.3 Digital Module Parameter Assignment Introduction Digital modules can have different characteristics. Y ou can set the characteristics of dome modules by means of parameter assignment.
Digital Modules 4-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.3.1 Parameters of the Digital Input Modules The parameterized digital input modules use a subset of the parameters and ranges of values listed in the table below , depending on functionality .
Digital Modules 4-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.3.2 Parameters of the Digital Output Modules The parameterized digital output modules use a subset of the parameters and ranges of values listed in the table below , depending on the functionality .
Digital Modules 4-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.4 Diagnostics of the Digital Modules Programmable and Non-Programmable Diagnostic Messages In diagnostics, we make a distinction between programmable and non-programmable diagnostic messages.
Digital Modules 4-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Diagnostic Messages of the Digital Modules The table below gives an overview of the diagnostic messages for the digital modules with diagnostics capability .
Digital Modules 4-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Causes of Errors and Remedial Measures for Digital Modules T able 4-9 Diagnostic Messages of the Digi.
Digital Modules 4-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 4-9 Diagnostic Messages of the Digital Modules, Causes of Errors and Remedial Measures, continu.
Digital Modules 4-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.5 Interrupts of the Digital Modules Introduction This section describes the interrupt behavior of the digital modules.
Digital Modules 4-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Hardware Interrupt A digital input module can trigger a hardware interrupt for each channel at a rising or falling edge, or both, of a signal status change.
Digital Modules 4-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.6 Input Characteristic Curve for Digital Inputs IEC 61 131, T ype 1 and T ype 2 The IEC 61 131 stand.
Digital Modules 4-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Input Characteristic Curve for Digital Inputs As long as the current flowing into the module remains v 1.5 mA, the module recognizes this as a “0” signal.
Digital Modules 4-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.7 Digital Input Module SM 421; DI 32 24 VDC (6ES7421-1BL00-0AA0) Characteristics The SM 421;DI 32 x 24 VDC is a digital input module with the following features: • 32 inputs, isolated in a group of 32.
Digital Modules 4-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the Digital Input Module SM 421; DI 32 x 24 VDC 1 2 3 4 5 6 .
Digital Modules 4-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 32 x 24 VDC Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.8 Digital Input Module SM 421; DI 32 24 VDC; (6ES7421-1BL01-0AA0) Characteristics The digital input .
Digital Modules 4-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 32 24 VDC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15.
Digital Modules 4-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 32 x 24 VDC Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 500 g Data for Specific Module Number of inputs 32 Length of cable • Unshielded • Shielded Max.
Digital Modules 4-23 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.9 Digital Input Module SM 421; DI 16 24 VDC; (6ES7421-7BH00-0AB0) Characteristics The digital input .
Digital Modules 4-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 16 24 VDC INT F EXTF 1L+ 0 1 2 3 1Vs 4 5 6 7 .
Digital Modules 4-25 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram for Redundant Supply of Sensors The figure below shows how sensors can additionally be supplied by means of Vs with a redundant voltage source – for example, via another module).
Digital Modules 4-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Status display Green LED per channel Interrupts • Hardware interrupt.
Digital Modules 4-27 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.9.1 Assigning Parameters to the SM 421; DI 16 24 VDC Parameter Assignment Y ou will find a description of the general procedure for assigning parameters to digital modules in Section 5.
Digital Modules 4-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Ensuring a Wire Break Check Is Carried Out T o ensure that a wire break check is carried out, you requ.
Digital Modules 4-29 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.9.2 Behavior of the SM 421; DI 16 24 VDC Effect of Operating Mode and Supply V oltage on the Input V alues The input values of the SM 421; DI 16 24 DC depend on the operating mode of the CPU and on the supply voltage of the module.
Digital Modules 4-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Effect of Errors and Parameter Assignment on the Input V alues The input values of the SM 421; DI 16 24 DC are affected by certain errors and the parameter assignment of the module.
Digital Modules 4-31 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Behavior when the Input Delay Equals 0.1 ms and an Error Occurs If you have parameterized the following: • An input delay of 0.
Digital Modules 4-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.10 Digital Input Module SM 421; DI 16 24 VDC; (6ES7421-7BH01-0AB0) Characteristics The digital input.
Digital Modules 4-33 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 16 24 VDC INT F EXTF 1L+ 0 1 2 3 1Vs 4 5 6 7 .
Digital Modules 4-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram for Redundant Supply of Sensors The figure below shows how sensors can additionally be supplied by means of Vs with a redundant voltage source – for example, via another module).
Digital Modules 4-35 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Status display Green LED per channel Interrupts • Hardware interrupt.
Digital Modules 4-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.10.1 Assigning Parameters to the SM 421; DI 16 24 VDC Parameter Assignment Y ou will find a description of the general procedure for assigning parameters to digital modules in Section 5.
Digital Modules 4-37 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Ensuring a Wire Break Check Is Carried Out T o ensure that a wire break check is carried out, you requ.
Digital Modules 4-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.10.2 Behavior of the SM 421; DI 16 24 VDC Effect of Operating Mode and Supply V oltage on the Input V alues The input values of the SM 421; DI 16 24 DC depend on the operating mode of the CPU and on the supply voltage of the module.
Digital Modules 4-39 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Effect of Errors and Parameter Assignment on the Input V alues The input values of the SM 421; DI 16 24 DC are affected by certain errors and the parameter assignment of the module.
Digital Modules 4-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Behavior when the Input Delay Equals 0.1 ms and an Error Occurs If you have parameterized the following: • An input delay of 0.
Digital Modules 4-41 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.1 1 Digital Input Module SM 421; DI 16 120 V AC ; (6ES7421-5EH00-0AA0) Characteristics The SM 421; D.
Digital Modules 4-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 421; DI 16 120 V AC 1 2 3 4 0 Byte 0 5 6 1 7 8 2 9 10 3 11 13 1.
Digital Modules 4-43 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 16 120 V AC Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-44 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.12 Digital Input Module SM 421; DI 16 24/60 VUC; (6ES7 421-7DH00-0AB0) Characteristics The SM 421; D.
Digital Modules 4-45 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 16 24/60 VUC L N 1 2 3 4 5 6 7 8 9 10 11 12 1.
Digital Modules 4-46 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 16 24/60 VUC Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-47 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.12.1 Assigning Parameters to the SM 421; DI 16 24/60 VUC Parameter Assignment Y ou will find a description of the general procedure for assigning parameters to digital modules in Section 4.
Digital Modules 4-48 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Setting the Input Delay for Channel Groups Y ou can only set the input delay for each group of channels. In other words, the setting for channel 0 applies to inputs 0 to 7 and the setting for channel 8 applies to inputs 8 to 15.
Digital Modules 4-49 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Circuit as for active high or active low input ”1” ”0” 0V – L+ U_s ”1” U_s DI_x ”1” .
Digital Modules 4-50 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.13 Digital Input Module SM 421; DI 16 120/230 VUC; (6ES7 421-1FH00-0AA0) Characteristics The SM 421;.
Digital Modules 4-51 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 16 120/230 VUC 1 2 3 4 5 6 7 8 9 10 11 12 13 .
Digital Modules 4-52 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 16 120/230 VUC Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-53 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.14 Digital Input Module SM 421; DI 16 120/230 VUC; (6ES7421-1FH20-0AA0) Characteristics The SM 421; .
Digital Modules 4-54 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 16 120/230 VUC 1 2 3 4 5 6 7 8 9 11 12 13 14 .
Digital Modules 4-55 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 16 x 120/230 VUC Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-56 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.15 Digital Input Module SM 421; DI 32 120 VUC ; (6ES7421-1EL00-0AA0) Characteristics The SM 421; DI .
Digital Modules 4-57 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 421; DI 32 120 VUC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1.
Digital Modules 4-58 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 421; DI 32 120 VUC Dimensions and W eight Dimensions W H D (mm) 25 290 210 Weight Approx.
Digital Modules 4-59 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.16 Digital Output Module SM 422; DO 16 24 VDC/2 A; (6ES7422-1BH10-0AA0) Characteristics The digital output module SM 422; DO 16 24 VDC/2 A has the following features.
Digital Modules 4-60 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 422; DO 16 24 VDC/2 A Data register and bus control L.
Digital Modules 4-61 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 16 24 VDC/2 A Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-62 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.17 Digital Output Module SM 422; DO 16 24 VDC/2 A; (6ES7422-1BH1 1-0AA0) Characteristics The digital output module SM 422; DO 16 24 VDC/2 A has the following features.
Digital Modules 4-63 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 422; DO 16 24 VDC/2 A Data register and bus control L.
Digital Modules 4-64 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 16 24 VDC/2 A Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-65 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.18 Digital Output Module SM 422; DO 16 20-125 VDC/1.
Digital Modules 4-66 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 422; DO 16 20-125 VDC/1.
Digital Modules 4-67 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 16 20-125 VDC/1.5 A Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 800 g Data for Specific Module Number of outputs 16 Length of cable • Unshielded • Shielded Max.
Digital Modules 4-68 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Note If the power supply is switched on by means of a mechanical contact, a voltage pulse may occur at the outputs. The transient pulse lasts a maximum of 0.
Digital Modules 4-69 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.18.1 Assigning Parameters to the SM 422; DO 16 20-125 VDC/1.5 A Parameter Assignment Y ou will find a description of the general procedure for assigning parameters to digital modules in Section 5.
Digital Modules 4-70 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.19 Digital Output Module SM 422; DO 32 24 VDC/0.5 A; (6ES7422-1BL00-0AA0) Characteristics The SM 422; DO 32 x 24 VDC/0.5 A has the following features: • 32 outputs, isolated in a group of 32 • Power is supplied to 8 channels in groups.
Digital Modules 4-71 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 422; DO 32 24 VDC/0.
Digital Modules 4-72 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 32 24 VDC/0.5 A Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-73 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.20 Digital Output Module SM 422; DO 32 24 VDC/0.5 A; (6ES7422-7BL00-0AB0) Characteristics The digital output module SM 422; DO 32 24 VDC/0.5 A has the following features: • 32 outputs, fused and isolated in groups of 8 • 0.
Digital Modules 4-74 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 422; DO 32 24 VDC/0.
Digital Modules 4-75 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 32 24 VDC/0.
Digital Modules 4-76 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Time, Frequency Internal preparation time between backplane bus and input of the output driver 1) Up to hardware release 03 • independent of enable diagnostics/diagnostic interrupt/ substitute value max.
Digital Modules 4-77 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.20.1 Assigning Parameters to the SM 422; DO 32 24 VDC/0.5 A Parameter Assignment Y ou will find a description of the general procedure for assigning parameters to digital modules in Section 5.
Digital Modules 4-78 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.20.2 Behavior of the SM 422; DO 32 24 VDC/0.5 A Effect of Operating Mode and Supply V oltage on the Output V alues The output values of the SM 422; DO 32 24 VDC/0.
Digital Modules 4-79 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.21 Digital Output Module SM 422; DO 8 120/230 V AC/5 A; (6ES7422-1FF00-0AA0) Characteristics The SM .
Digital Modules 4-80 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 422; DO 8 120/230 V AC/5 A 1 2 3 4 5 6 7 8 9 10 11 12.
Digital Modules 4-81 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 8 120/230 V AC/5 A Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-82 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Changing Fuses ! W arning This can result in injury . If you change a fuse without removing the front connector of the module, you could be injured by an electric shock.
Digital Modules 4-83 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.22 D igi ta l Out pu t M odule S M 422; DO 16 120/230 V AC/2 A; (6ES7422-1FH00-0AA0) Characteristics.
Digital Modules 4-84 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the SM 422; DO 16 120/230 V AC/2 A Byte 0 16 digital outputs.
Digital Modules 4-85 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 16 120/230 V AC/2 A Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight DimensionsW H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-86 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Changing Fuses ! W arning This can result in injury . If you change a fuse without removing the front connector of the module, you could be injured by an electric shock.
Digital Modules 4-87 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.23 Digital Output Module SM 422; DO 16 20-120 V AC/2 A; (6ES7422-5EH00-0AB0) Characteristics The SM .
Digital Modules 4-88 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 422; DO 16 20-120 V AC/2 A 1 2 3 4 0 Byte 0 5 6 1 7 8 2 9 10 3 .
Digital Modules 4-89 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 422; DO 16 20-120 V AC/2 A Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 800 g Data for Specific Module Number of outputs 16 Length of cable • Unshielded • Shielded Max.
Digital Modules 4-90 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Changing Fuses ! W arning This can result in injury . If you change a fuse without removing the front connector of the module, you could be injured by an electric shock.
Digital Modules 4-91 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.24 R e l a y O u t p u t M odule SM 422; DO 16 30/230 VUC/Rel.
Digital Modules 4-92 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment and Block Diagram of the S M 422; DO 16 30/230 VUC/Rel.
Digital Modules 4-93 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the S M 422; DO 16 30/230 VUC/Rel. 5 A Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Digital Modules 4-94 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Note Use a suppressor circuit in environments with high humidity and where sparks might occur at the relay contacts. This will increase the life of the relay contacts.
5-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog Modules Structure of the Chapter The present chapter is broken down into the following subjects: 1. Overview containing the modules that are available here and a description 2.
Analog Modules 5-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Chapter Overview Section Description Page 5.1 Module Overview 5-3 5.2 Sequence of Steps from Choosing to Commissioning the Analog Modules 5-6 5.3 Analog V alue Representation 5-7 5.
Analog Modules 5-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.1 Module Overview Introduction The following tables summarize the most important characteristics of the analog modules. This overview is intended to make it easy to choose the suitable module for your task.
Analog Modules 5-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-1 Analog Input Modules: Characteristics at a Glance, continued Module SM 431; AI 8 16 Bit (-7KF.
Analog Modules 5-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-2 Analog Output Modules: Characteristics at a Glance Module SM 432; AO 8 13 Bit (-1HF00-) Characteristics Max.
Analog Modules 5-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.2 Sequence of Steps from Choosing to Commissioning the Analog Modules Introduction The following table contains the tasks that you have to perform one after the other to commission analog modules successfully .
Analog Modules 5-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.3 Analog V alue Representation Introduction This section describes the analog values for all the measuring ranges and output ranges which you can use with the analog modules.
Analog Modules 5-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example In the following example you can see how the positions not padded with “0” are written for low resolution.
Analog Modules 5-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-5 Possible Resolutions of the Analog V alues Resolution in Bits Units Analog V alue in Bits Dec.
Analog Modules 5-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Binary Representation of the Input Ranges The input ranges shown in T ables 5-6 to 5-8 are defined in t.
Analog Modules 5-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-8 Life-Zero Input Ranges Units Measured V alue Data Word Range V a l ue in % 2 15 2 14 2 13 2 12 2 11 2 10 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 w 32767 w 1 18.
Analog Modules 5-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-10 Analog V alue Representation in the V oltage Measuring Ranges ± 500 mV to ± 25 mV System V oltage Measuring Range Dec. Hex. ± 500 mV ± 250 mV ± 80 mV ± 50 mV ± 25 mV 1 18.
Analog Modules 5-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation in Current Measuring Ranges T able 5-12 Analog V alue Representation in the Current Measuring Ranges ± 20 mA to ± 3.2 mA System Current Measuring Range Dec.
Analog Modules 5-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-14 Analog V alue Representation in Current Measuring Ranges 4 to 20 mA System Current Measuring Range Dec. Hex. 4 to 20 mA 1 18.515% 32767 7FFF 22.
Analog Modules 5-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Resistance Thermometers Pt x00 Standard T able 5-16 Analog V alue Repr.
Analog Modules 5-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Resistance Thermometers Ni x00 Standard T able 5-18 Analog V alue Repr.
Analog Modules 5-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Resistance Thermometers Cu 10 Standard T able 5-20 Analog V alue Representation for Resistance Thermometers Cu 10 Cu 10 Standard Units Cu 10 Standard Units Cu 10 Standard Units S tan d ar d in 5 C (1 Digit = 0.
Analog Modules 5-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Themocouple T ype B T able 5-22 Analog V alue Representation for Therm.
Analog Modules 5-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Thermocouple T ype J T able 5-24 Analog V alue Representation for Ther.
Analog Modules 5-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Thermocouple T ype L T able 5-26 Analog V alue Representation for Ther.
Analog Modules 5-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Thermocouple T ypes R, S T able 5-28 Analog V alue Representation for .
Analog Modules 5-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation for Thermocouple T ype U T able 5-30 Analog V alue Representation for Ther.
Analog Modules 5-23 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.3.2 Analog V alue Representation for Analog Output Channels Introduction The tables in this chapter contain the analog value representation for output channels of the analog output modules.
Analog Modules 5-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-32 Unipolar Output Ranges Units Output V al e in Data Word Range V alue in % 2 1 5 2 1 4 2 1 3 2 1 2 2 11 2 1 0 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 w 32512 0% 0 1 1 1 1 1 1 1 x x x x x x x x Overflow 3251 1 1 17.
Analog Modules 5-25 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-33 Life-Zero Output Ranges Units Output V al e in % Data Word Range V alue in % 2 1 5 2 1 4 2 1 3 2 1 2 2 11 2 1 0 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 w 32512 0 % 0 1 1 1 1 1 1 1 x x x x x x x x Over- flow 3251 1 1 17.
Analog Modules 5-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation in V oltage Output Ranges T able 5-34 Analog V alue Representation in Output Range ±( 10 V System V oltage Output Range Dec.
Analog Modules 5-27 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog V alue Representation in Current Output Ranges T able 5-36 Analog V alue Representation in Output Range ±( 20 mA System Current Output Range Dec. Hex .
Analog Modules 5-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.4 Setting the Measuring Method and Measuring Ranges of the Analog Input Channels T wo Procedures Ther.
Analog Modules 5-29 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Replugging Measuring Range Modules If you want to replug a measuring range module, perform the following steps: 1. Use a screwdriver to ease the measuring range module out of the analog input module.
Analog Modules 5-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2. Insert the measuring range module (correctly positioned (1)) into the analog input module. The measuring range selected is the one that points to marker point on module (2).
Analog Modules 5-31 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.5 Behavior of the Analog Modules Introduction In this section, you will find information on: • How .
Analog Modules 5-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Behavior on Failure of the Supply V oltage Failure of the load power supply L+ of the diagnostics-capable analog module is indicated in the case of parameterized two-wire transmitters by the EXTF LED on the module.
Analog Modules 5-33 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Effect of Range of V alues on the Analog Output Module The behavior of the analog modules depends on where the output values lie within the value range.
Analog Modules 5-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example of Determination of the Output Error of a Module An analog output module SM 432; AO 8 13 Bit is being used for voltage output. The output range “ " 10 V” is used.
Analog Modules 5-35 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.6 Conversion, Cycle, Setting and Response Time of Analog Modules Conversion Time of Analog Input Chan.
Analog Modules 5-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Basic Execution Time of the Analog Input Channels The basic execution time corresponds to the cycle time for all the enabled channels.
Analog Modules 5-37 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example The following figure shows the number of module cycles for a step response after which the smoothed analog value is approximately 100% applied, as a function of the smoothing that has been set.
Analog Modules 5-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Basic Execution Time of the Analog Output Channels The basic execution time corresponds to the cycle time for all the enabled channels. Tip Y ou should disable any analog channels that are not being used to reduce the scan time in STEP 7 .
Analog Modules 5-39 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.7 Analog Module Parameter Assignment Introduction Analog modules can have different characteristics. Y ou can set the characteristics of the modules by means of parameter assignment.
Analog Modules 5-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.7.1 Parameters of the Analog Input Modules The analog input modules use a subset of the parameters and ranges of values listed in the table below , depending on the functionality .
Analog Modules 5-41 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-42 Parameters of the Analog Input Modules, continued Parameter Scope Parameter T ype Default 2.
Analog Modules 5-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.7.2 Parameters of the Analog Output Modules The analog output modules use a subset of the parameters and ranges of values listed in the table below , depending on the functionality .
Analog Modules 5-43 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.8 Connecting Sensors to Analog Inputs Introduction Y ou can connect different sensors to the analog input modules depending on the measuring method; voltage and current sensors, and resistors.
Analog Modules 5-44 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Abbreviations and Mnemonics Used in the Figures Below The abbreviations and mnemonics used in the figur.
Analog Modules 5-45 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Non-Isolated Sensors The non-isolated sensors are connected with the local ground potential (local ground). When using non-isolated sensors, you must connect M ANA to chassis ground.
Analog Modules 5-46 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.9 Connecting V oltage Sensors Note The necessary connecting cables, which result from the potential connection of the analog input module and the sensors, are not drawn in the figures shown below .
Analog Modules 5-47 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.10 Connecting Current Sensors Note The necessary connecting cables, which result from the potential connection of the analog input module and the sensors, are not drawn in the figures shown below .
Analog Modules 5-48 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connecting T wo-Wire T ransmitters +24 V Sensor , for example, pressure gauge + – L + M+ M - M+ M - M.
Analog Modules 5-49 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connecting Four-Wire T ransmitters M+ M– M+ M– M ANA Sensor , for example, pressure gauge + – Fou.
Analog Modules 5-50 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.1 1 Connecting Resistance Thermometers and Resistors Note The necessary connecting cables, which result from the potential connection of the analog input module and the sensors, are not drawn in the figures shown below .
Analog Modules 5-51 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Four-Conductor Connection of a Resistance Thermometer The voltage generated at the resistance thermometer is measured via the M + and M – terminals.
Analog Modules 5-52 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Three-Conductor Connection of a Resistance Thermometer During three-conductor connection to modules with 4 terminals per resistance thermometer , you must set up a jumper between M– and I C – and SE– and AGND (see Figure 5-15).
Analog Modules 5-53 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.12 Connecting Thermocouples Design of Thermocouples A thermocouple consists of a pair of sensors and the necessary installation and connecting parts.
Analog Modules 5-54 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Compensation of the Reference Junction T emperature There are several options for you to choose from fo.
Analog Modules 5-55 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Theory of Operation of Internal Compensation With internal compensation, you can establish the reference point across the terminals of the analog input modules.
Analog Modules 5-56 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connection of Thermocouples without Compensation or Using the Reference T emperature V alue Connect the thermocouples to the inputs of the module, either directly or by means of compensating lines.
Analog Modules 5-57 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Recommended Compensating Box We recommend you to use a comparison point (with integrated power supply unit) from Siemens as a compensating box. Y ou will find the necessary ordering data in the table below .
Analog Modules 5-58 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connecting Thermocouples and Resistance Thermometers Connect the resistance thermometer to channel 0 of the module.
Analog Modules 5-59 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.13 Connecting Loads/Actuators to Analog Outputs Introduction Y ou can use the analog output modules to supply loads and actuators with current and voltage.
Analog Modules 5-60 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.14 Connecting Loads/Actuators to V oltage Outputs Connecting Loads to a V oltage Output Connecting loads to a voltage output is possible both in a four-conductor and a two-conductor connection.
Analog Modules 5-61 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 +24 V L + Q V S+ S– M ANA 0 V M U ISO Chassis ground R L Figure 5-21 Connecting Loads to a V oltage O.
Analog Modules 5-62 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.15 Connecting Loads/Actuators to Current Outputs Note The necessary connecting cables, which result from the potential connection of the analog output module, are not drawn in the figures shown below .
Analog Modules 5-63 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.16 Diagnostics of the Analog Modules Programmable and Non-Programmable Diagnostic Messages In diagnostics, we make a distinction between programmable and non-programmable diagnostic messages.
Analog Modules 5-64 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Diagnostic Messages of the Analog Input Modules The table below gives an overview of the diagnostic messages for the analog input modules with diagnostics capability .
Analog Modules 5-65 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Note A prerequisite for detecting the errors indicated by programmable diagnostic messages is that you must have assigned parameters to the analog module accordingly in STEP 7 .
Analog Modules 5-66 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-47 Diagnostics Messages of the Analog Input Modules, Causes of Errors and Remedial Measures, c.
Analog Modules 5-67 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.17 Analog Module Interrupts Introduction In this Section, the interrupt behavior of the analog modules is described.
Analog Modules 5-68 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Hardware Interrupt with T rigger “Upper or Lower Limit Exceeded” Define a working range by setting parameters for an upper and lower limit value.
Analog Modules 5-69 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Hardware Interrupt on T rigger “Reached End of Scan Cycle” By parameterizing the hardware interrupt a the end of the scan cycle, you have the option of synchronizing a process with the scan cycle of the analog input module.
Analog Modules 5-70 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.18 Analog Input Module SM 431; AI 8 13 Bit; (6ES7431-1KF00-0AB0) Characteristics The analog input mod.
Analog Modules 5-71 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the SM 431; AI 8 13 Bit A D +5V 0V CH1 CH7 CH0 +5V –5V 0V Suppressor circuit, curren.
Analog Modules 5-72 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 8 13 Bit M ANA V A V A V oltage measurement Current meas.
Analog Modules 5-73 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 8 13 Bit Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-74 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Interrupts None Diagnostic functions None Substitute value can be appli.
Analog Modules 5-75 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.18.2 Measuring Methods and Measuring Ranges of the SM 431; AI 8 13 Bit Measuring Methods Y ou can set.
Analog Modules 5-76 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Measuring Ranges Y ou set the measuring ranges by means of the “Measuring Range” parameter in STEP 7 .
Analog Modules 5-77 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.19 Analog Input Module SM 431; AI 8 14 Bit; (6ES7 431-1KF10-0AB0) Characteristics The analog input mo.
Analog Modules 5-78 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 8 14 Bit Thermocouples V oltage measurement Current meas.
Analog Modules 5-79 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 8 14 Bit Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-80 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Suppression of Interference, Limits of Error Interference voltage suppression for f = nx (f1 " 1%), (f1 = interference frequency) n = 1, 2, .
Analog Modules 5-81 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Basic error (operational limit at 25 ° C, referred to input range) • V oltage input – " 80 mV – " 250 mV – " 500 mV – " 1 V – " 2.
Analog Modules 5-82 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Interrupts None Diagnostic functions None Substitute value can be appli.
Analog Modules 5-83 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.19.1 Commissioning the SM 431; AI 8 14 Bit Y ou set the mode of operation of the SM 431; AI 8 14 Bit by means of measuring range modules on the module and in STEP 7 .
Analog Modules 5-84 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-51 Parameters of the SM 431; AI 8 14 Bit, continued Parameter Scope Parameter T ype Default 1 V alue Range • Interference suppression 60 Hz; 50 Hz 50 Hz Static Channel • Smoothing None Low Average High None Static Channel • Ref.
Analog Modules 5-85 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.19.2 Measuring Methods and Measuring Ranges of the SM 431; AI 8 14 Bit Measuring Methods Y ou can set.
Analog Modules 5-86 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Wiring for Resistance and T emperature Measurement The following conditions apply when measuring the re.
Analog Modules 5-87 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Measuring Ranges Y ou set the measuring ranges by means of the measuring range modules on the module and the “Measuring T ype” parameter in STEP 7 .
Analog Modules 5-88 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-55 Measuring Ranges of the SM 431; AI 8 x 14 Bit, continued Method Selected Description Measur.
Analog Modules 5-89 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Wire Break Check for T emperature or Resistance Measurement The wire break check is intended primarily for temperature measurements (TC, RTD) or resistance measurements.
Analog Modules 5-90 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.20 Analog Input Module SM 431; AI 8 14 Bit; (6ES7431-1KF20-0AB0) Characteristics The analog input mod.
Analog Modules 5-91 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 8 14 Bit V oltage measurement Current measurement Resist.
Analog Modules 5-92 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 8 14 Bit Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-93 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Suppression of interference, Limits of Error Interference voltage suppression parameterized for f = nx (f1 " 1%), (f1 = interference frequency) n = 1, 2 , .
Analog Modules 5-94 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.20.1 Commissioning the SM 431; AI 8 14 Bit Y ou set the mode of operation of the SM 431; AI 8 14 Bit by means of measuring range modules on the module and in STEP 7 .
Analog Modules 5-95 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Smoothing of the Measured V alues Y ou will find information that is generally applicable to the smoothing of analog values in Section 5.6. Y ou can only set strong smoothing for the SM 431; AI 8 14 Bit.
Analog Modules 5-96 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Step Response with Strong Smoothing The following figure illustrates the contents of T able 5-57.
Analog Modules 5-97 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Circuit V ariants of the Channels T wo channels are set in each case with the measuring range module.
Analog Modules 5-98 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Unused Channels Unused channels can usually be left open. Put the measuring range modules in position “B”. Y ou can improve the noise immunity of the module in a measuring environment with serious interference by connecting M– and M ANA .
Analog Modules 5-99 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.21 Analog Input Module SM 431; AI 16 13 Bit; (6ES7431-0HH00-0AB0) Characteristics The analog input mo.
Analog Modules 5-100 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the SM 431; AI 16 x 13 Bit Tr Tr Tr Tr Tr Tr Tr Tr * *V oltage/current sensor and M m.
Analog Modules 5-101 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 16 x 13 Bit V oltage measurement Current measurement M1.
Analog Modules 5-102 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 16 x 13 Bit Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 500 g Data for Specific Module Number of inputs • Shielded 16 Max.
Analog Modules 5-103 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Data for Selecting a Sensor Input range (rated values)/Input resistance • V oltage " 1 V/10 M .
Analog Modules 5-104 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.21.1 Commissioning the SM 431; AI 16 13 Bit Y ou set the mode of operation of the SM 431; AI 16 13 Bit by means of measuring range modules on the module and in STEP 7 .
Analog Modules 5-105 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.21.2 Measuring Methods and Measuring Ranges of the SM 431; AI 16 13 Bit Measuring Methods Y ou can s.
Analog Modules 5-106 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Unused Channels Unused channels can usually be left open. Put the measuring range modules in position “B”. Y ou can improve the noise immunity of the module in a measuring environment with serious interference by connecting M– and chassis ground.
Analog Modules 5-107 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.22 Analog Input Module SM 431; AI 16 16 Bit; (6ES7431-7QH00-0AB0) Characteristics The analog input m.
Analog Modules 5-108 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the SM 431; AI 16 16 Bit Bus S7-400 Bus control A D CH0 CH1 + 15 V + 5 V 0 V –15 V + 5 V 0 V I const Diagnostics in L+ loop L + M PGA Multiplexer Opto relay CH14 CH15 Meas.
Analog Modules 5-109 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 16 16 Bit Thermocouples V oltage measurement Current me.
Analog Modules 5-1 10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 16 16 Bit Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-1 1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Suppression of Interference, Limits of Error Interference voltage suppression for f = nx (f1 " 1%), (f1 = interference frequency) n = 1, 2, .
Analog Modules 5-1 12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Basic error (operational limit at 25 ° C, referred to input range) • V oltage input – " 25 mV – " 50 mV – " 80 mV – " 250 mV – " 500 mV – " 1 V – " 2.
Analog Modules 5-1 13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Interrupts • Hardware interrupt Parameters can be assigned • Hard.
Analog Modules 5-1 14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.22.1 Commissioning the SM 431; AI 16 16 Bit Y ou set the mode of operation of the SM 431; AI 16 16 Bit by means of measuring range modules on the module and in STEP 7 .
Analog Modules 5-1 15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-64 Parameters of the SM 431; AI 16 16 Bit, continued Parameter Scope Parameter T ype Default.
Analog Modules 5-1 16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Smoothing of the Measured V alues Y ou fill find information that is generally applicable to the smoothing of analog values in Section 5.
Analog Modules 5-1 17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.22.2 Measuring Methods and Measuring Ranges of the SM 431; AI 16 16 Bit Measuring Methods Y ou can .
Analog Modules 5-1 18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example If you have select “current (two-wire transmitter)” for channel 6, you can only disable the measuring method or set “current (two-wire transmitter)” for channel 7.
Analog Modules 5-1 19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Unused Channels Unused channels can usually be left open. Put the measuring range modules in position “A”. Y ou can improve the noise immunity of the module in a measuring environment with serious interference by short-circuiting the channels.
Analog Modules 5-120 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-69 Measuring Ranges of the SM 431; AI 16 x 16 Bit, continued Method Selected Description Measuring Range Module Setting Measuring Range (T ype of Sensor) R-3L: Resistor (three-conductor terminal) 300 600 6000 max.
Analog Modules 5-121 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Wire Break Check The wire break check is intended primarily for temperature measurements (TC, RTD) or resistance measurements.
Analog Modules 5-122 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.23 Analog Input Module SM 431; AI 8 RTD 16 Bit; (6ES7 431-7KF10-0AB0) Characteristics The analog inp.
Analog Modules 5-123 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the SM 431; AI 8 RTD 16 Bit Backplane bus interface Bus S7-400 SO+0 SE+0 SE–0 AGND .
Analog Modules 5-124 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 8 RTD 16 Bit SO0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 SE+0 S.
Analog Modules 5-125 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 8 RTD 16 Bit Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-126 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.23.1 Commissioning the SM 431; AI 8 RTD 16 Bit Y ou set the mode of operation of the SM 431; AI 8 RTD 16 Bit in STEP 7 . Parameters Y ou will find a description of the general procedure for assigning parameters to analog modules in Section 5.
Analog Modules 5-127 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-71 Parameters of the SM 431; AI 8 RTD 16 Bit, continued Parameter Scope Parameter T ype Defau.
Analog Modules 5-128 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Displaying Parameter Assignment Errors The SM 431; AI 8 RTD 16 Bit is capable of diagnostics. Below you will find an overview of the displays that are possible for modules with parameter assignment errors.
Analog Modules 5-129 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.23.2 Measuring Methods and Measuring Ranges of the SM 431; AI 8 RTD 16 Bit Measuring Methods As the measuring method for the input channels, you can set the temperature measurement.
Analog Modules 5-130 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.24 Analog Input Module SM 431; AI 8 16 Bit; (6ES7431-7KF00-0AB0) Characteristics The analog input mo.
Analog Modules 5-131 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the SM 431; AI 8 16 Bit Backplane bus interface Bus S7-400 M0+ M0+ R0 M0– CH1 CH2 C.
Analog Modules 5-132 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 431; AI 8 16 Bit R0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 M0+ M0+ M0.
Analog Modules 5-133 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 431; AI 8 16 Bit Dimensions and W eight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-134 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operational limit (in the entire temperature range, with reference to the input range) • V oltage input " 0.3 % • Current input " 0.5 % • Thermocouple T ype B " 3.
Analog Modules 5-135 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.24.1 Commissioning the SM 431; AI 8 16 Bit Y ou set the mode of operation of the SM 431; AI 8 16 Bit in STEP 7 . Parameter Y ou will find a description of the general procedure for assigning parameters to analog modules in Section 5.
Analog Modules 5-136 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 5-74 Parameters of the SM 431; AI 8 16 Bit, continued Parameter Scope Parameter T ype Default 2.
Analog Modules 5-137 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Step Response at an Interference Frequency Suppression of 10 Hz 100 0 Smoo- thing: None: Low: Average:.
Analog Modules 5-138 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Step Response at an Interference Frequency Suppression of 60 Hz 100 0 Smoo- thing: None: Low: Average: High: Response time in ms Signal variation in percent Step response for any analog input signal 160 80 240 320 400 480 560 640 16.
Analog Modules 5-139 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Displaying Parameter Assignment Errors The SM 431; AI 8 16 Bit has diagnostics capability . Below you will find an overview of the displays that are possible for modules with parameter assignment errors.
Analog Modules 5-140 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Measuring Ranges Y ou set the measuring ranges by means of the “Measuring Range” parameter in STEP 7 .
Analog Modules 5-141 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.25 Analog Output Module SM 432; AO 8 13 Bit; (6ES7432-1HF00-0AB0) Characteristics The SM 432; AO 8 x.
Analog Modules 5-142 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Assignment Diagram of the SM 432; AO 8 x 13 Bit V oltage output Current output S0– CH0 CH1.
Analog Modules 5-143 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the SM 432; AO 8 x 13 Bit Programming package Associated programming package As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx.
Analog Modules 5-144 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Repeat accuracy (in the steady state at 25 ° C, referred to the output range) " 0.05% Output ripple; band width 0 to 50 kHz (with reference to the output range) " 0.
Analog Modules 5-145 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.25.1 Commissioning the SM 432; AO 8 13 Bit Parameter Y ou will find a description of the general procedure for assigning parameters to analog modules in Section 5.
Analog Modules 5-146 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
6-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interface Modules Chapter Overview Section Description Page 6.1 Common Features of the Interface Modules 6-2 6.2 The Interface Modules IM 460-0; (6ES7460-0AA00-0AB0, 6ES7460-0AA01-0AB0) and IM 461-0; (6ES7461-0AA00-0AA0, 6ES7461-0AA01-0AA0) 6-7 6.
Interface Modules 6-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6.1 Common Features of the Interface Modules Function Interface modules (a send IM and a receive IM) are required if one or more expansion units (EU) are to be connected to a central controller (CC).
Interface Modules 6-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connection possibilities for central racks and expansion racks Central rack CR Expansion rack ER 1 Ex.
Interface Modules 6-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Rules for Connection When you connect a central rack to expansion racks, you must observe the following rules: • Y ou can connect up to 21 ERs of the S7-400 to one CR.
Interface Modules 6-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 The following figure shows you a typical configuration with send IMs, receive IMs and terminators.
Interface Modules 6-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Installation and Removal of the Modules During Operation Please read the following warning on the insertion and removal of the interface modules and associated connecting cables.
Interface Modules 6-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6.2 The Interface Modules IM 460-0; (6ES7460-0AA00-0AB0, 6ES7460-0AA01-0AB0) and IM 461-0; (6ES7461-0.
Interface Modules 6-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function The interface module pair IM 460-0 (send IM) and IM 461-0 (r ec e iv e IM ) ar e us ed for a local link. The communication bus is transferred at the full transmission rate .
Interface Modules 6-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operator Controls and Indicators of the Receive IM INTF LED (red) Lights up if a rack number > 21 or = 0 was set. Lights up if you have changed the rack number under voltage.
Interface Modules 6-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6.3 The Interface Modules IM 460-1; (6ES7460-1BA00-0AB0, 6ES7460-1BA01-0AB0) and IM 461-1; (6ES7461-.
Interface Modules 6-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function The interface module pair IM 460-1 (send IM) and IM 461-1 (receive IM) are used for a local link (up to a maximum 1.5 m in total). A 5 V supply voltage is also transferred with these interface modules.
Interface Modules 6-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operator Controls and Indicators on the Send IM EXTF LED (red) Lights up in the event of an external fault Line 1 or line 2 is faulty (terminator missing or open circuit) C1 LED (green) Line 1 (via front connector X1, connection 1) is correct.
Interface Modules 6-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the IM 460-1 and IM 461-1 Maximum line length (total) 1.
Interface Modules 6-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6.4 The Interface Modules IM 460-3; (6ES7460-3AA00-0AB0, 6ES7460-3AA01-0AB0) and IM 461-3; (6ES7461-.
Interface Modules 6-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function The interface module pair IM 460-3 (send IM) and IM 461-3 (receive IM) are used for a remote link of up to a maximum 102 m (exactly: 100 m plus inputs/outputs of 0.
Interface Modules 6-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operator Controls and Indicators on the Send IM EXTF LED (red) Lights up in the event of an external fault Line 1 or line 2 is faulty (terminator missing or broken cable) C1 LED (green) Line 1 (via front connector X1, connection 1) is correct.
Interface Modules 6-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the IM 460-3 and IM 461-3 Maximum line length (total) 102 m Dimensions .
Interface Modules 6-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6.5 The Interface Modules IM 460-4; (6ES7460-4AA01-0AB0) and IM 461-4; (6ES7461-4AA01-0AA0) Position.
Interface Modules 6-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function The interface module pair IM 460-4 (send IM) and IM 461-4 (receive IM) are used for a remote link of up to a maximum 605 m (exactly: 600 m plus inputs/outputs of 1.
Interface Modules 6-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operator Controls and Indicators on the Send IM EXTF LED (red) Lights up in the event of an external fault Line 1 or line 2 is faulty (terminator missing or broken cable) C1 LED (green) Line 1 (via front connector X1, connection 1) is correct.
Interface Modules 6-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T echnical Specifications of the IM 460-4 and IM 461-4 Maximum line length (total) 605 m Dimensions .
Interface Modules 6-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
7-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 IM 463-2 Chapter Overview Section Description Page 7.1 Using SIMA TIC S5 Expansion Units in an S7-400 7-2 7.2 Rules for Connecting S5 Expansion Units 7-3 7.3 Operator Controls and Indicators 7-4 7.
IM 463-2 7-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.1 Using SIMA TIC S5 Expansion Units in an S7-400 Area of Application The IM 463-2 interface module is used for distributed connection of S5 expansion units to an S7-400.
IM 463-2 7-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.2 Rules for Connecting S5 Expansion Units Introduction When you connect S5 expansion units to an S7-400 via .
IM 463-2 7-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.3 Operator Controls and Indicators Introduction All controls and indicators on the IM 463-2 are arranged on the front plate. The following figure shows the arrangement of the controls and indicators.
IM 463-2 7-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 LEDs T able 7-2 LEDs of the IM 4632 LED Meaning LED EXTF (red) Lights up in the event of an external fault. Chain 1 or chain 2 has a fault (power supply failed in the EU; terminating connector missing; wire break, or interface selector switch wrongly set).
IM 463-2 7-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.4 Installing and Connecting the IM 463-2 Introduction T o install an IM 463-2 in a CR of the S7-400, proceed in the same way as when installing other S7-400 modules (see Installation Manual , Chapter 5).
IM 463-2 7-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Plugging in the Connecting Cable T o plug in the connecting cable, follow the steps outlined below: 1. Open the cover of the IM 463-2. 2. Plug the new connector of the connecting cable into one of the connectors of the IM 463-2.
IM 463-2 7-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.5 Setting the Operating Modes of the IM 314 Introduction T o operate the IM 463-2, you must set on the IM 314 the S5 expansion unit used and the address area of the S5 I/O modules.
IM 463-2 7-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Setting the Address Area The address area of the S5 I/O modules is set on the IM 314. This setting applies only for the digital and analog I/O modules. The address areas P , Q, IM3, and IM4 are available.
IM 463-2 7-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.6 Configuring S5 Modules for Operation in the S7-400 Y ou configure the S5 modules using STEP 7. See the description of STEP 7 or the online help function for details of how to proceed.
IM 463-2 7-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.7 Pin Assignments of the 721 Connecting Cable T able 7-6 Assignment of the Connecting Cable 721 34 50 17 1 34 50 17 1 Connector 50-Pin Contact Bundle Ident.
IM 463-2 7-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 7-6 Assignment of the Connecting Cable 721, continued Connector 50-Pin Contact Connector 50-Pin Contact Core Color Identification Foil Bundle Ident. Sheath 28 white 28 29 brown 29 12 green 12 13 4 brown yellow 13 46 4 No.
IM 463-2 7-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.8 T erminating Connector for IM 314 Introduction The IM 314 of the last expansion unit of each chain is terminated with the 6ES5 760-1AA1 1 terminating connector .
IM 463-2 7-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.9 T echnical Specifications (6ES7463–2AA00–0AA0) Programming package Associated programming package As of STEP7 V 2.
8-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 PROFIBUS DP Master Interface IM 467/IM 467 FO Chapter Overview Section Description Page 8.1 PROFIBUS DP Master Interface IM 467/IM 467 FO 8-2 8.2 Configuration 8-6 8.3 Connection to PROFIBUS DP 8-8 8.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.1 PROFIBUS DP Master Interface IM 467/IM 467 FO Order Numbers IM 467 6E.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 PROFIBUS DP interface 9-pin subminiature D LEDs Mode selector Figure 8-1 .
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.1.1 Indicators and the Mode Selector LED The LED plate on the front pan.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Controlling the Operating Mode There are two ways to control the operatin.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.2 Configuration The IM 467/IM 467 FO is configured with STEP 7. The configuration data are retained even in the event of a power failure; a memory module is not required.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Prerequisites The IM 467/IM 467 FO is supported by all the CPU operating systems beginning with the release numbers listed below .
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.3 Connection to PROFIBUS DP There are two ways of connecting to PROFIBUS DP: • Electrical connection via a bus connector • Optical connection using a fiber-optic cable 8.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connector Pin Assignment The electrical interface used to connect to PROFIBUS DP (9-pin subminiature D female connector) is specified in the following table.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.3.3 Connecting a Fiber-Optic Cable to the IM 467 FO Accessories Required • Pack of Simplex connectors and polishing sets (6GK1901-0FB00-0AA0) • Pack of plug-in adapters (6ES7195-1BE00-0XA0) Installing Connectors 1.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Reusing Fiber-Optic Cables Note If you insert used fiber-optic cables in the plug-in adapter again, you must cut off the bent lengths of both fiber-optic cable cores and install the Simplex connectors again.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.4 T echnical Specifications 8.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.4.2 T echnical Specifications of the IM 467 FO 6ES7 467-5FJ00-0AB0 Dim.
PROFIBUS DP Master Interface IM 467/IM 467 FO 8-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
9-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Cable Duct and Fan Subassemblies Chapter Overview Section Description Page 9.1 Fan Monitoring in the Fan Subassemblies 9-2 9.2 Cable Duct; (6ES7408-0T A00-0AA0) 9-4 9.3 The 120/230 V AC Fan Subassembly; (6ES7408-1TB00-0XA0) 9-5 9.
Cable Duct and Fan Subassemblies 9-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 9.1 Fan Monitoring in the Fan Subassemblies In this section, you will find out how to monitor the fans. There is a signaling concept example at the end of the section.
Cable Duct and Fan Subassemblies 9-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Signaling Concept Example Y ou can check the fault-free functioning of the fan subassembly using digital inputs. Y ou can cause the power supply to be cut off after the failure of at least two fans by using the relay K2.
Cable Duct and Fan Subassemblies 9-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 9.2 Cable Duct; (6ES7408-0T A00-0AA0) Function The cable duct is used in installations.
Cable Duct and Fan Subassemblies 9-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 9.3 The 120/230 V AC Fan Subassembly; (6ES7408-1TB00-0XA0) Operator Controls and Indic.
Cable Duct and Fan Subassemblies 9-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Shielding Clamps If you do not require the shielding clamps supplied, do not install them in the fan subassembly . T echnical Specifications Dimensions, W eights Dimensions WxHxD (mm) 482.
Cable Duct and Fan Subassemblies 9-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 9.4 The 24 VDC Fan Subassembly; (6ES7408-1T A00-0XA0) Operator Controls and Indicators.
Cable Duct and Fan Subassemblies 9-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Signaling Concept The signaling concept of the 24 VDC fan subassembly is identical to the signaling concept of the 120/230 V AC fan subassembly .
10-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 RS 485 Repeater In this Chapter In this chapter , you will find a detailed description of the RS 485 repeater .
RS 485 Repeater 10-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 10.1 Application and Characteristics (6ES7972-0AA01-0XA0) What is an RS 485 Repeater? The RS 485 repeater amplifies data signals on bus lines and interconnects bus segments.
RS 485 Repeater 10-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 10.2 Appearance of the RS 485 Repeater; (6ES7972-0AA01-0XA0) The table below shows the appearance of the RS 485 repeater and lists its functions. T able 10-3 Description and Functions of the RS 485 Repeater Repeater Design No .
RS 485 Repeater 10-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 10.3 RS 485 Repeater in Ungrounded and Grounded Operation Grounded or Ungrounded The RS 485 repeater is .
RS 485 Repeater 10-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T erminal Connection Diagram In the case of a repeater configuration with ungrounded reference potenti.
RS 485 Repeater 10-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Amplification of the Bus Signals The amplification of the bus signals takes place between the port for bus segment 1 or the PG/OP interface and the port for bus segment 2.
RS 485 Repeater 10-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the RS 485 Repeater • Bus segment 1 and bus segment 2 are galvanically isolated from each other . • Bus segment 2 and the PG/OP socket are galvanically isolated from each other .
RS 485 Repeater 10-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
1 1-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 CPUs for M7-400 In this Chapter This chapter describes the CPUs of the M7-400 automation computer: • CPU 486-3, • CPU 488-3, The CPUs differ essentially in their clock frequencies.
CPUs for M7-400 1 1-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.1 Performance Features Introduction There are two CPUs with different clock frequencies available for use with the automation computer . T able 1 1-1 gives you an overview of the most important performance features of these CPUs.
CPUs for M7-400 1 1-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.2 T echnical Specifications The following table contains the technical specifications of the CPUs for the M7-400 automation computer .
CPUs for M7-400 1 1-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3 Function Elements Introduction In this section you will become familiar with the individual function elements of the CPU 486-3 and CPU 488-3.
CPUs for M7-400 1 1-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 CPU Elements The following table gives the meanings of the individual elements of the CPU 486-3 and CPU 488-3.
CPUs for M7-400 1 1-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.1 Status and Fault LEDs Status and Fault LEDs The CPU 486-3 and CPU 488-3 have the following st.
CPUs for M7-400 1 1-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Meaning of the Status and Fault LEDs The status and fault LEDs are explained in T able 1 1-4 in the order in which they are arranged on the CPU 486-3 and CPU 488-3 modules.
CPUs for M7-400 1 1-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.2 Memory Cards Introduction The CPU 486-3 and CPU 488-3 offer the possibility of operating a memory card in the same way as a diskette. In this section, you will learn how you can use these options.
CPUs for M7-400 1 1-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.3 Mode Selector Switch Mode Selector Switch The mode selector switch of the CPUs is a keyswitch. Y ou can see the positions of the mode selector switch in the following figure.
CPUs for M7-400 1 1-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 1 1-5 Positions of the Mode Selector Switch Position of the Mode Selector Switch Explanations STOP I/O access is disabled for the user program of the CPU.
CPUs for M7-400 1 1-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.4 Submodule Receptacles for Interface Submodules Submodule Receptacle Definition The submodule receptacle is a slot for a submodule.
CPUs for M7-400 1 1-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Numbering on the Submodule Receptacles Each receptacle for an interface submodule has a submodule receptacle number assigned to it.
CPUs for M7-400 1 1-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.5 Memory Submodules Suitable for the Main Memory Introduction Y ou must order the MEM 478 DRAM memory submodules for the main memory of the CPUs separately .
CPUs for M7-400 1 1-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.6 Expansion Socket Introduction The CPU 486-3 and CPU 488-3 are each equipped with an expansion socket. The ISA bus is continued via the expansion socket.
CPUs for M7-400 1 1-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.3.7 Multipoint Interface (MPI) X1 Interface The X1 interface of the CPU 486-3 and CPU 488-3 for connecting devices such as PCs/programming devices is a multipoint interface (MPI) and is connected via a 9-pin sub D connector .
CPUs for M7-400 1 1-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4 The BIOS Setup Overview The BIOS setup handles the configuration of the relevant CPUs in your M7-400 system. The settings and technical information concerning the configuration of this programmable module are displayed in the BIOS setup.
CPUs for M7-400 1 1-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.1 BIOS Power Up Power Up without Error Message After switching on or after warm restart of the CPU, the BIOS (B asic I nput O utput S ystem) starts a ”P ower O n S elf T est” (POST) and displays the results in the POST window .
CPUs for M7-400 1 1-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Power Up with Error Message If one of the following errors occurs: • Memory test error • Hard disk configuration error • CMOS checksum error , the INTF LED remains lit as well as the STOP LED.
CPUs for M7-400 1 1-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.2 BIOS Hot Keys BIOS Hot Keys After power up, the BIOS offers the user a range of functions under MS-DOS.
CPUs for M7-400 1 1-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.3 Operator Inputs in the BIOS Setup Definition of the Setup Fields Within the BIOS setup, there are fields in which you can make entries or selections.
CPUs for M7-400 1 1-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Key Control within the Setup Menu The following keys are used for control within the Setup menu and .
CPUs for M7-400 1 1-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 ↑ ↓ With the cursor control keys, you can jump from line to line within a list box.
CPUs for M7-400 1 1-23 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.4 Opening and Exiting the BIOS Setup Opening the Setup Menu T o open the Setup menu, press the.
CPUs for M7-400 1 1-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Exiting the BIOS Setup T o exit the BIOS setup, activate the EXIT button shown in Figure 1 1-9 or press ESC . The “Setup Exit” dialog box then appears (see Figure 1 1-10).
CPUs for M7-400 1 1-25 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 What is the Purpose of the Setup Page? This setup page contains notes that help you to use the Setup menu. OK Button Activating this button returns to the Setup menu.
CPUs for M7-400 1 1-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Accepting Edited V alues Only the values for which the relevant interface submodule has been designed are accepted by the system in the edit boxes.
CPUs for M7-400 1 1-27 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Source Here, you set interrupts A to C (see the “Interface Submodules” chapter) provided for the interface submodule. The values positioned on the left are setpoints.
CPUs for M7-400 1 1-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 V alue (Gray T ype) Under the address set with “Config. Index”, you can now enter the configuration value. Y ou will find this value and its significance in the chapter “Interface Submodules” under the relevant interface submodule.
CPUs for M7-400 1 1-29 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.7 Setup Page “Timeout Function” Opening the Setup Page If you have selected “T imeout Function” in the Setup menu (Figure 1 1-9 on page 1 1-23) and activated the OPEN button, this setup page appears on the screen (Figure 1 1-13).
CPUs for M7-400 1 1-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 CANCEL Button Activating this button returns to the Setup menu.
CPUs for M7-400 1 1-31 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Password Enter Setup By activating this check box, you can assign a password that authorizes access to the Setup. System Boot By activating this check box, you can assign a password that permits booting of the operating system.
CPUs for M7-400 1 1-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.9 Setup Page “Date and Time” Opening the Setup Page If you have selected “Date and T ime” and activated the OPEN button in the Setup menu (Figure 1 1-9 on page 1 1-23), this BIOS setup page appears on the screen (Figure 1 1-15).
CPUs for M7-400 1 1-33 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.10 “Hard Disk” Setup Page Opening the Setup Page If you have selected “Hard Disk” and activated the OPEN button in the Setup menu (Figure 1 1-9 on page 1 1-23), this BIOS setup page appears on the screen (Figure 1 1-16).
CPUs for M7-400 1 1-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T ranslation Mode In T ranslation Mode you have four possible settings: • Auto reads the hard disk parameters and automatically sets the correct mode (Normal, LBA, Large).
CPUs for M7-400 1 1-35 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.1 1 Setup Page “Floppy/Card” Opening the Setup Page If you have selected “Floppy/Card” and activated the OPEN button in the Setup menu (Figure 1 1-9 on page 1 1-23), this setup page appears on the screen (Figure 1 1-17).
CPUs for M7-400 1 1-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.12 Setup Page “Boot Options” Opening the Setup Page If you have selected “Boot Options” and activated the OPEN button in the Setup menu (Figure 1 1-9 on page 1 1-23), this setup page appears on the screen (Figure 1 1-18).
CPUs for M7-400 1 1-37 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Halt On ... Here you can choose which error messages are displayed in an error window during booting. Displaying an error window delays booting by approximately 2 seconds.
CPUs for M7-400 1 1-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.4.13 Setup Page “System” Opening the Setup Page If you have selected “System” and activated the OPEN button in the Setup menu (Figure 1 1-9 on page 1 1-23), this setup page appears on the screen (Figure 1 1-19).
CPUs for M7-400 1 1-39 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 System Cache For the memory areas of the System ROM, the VIDEO ROM, and the addresses of BIOS expansions, you can set whether they are copied to the Shadow RAM and whether the cache should be used.
CPUs for M7-400 1 1-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1 1.5 I/O Addresses, Main Memory and Interrupt Assignments Introduction This section gives you detailed information, in the form of a table, on the I/O address space assignment, main memory and interrupt assignments of the CPUs.
CPUs for M7-400 1 1-41 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Memory Areas for A T Cards A T cards which are inserted in the expansion module A TM 478 can occupy .
CPUs for M7-400 1 1-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Assignment T able 1 1-9 Interrupt Assignment Interrupt Function NMI Group interrupt for fa.
12-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 M7-400 Expansions Chapter Overview Section Description Page 12.1 Overview 12-2 12.2 EXM 478 Expansion Module; (6ES7 478-2AC00-0AC0) 12-6 12.3 A TM 478 A T Adapter Module; (6ES7 478-2CA00-0AC0) 12-15 12.
M7-400 Expansions 12-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.1 Overview Introduction Y ou can expand your automation computer from the M7-400 range by adding expansion modules for interface submodules, short A T modules, and/or the mass storage module.
M7-400 Expansions 12-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Behavior on the S7-400 Backplane Bus The expansion modules can be accessed via the relevant programmable module and not via the S7-400 backplane bus. e.
M7-400 Expansions 12-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 e.g. FM 456-4 e.g. EXM 478 e.g. A TM 478 e.g. MSM 478 Figure 12-2 Maximum Expansion with Expansion M.
M7-400 Expansions 12-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Permissible Combinations Y ou can see from the table below which expansions can be connected to the programmable M7-400 modules.
M7-400 Expansions 12-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.2 EXM 478 Expansion Module; (6ES7 478-2AC00-0AC0) Characteristics The EXM 478 expansion module is used to house up to three interface submodules.
M7-400 Expansions 12-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.2.1 Addressing the EXM 478 Expansion Module Introduction In order to be able to program the interface submodules in the EXM 478 expansion module, you must be able to determine their addresses.
M7-400 Expansions 12-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Numbering of the Submodule Receptacles Each receptacle (slot) for an interface submodule has a submodule receptacle number assigned to it. The submodule receptacle number depends on the configuration of your CPU or FM.
M7-400 Expansions 12-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3 08 6 7 91 2 10 13 11 1 4 CPU 486-3/ CPU 488-3 EXM 478 Slot n n+2 n+3 n+4 n+1 Figure 12-5 Submodule.
M7-400 Expansions 12-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Division of Addresses in the M7-400-Specific I/O Address Area The EXM 478 expansion module is operated on the ISA bus of the programmable module.
M7-400 Expansions 12-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Addresses Within an Expansion Module Each expansion module occupies 256 bytes (100 H ) within the CPU/FM address area. The division of the 256 addresses within an expansion module can be seen from T able 12-2.
M7-400 Expansions 12-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 12-3 Base Addresses of the Interface Submodules with FM 456-4 Base Address Modules Interface Submodule in Submodule Receptacle .
M7-400 Expansions 12-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.2.2 Interrupt Assignments, Signal Switching EXM 478 Introduction Up to three interrupts per interface submodule are permitted in an EXM 478 expansion module.
M7-400 Expansions 12-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.2.3 T echnical Specifications of the EXM 478 Expansion Module T echnical Specifications of the E.
M7-400 Expansions 12-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.3 A TM 478 A T Adapter Module; (6ES7 478-2CA00-0AC0) Characteristics The A TM 478 A T adapter module is used to accommodate a short A T module (card).
M7-400 Expansions 12-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.3.1 Pin Assignments of the A T Module Pin Assignments The A TM 478 A T adapter module has a 98-pin standard direct connector for short A T modules (see Figure 12-8).
M7-400 Expansions 12-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 12-5 Pin Assignments of the 98-Pin Standard Direct Connector (A TConnector) Pin Signal Name .
M7-400 Expansions 12-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 12-5 Pin Assignments of the 98-Pin Standard Direct Connector (A TConnector), continued Pin S.
M7-400 Expansions 12-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.3.2 T echnical Specifications of the A TM 478 A T Adapter Module T echnical Specifications of th.
M7-400 Expansions 12-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example of Power Loss Calculation The following table contains a calculation example for the total power losses for an A T adapter module with an A T module.
M7-400 Expansions 12-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Permissible Dimensions of A T Modules The following illustration shows you the maximum and minimum dimensions in millimeters that A T modules must meet for the A TM 478 A T adapter module.
M7-400 Expansions 12-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.4 MSM 478 Mass Storage Module; (6ES7 478-2BA00-0AC0) Characteristics The MSM 478 mass storage module is used for storing programs and larger quantities of data.
M7-400 Expansions 12-23 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.4.1 LPT1 Parallel Port Characteristics The MSM 478 mass storage module has an A T -compatible parallel port (LPT) for connecting a printer with Centronics interface.
M7-400 Expansions 12-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 12-7 MSM 478 Parallel Port, Socket X1 (25-Pin Sub D Socket) Pin Meaning Direction 1 /STROBE .
M7-400 Expansions 12-25 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.4.2 T echnical Specifications of the MSM 478 Mass Storage Module T echnical Specifications of th.
M7-400 Expansions 12-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
13-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interface Submodules Chapter Overview Section Description Page 13.1 Interface Submodules Overview 13-2 13.2 Submodule IDs and Insertion Rules 13-4 13.3 IF 962-VGA Interface Submodule for M7-300/400; (6ES7962-1BA00-0AC0) 13-5 13.
Interface Submodules 13-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.1 Interface Submodules Overview Introduction The interface submodules are designed for use in the M7-300 and M7-400 automation computers. They can be operated in the M7-400 programmable modules and in the EXM 378/EXM 478 expansion modules.
Interface Submodules 13-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Assignments When configuring the interface submodules in the BIOS setup, you can assign ISA interrupts to the three interrupts of an interface submodule (IRQa, IRQb, IRQc).
Interface Submodules 13-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.2 Submodule IDs and Insertion Rules Submodule IDs The following table contains an overview of the submodule IDs for the interface submodules.
Interface Submodules 13-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.3 IF 962-VGA Interface Submodule for M7-300/400; (6ES7962-1BA00-0AC0) Characteristics The IF 962-VGA interface submodule is used to connect a keyboard and a VGA screen.
Interface Submodules 13-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.3.1 Pin Assignments Socket X1 VGA Screen Connection T able 13-4 Socket X1, VGA Screen Connecti.
Interface Submodules 13-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.3.2 Addressing, Interrupts, and Submodule ID Addressing Addressing corresponds to the A T standard.
Interface Submodules 13-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.3.3 T echnical Specifications T echnical Specifications The IF 962-LPT interface submodule receives its supply voltage from the M7-400 programmable modules or from the M7-300/400 expansion modules.
Interface Submodules 13-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operating Modes The WD90C24 VGA controller is used on the IF 962-VGA interface submodule. T able 13-7 shows you the video modes supported by the BIOS of the IF 962-VGA interface submodule.
Interface Submodules 13-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.4 IF 962-COM Interface Submodule for M7-300/400; (6ES7962-3AA00-0AC0) Characteristics The IF 962-COM interface submodule is used to connect devices with a serial port.
Interface Submodules 13-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.4.1 Pin Assignments Socket X1, X2 COMa, COMb T able 13-8 Socket X1, X2 IF 962-COM (9-Pin Sub.
Interface Submodules 13-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.4.2 Addressing and Interrupts Addressing The IF 962-COM interface submodule can be addressed in the following two ways: • In the A T -compatible I/O address area • In the M7-300/400-reserved I/O address area (from C000 H ).
Interface Submodules 13-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Addressing in the M7-300/400-Reserved I/O Address Ares Regardless of possible addresses in the A T -compatible I/O address area, the IF 962-COM interface submodule can be addressed in this reserved address area.
Interface Submodules 13-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 13-13 Meaning of the Addressing T ype Bits in the Configuration Register (IF 962-COM) I/O.
Interface Submodules 13-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Request The interface submodule supplies an interrupt request (IRQa and IRQb) for each serial port.
Interface Submodules 13-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.5 IF 962-LPT Interface Submodule for M7-300/400; (6ES7962-4AA00-0AC0) Characteristics The IF 962-LPT interface submodule contains an A T -compatible parallel (LPT) port for connecting a printer with Centronics interface.
Interface Submodules 13-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.5.1 Pin Assignments X1 Socket T able 13-15 Socket X1, IF 962-LPT (25-Pin Sub D Socket Connect.
Interface Submodules 13-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.5.2 Addressing and Interrupts Addressing The IF 962-LPT interface submodule can be addressed .
Interface Submodules 13-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example of Setting an A T -Compatible I/O Address In the following example, the I/O address 0278 H is to be set in the BIOS setup. Proceed as follows to do this: 1.
Interface Submodules 13-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Default Settings in the BIOS The following I/O addresses and interrupt numbers are set as defaults in the BIOS for LPT ports: Port I/O Address Interrupt No.
Interface Submodules 13-21 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 13-20 Meaning of the Addressing T ype Bits in the Configuration Register (IF 962-LPT) I/O.
Interface Submodules 13-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.5.3 T echnical Specifications T echnical Specifications The IF 962-LPT interface submodule receives its supply voltage from the M7-400 programmable modules or from the M7-300/400 expansion modules.
Interface Submodules 13-23 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.6 IF 961-DIO Interface Submodule for M7-300/400; (6ES7961-1AA00-0AC0) Characteristics The IF 961-DIO interface submodule has the following characteristics: • 8 inputs, isolated in groups of 2 Input level 24 VDC; 8.
Interface Submodules 13-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.6.1 Pin Assignments X1 Socket There is a 25-pin sub D socket connector on the frontside of the submodule for plugging in the connecting cable. Figure 13-6 shows the pin assignments of the submodule.
Interface Submodules 13-25 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Figures 13-7 and 13-8 show the circuit block diagrams and the terminal connection diagrams for wiring the digital inputs and digital outputs.
Interface Submodules 13-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.6.2 Addressing and Interrupts Addressing in the M7-300/400-Reserved I/O Address Area The base address depends on the interface submodule slot in the expansion module or the programmable module.
Interface Submodules 13-27 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Digital Output Function T ables 13-24 and 13-25 give an overview of the digital output function.
Interface Submodules 13-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Register The cause of the interrupt is stored in this register .
Interface Submodules 13-29 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Selection Register Rising Edge T ables 13-32 and 13-33 give an overview of the selection register for interrupt generation at a rising edge of a digital input.
Interface Submodules 13-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Mode Register T ables 13-36 and 13-37 give an overview of the mode register .
Interface Submodules 13-31 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.6.3 T echnical Specifications T echnical Specifications The IF 961-DIO interface submodule receives its supply voltage from the M7-400 programmable modules or from the M7-300/400 expansion modules.
Interface Submodules 13-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Status indicated Interrupt Diagnostic functions – 1 sum interr.
Interface Submodules 13-33 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7 IF 961-AIO Interface Submodule for M7-300/400; (6ES7961-2AA00-0AC0) Characteristics The IF .
Interface Submodules 13-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.1 Pin Assignments and T erminal Connection Diagram X1 Socket There is a 25-pin sub D socket connector on the frontside of the submodule for plugging in the connecting cable.
Interface Submodules 13-35 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Meaning of Signals The following table shows the meanings of the signals in Figure 13-10. T able 13-38 Meaning of the Signals of the X1 Socket of the IF 961-AIO Interface Submodule Signal Meaning MV 0+ .
Interface Submodules 13-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Grounding for the Analog Inputs If the valid Common Mode area (V CM ) cannot be retained, the analog inputs must be grounded.
Interface Submodules 13-37 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.2 Connecting Measured V alue Sensors to Analog Inputs Introduction Depending on the measuri.
Interface Submodules 13-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Isolated Measured V alue Sensors Potential differences can occur between the individual measured value sensors in the case of isolated measured value sensors.
Interface Submodules 13-39 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Non-Isolated Measured V alue Sensors Potential differences must not arise between non-isolated measured value sensors. If necessary , you must take additional installation measures (equipotential bonding conductor) to ensure this.
Interface Submodules 13-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connection of Current Sensors as T wo-Wire and Four-Wire T ransducers Figures 13-16 and 13-17 show you how to connect current sensors as two-wire and four-wire transducers to analog input modules.
Interface Submodules 13-41 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connection of Resistance Thermometers (e.g. Pt 100) and Resistances The resistance thermometers/resistances are measured in a 4-wire connection.
Interface Submodules 13-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.3 Connecting Loads/Actuators to Analog Outputs Abbreviations Used The abbreviations used in.
Interface Submodules 13-43 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connecting Loads to the V oltage Output The following figure shows the wiring of two channels as an example.
Interface Submodules 13-44 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.4 Conversion Time and Cycle Time of the Analog Input Channels Introduction This section contains the definitions of and relationships between the conversion time and the cycle time of analog input modules.
Interface Submodules 13-45 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.5 Conversion Time, Cycle T ime, Settling Time, and Response Time of the Analog Output Channels Introduction This section contains the definitions and relationships of times relevant to the analog output modules.
Interface Submodules 13-46 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.6 Starting Up the IF 961-AIO Interface Submodule Electrical Installation Y ou must connect the ground terminal (M and S 0/ S 1 ) of the analog input/output module with the ground terminal of the load power supply .
Interface Submodules 13-47 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.8 Analog Output Function Analog Output Function The 12-bit digital value to be converted is loaded left-justified into the DAC data registers of the relevant DAC channel.
Interface Submodules 13-48 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.9 Analog Input Function Analog Input Function T ables 13-41 ad 13-42 contain an overview of the read and write registers for the analog input function.
Interface Submodules 13-49 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T able 13-42 Meaning of the Control Bits in the Analog Input Function (IF 961-AIO) Offset Address D15 Writing D0 Remark 08 H A C I N T 0 0 0 0 0 0 0 0 0 0 0 ta ta ta Control register 1 0A H 0 000000000000 ADC channel no.
Interface Submodules 13-50 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Cyclic Conversion of the ADC Channels Below are listed the steps required for cyclic conversion of the ADC channels: 1. Set the AC bit in control register 1 to “1” (offset address “08 H ”).
Interface Submodules 13-51 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.10 Analog V alue Representation for the Measuring Ranges of the Analog Inputs V oltage and .
Interface Submodules 13-52 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.1 1 Analog V alue Representation for the Measuring Ranges of the Analog Outputs V oltage and Current Output Ranges T able 13-44 contains the representation of • The voltage output range ± 10 V and • The current output range ± 20 mA.
Interface Submodules 13-53 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.12 Diagnostics, Interrupts, and Submodule ID Interrupt Request The interface submodule supplies an interrupt request (IRQa).
Interface Submodules 13-54 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.13 T echnical Specifications T echnical Specifications The IF 961-AIO interface submodule receives its supply voltage from the M7-400 programmable modules or from the M7-300/400 expansion modules.
Interface Submodules 13-55 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interference Suppression, Error Limits for Inputs Interference voltage suppression for f = n (50/60 Hz " 1 %) n = 1, 2, .
Interface Submodules 13-56 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.8 IF 961-CT1 Interface Submodule for M7-300/400; (6ES7961-3AA00-0AC0) Characteristics The IF 961-CT1 interface submodule is used for connecting incremental encoders.
Interface Submodules 13-57 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.8.1 What Can the IF961-CT1 Interface Submodule Do? Introduction This section contains an overview of the functionality of the IF 961-CT1 interface submodule.
Interface Submodules 13-58 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupts The IF 961-CT1 can initiate an interrupt when comparison values are reached or in the event of overflow , underflow , or zero pass of the counter .
Interface Submodules 13-59 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.8.2 Addressing and Interrupts Addressing The IF 961-CT1 interface submodule is addressed with the M7-300/400-reserved I/O address area (starting from C000 H ).
Interface Submodules 13-60 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.8.3 T echnical Specifications T echnical Specifications The IF 961-CT1 interface submodule receives its supply voltage from the M7-400 programmable modules or from the M7-300/400 expansion modules.
Interface Submodules 13-61 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.9 IF 964-DP Interface Submodule for S7-400 and M7-400 Order Numbers Y ou can use the IF 964-DP interface submodule with order number 6ES7964-2AA00-0AB0 (up to 07/99) in the M7-400.
Interface Submodules 13-62 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Additional Front Cover The IF 964-DP interface submodule with order number 6ES7964-2AA01-0AB0 has an additional front cover , which is similar to the front cover of the IF 960HF synchronization submodule.
Interface Submodules 13-63 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.9.1 Pin Assignments X1 Connector There is a 9-pin sub D socket connector on the frontside of the submodule for plugging in the connecting cable.
Interface Submodules 13-64 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.9.2 Addressing and Interrupts In the M7-300/400-Reserved I/O Address Area The base address depends on the interface submodule slot in the expansion module or the programmable module.
Interface Submodules 13-65 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.9.3 T echnical Specifications T echnical Specifications The IF 964-DP interface submodule receives its supply voltage in the S7-400 from the central processing unit and in the M7-400 from the programmable modules or from the expansion modules.
Interface Submodules 13-66 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
A-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Parameter Sets for Signal Modules Chapter Overview Section Description Page A.1 How to Assign the Parameters for Signal Modules in the User Program A-2 A.2 Parameters of the Digital Input Modules A-4 A.
Parameter Sets for Signal Modules A-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A.1 How to Assign the Parameters for Signal Modules in the User Program Parameter Assignment in the User Program Y ou have already assigned parameters to the modules in STEP 7 .
Parameter Sets for Signal Modules A-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Description of the Parameters The following sections contain all the modifiable parameters for the various module classes. The parameters of the signal modules are described: • in the online help of STEP 7 .
Parameter Sets for Signal Modules A-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A.2 Parameters of the Digital Input Modules Parameters The table below contains all the parameters you can set for digital input modules.
Parameter Sets for Signal Modules A-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Byte 0 76 0 Hardware interrupt enable Diagnostic interrupt enable Byte 1 76 0 On risi.
Parameter Sets for Signal Modules A-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 The figure below shows the structure of data record 1 (bytes 4, 5 and 6) for the parameters of the digital input modules. Y ou enable a parameter by setting the corresponding bit to “1”.
Parameter Sets for Signal Modules A-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A.3 Parameters of the Digital Output Modules Parameters The table below contains all the parameters you can set for digital output modules.
Parameter Sets for Signal Modules A-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Structure of Data Record 1 The figure below shows the structure of data record 1 (bytes 0, 1 and 2) for the parameters of the digital output modules.
Parameter Sets for Signal Modules A-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 The figure below shows the structure of data record 1 (bytes 3 and 4) for the parameters of the digital output modules. Y ou enable a parameter by setting the corresponding bit to “1”.
Parameter Sets for Signal Modules A-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A.4 Parameters of the Analog Input Modules Parameters The table below contains all the parameters you can set for analog input modules.
Parameter Sets for Signal Modules A-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Structure of Data Record 1 The figure below shows the structure of data record 1 for the parameters of the analog input modules. Y ou enable a parameter by setting the corresponding bit to “1”.
Parameter Sets for Signal Modules A-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
B-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Diagnostic Data of the Signal Modules Chapter Overview Section Description Page B.1 Evaluating the Diagnostic Data of the Signal Modules in the User Program B-2 B.2 Structure and Contents of Diagnostic Data Bytes 0 and 1 B-3 B.
Diagnostic Data of the Signal Modules B-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.1 Evaluating the Diagnostic Data of the Signal Modules in the User Program In This Appendix This Appendix describes the structure of the diagnostic data in the system data.
Diagnostic Data of the Signal Modules B-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.2 Structure and Contents of Diagnostic Data Bytes 0 and 1 The structure and contents of the different bytes of the diagnostic data are described below .
Diagnostic Data of the Signal Modules B-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.3 Diagnostic Data of the Digital Input Modules as of Byte 2 The structure and contents of the different bytes of the diagnostic data for special digital input modules are described below .
Diagnostic Data of the Signal Modules B-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 4 to 8 of the SM 421; DI 16 24 VDC Byte 4 76 0 5 4321 Byte 5 70 Channel typ.
Diagnostic Data of the Signal Modules B-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 2 and 3 of the SM 421; DI 16 24/60 VUC Byte 2 76 0 Operating status 0: RUN .
Diagnostic Data of the Signal Modules B-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 9 to 24 of the SM 421; DI 16 24/60 VUC Data record 1 with bytes 9 to 24 contains the channel-specific diagnostic data. The figure below shows the assignment of the diagnostic byte for a channel of the module.
Diagnostic Data of the Signal Modules B-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.4 Diagnostic Data of the Digital Output Modules as of Byte 2 The structure and contents of the different bytes of the diagnostic data for special digital output modules are described below .
Diagnostic Data of the Signal Modules B-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 4 to 8 of the SM 422; DO 16 20-125 VDC/1.
Diagnostic Data of the Signal Modules B-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 2 and 3 of the SM 422; DO 32 24 VDC/0.
Diagnostic Data of the Signal Modules B-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 4 to 10 of the SM 422; DO 32 24 VDC/0.
Diagnostic Data of the Signal Modules B-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 1 1 to 42 of the SM 422; DO 32 24 VDC/0.5 A Data record 1 with bytes 1 1 to 42 contains the channel-specific diagnostic data.
Diagnostic Data of the Signal Modules B-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 4 to 8 of the SM 422; DO 16 20-120 V AC/2 A Byte 4 76 0 5 4321 Byte 5 70 C.
Diagnostic Data of the Signal Modules B-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.5 Diagnostic Data of the Analog Input Modules as of Byte 2 The structure and contents of the different bytes of the diagnostic data for the special analog input modules are described below .
Diagnostic Data of the Signal Modules B-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 4 to 8 of the SM 431; AI 16 16 Bit Byte 4 76 0 5 4321 Byte 5 70 Channel ty.
Diagnostic Data of the Signal Modules B-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 2 and 3 of the SM 431; AI 8 RTD 16 Bit Byte 2 76 0 Operating status 0: RUN.
Diagnostic Data of the Signal Modules B-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 8 to 23 of the SM 431; AI 8 RTD 16 Bit Data record 1 with bytes 8 to 23 contains channel-specific diagnostic data.
Diagnostic Data of the Signal Modules B-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 2 and 3 of the SM 431; AI 8 16 Bit Byte 2 76 0 Operating status 0: RUN 1: .
Diagnostic Data of the Signal Modules B-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bytes 8 to 23 of the SM 431; AI 8 16 Bit Data record 1 with bytes 8 to 23 contains channel-specific diagnostic data.
Diagnostic Data of the Signal Modules B-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
C-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Spare Parts and Accessories Spare Parts and Accessories For Racks Number wheel for slot labeling C79165-Z1523-A22 Spare.
Spare Parts and Accessories C-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 For IMs T erminating connector for IM 461-0 6ES7461-0AA00-7AA0 T erminating connector for I.
Spare Parts and Accessories C-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Cables Connecting cables for printers with • Serial port (COM, 10 m) • Parallel port (C.
Spare Parts and Accessories C-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07.
D-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Guidelines for Handling Electrostatic Sensitive Devices (ESD) Introduction In this appendix, we explain • what is meant by “electrostatic sensitive devices” • the precautions you must observe when handling and working with electrostatic sensitive devices.
Guidelines for Handling Electrostatic Sensitive Devices (ESD) D-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 D.1 What is ESD? Definition All electronic modules are equipped with large-scale integrated ICs or components.
Guidelines for Handling Electrostatic Sensitive Devices (ESD) D-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 D.2 Electrostatic Charging of Persons Charging Every person with a non-conductive connection to the electrical potential of its surroundings can be charged electrostatically .
Guidelines for Handling Electrostatic Sensitive Devices (ESD) D-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 D.3 General Protective Measures Against Electrostatic Dis.
E-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 List of Abbreviations Abbreviation Explanation AC Alternating current ADC Analog to digital converter AI Aanalog input .
List of Abbreviations E-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 FC Function FEPROM Flash erasable programmable read only memory FM Function module FOC Fiber-opti.
List of Abbreviations E-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 S + Sensor lead (positive) S – Sensor lead (negative) SCL Structured control language SP Sensor.
.
Glossary-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Glossary Address An address denotes a specific operand or address area; examples of this are: input I 12.1; memory word MW 25; data block DB 3. Aggregate current Sum of the currents of all output channels on a digital output module.
Glossary Glossary-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bus connector A physical connection between the bus nodes and the bus cable. Bus segment A bus segment is a self-contained section of a serial bus system.
Glossary Glossary-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Comparison point Parameter in STEP 7 for analog input modules. Using this parameter , you can determine the reference junction (the point where the temperature is known) when thermocouples are used.
Glossary Glossary-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Declaration Assigning variables (parameters or local data of a block, for example) with a name, data type, comment, etc. Default setting The default setting is a sensible basic setting that is used whenever no other value is used.
Glossary Glossary-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Direct communication Direct communication involves assigning local input address areas of an intelligent DP slave (for example, CPU 315-2 with PROFIBUS DP connection) or of a DP master to the input address areas of a PROFIBUS DP partner .
Glossary Glossary-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Equipotential bonding An electrical connection (equipotential bonding conductor) that brings the bodies.
Glossary Glossary-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function A function (FC) in accordance with IEC 1 131-3 is a ³ code block without ³ static data. A function allows parameters to be passed in the user program.
Glossary Glossary-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Ground, to T o ground means to connect an electrically conductive part via a grounding system to the grounding electrode (one or more conductive parts having a very good contact to ground).
Glossary Glossary-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt, diagnostic ³ Diagnostic Interrupt Interrupt, end-of-scan-cycle ³ Hardwareinterrupt Interru.
Glossary Glossary-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Local data Local data are data assigned to a ³ code block that is declared in its ³ declaration section and its variable declaration. It includes (depending on the block): formal parameters, ³ static data, ³ temporary data.
Glossary Glossary-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Measuring range module Measuring range modules are plugged into the analog input modules for adaptation to different measuring ranges. Memory card Pluggable load memory .
Glossary Glossary-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Non-isolated In the case of non-isolated input/output modules, the reference potentials of the control and load circuit are electrically connected.
Glossary Glossary-13 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Priority class The operating system of an S7 CPU has a maximum of 28 priority classes (= program execution levels) – for cyclic program scanning or program scanning controlled by hardware interrupt, for example.
Glossary Glossary-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Programming device A programming device (PG) is an industry-standard, compact personal computer . A PG is completely equipped for programming SIMA TIC programmable controllers.
Glossary Glossary-15 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Reference channel error Parameter in STEP 7 for analog input modules. Using this parameter , you can enable the group error message of the reference junction when thermocouples are used.
Glossary Glossary-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Restart When a CPU starts up (through the use of the mode selector , for example, or when the power is switched on), either OB 101 (restart), OB 100 (reboot: warm restart) or OB 102 (cold restart) is processed before cyclic program scanning (OB 1).
Glossary Glossary-17 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Sequence layer Sequence layers form the interface in M7 between the operating system of the CPU and the user program. The order in which the blocks of the user program are processed is defined in the sequence layers.
Glossary Glossary-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 ST ARTUP The ST ARTUP mode is traversed during the transition from ST OP mode to RUN mode. ST ARTUP can be triggered by the ³ mode selector or following power-on or by means of an operator input on the programming device.
Glossary Glossary-19 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 System function block A system function block (SFB) is a ³ function block integrated in the operating system of the CPU that can be called in the STEP 7 user program like a function block (FB), as required.
Glossary Glossary-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 W arm restart This is a reboot after a power failure using a set of dynamic data programmed by the user and a user program section defined in the system.
Index-1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Index A Accessories, C-1 Accessories, M7-400, memory card, 1 1-8 Actuator connection, to analog output module, 5-59.
Index Index-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog output channel conversion time, 5-37 response time, 5-38 Analog output module connecting loads and act.
Index Index-3 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Communication bus, 2-5 Communication load, Glossary-2 Communication processor , Glossary-2 Comparison point, 5-57, Glossary-3 Compensating box, 5-55, Glossary-3 connecting, 5-56 Compensation external, 5-55 internal, 5-55, 5-56 Config.
Index Index-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Diagnostics analog input module, 5-40 digital input module, 4-7 digital output module, 4-8 of analog modules,.
Index Index-5 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Digital output module destination CPU for Interrupt, 4-8 diagnostic data, B-8 diagnostic interrupt enable, 4-.
Index Index-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Functional grounding, Glossary-7 Fuse blown, Glossary-7 digital module, 4-12 digital output module, 4-8 G Glo.
Index Index-7 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 IF 962-LPT , 13-16 addressing, 13-18 A T -compatible, 13-18 M7-300/400 reserved, 13-19 characteristics, 13-16.
Index Index-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt-triggering channels, of the digital module, 4-14 Interrupts enabling, 4-13, 5-67 of analog modules,.
Index Index-9 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Non-isolated sensors, 5-45 connecting, 5-45 O OB, Glossary-12 OB 40, 4-14, 5-68 start information, 5-68 OB 82.
Index Index-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 P ARM_MOD, SFC 57, A-2 Password, M7-400, 1 1-31 Performance features, M7-400, CPUs, 1 1-2 Permissible potent.
Index Index-1 1 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Sensor supply missing digital input module, 4-7 digital module, 4-12 Sensors, non-isolated, 5-45 Sequence l.
Index Index-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T T echnical specifications IF 961-AIO, 13-54 IF 961-DIO, 13-31 IF 962-COM, 13-15 IF 962-LPT , 13-22 IF 962-.
デバイスSiemens S7-400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Siemens S7-400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSiemens S7-400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Siemens S7-400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Siemens S7-400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Siemens S7-400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSiemens S7-400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Siemens S7-400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSiemens S7-400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
