Snapperメーカー18HP, 19HPの使用説明書/サービス説明書
ページ先へ移動 of 36
OPERA T OR’S MANU AL 18HP Zero-T urn Riders Mfg. No. Description 1694454 Simplicity 18HP Consumer Zero T urn Rider 5091000 Snapper F ast Cut ZT18440KH, 18HP Zero-T urn Rider with 44” Mow er 1694744 Massey F erguson ZT 1844 20HP Zero-T urn Riders Mfg.
T able of Contents 1 W ARNING Engine exhaust fr om this product contains chemicals kno wn, in cer tain quantities, to cause cancer , bir th defects, or other reproductive harm. T roubleshooting, Adjustments & Service .......21 T roub leshooting the Rider .
2 GENERAL OPERA TION 1. Read, understand, and f ollow all instructions in the manual and on the unit bef ore star ting. 2. Do not put hands or f eet near rotating par ts or under the machine.
3 CHILDREN T ragic accidents can occur if the operator is not aler t to the presence of children. Children are often attracted to the unit and the mowing activity . Ne ver assume that children will remain where you last sa w them. 1. K eep children out of the mowing area and under the watchful care of another responsib le adult.
4 Safety Rules and Information SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars , pipes, and other sources of ignition. 2. Use only approv ed gasoline containers. 3. Ne ver remo ve the gas cap or add fuel with the engine running.
Unit ID T ag Mower ID T ag Identification Numbers 5 When contacting your authorized dealer f or replace- ment parts, service, or information y ou MUST have these numbers. Record your model name/n umber , manuf acturer’ s identi- fication numbers , and engine serial numbers in the space provided f or easy access.
Safety Decals 6 SAFETY DECALS This unit has been designed and manuf actured to pro- vide you with the saf ety and reliability you would e xpect from an industr y leader in outdoor pow er equipment manuf actur ing.
Safety Icons & Interlock System 7 SAFETY INTERLOCK SYSTEM This unit is equipped with saf ety interlock s witches. These saf ety systems are present f or your saf ety , do not attempt to bypass saf ety switches , and ne ver tamp- er with saf ety de vices.
Features & Controls 8 Ground Speed Le vers These le vers control the g round speed of the rider . The left le ver controls the left rear driv e wheel and the right controls the right rear dr iv e wheel. Moving a le ver f orward increases the FORW ARD speed of the associated wheel, and pulling back on a le ver increases the REVERSE speed.
Features & Controls 9 Ignition Switch The ignition s witch star ts and stops the engine; it has three positions: OFF Stops the engine and shuts off the electrical system. R UN Allows the engine to run and powers the electrical system. ST ART Cranks the engine f or star ting.
Do not load this zero-turn rider on a trailer or truck using tw o separate ramps. Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider . This rider has a zero turning radius and the rear wheels could fall off the ramps, or the rider could tip over injuring the operator or b ystanders.
Operation 11 W ARNING If you do not under stand how a specific control functions, or have not yet thor oughly read the FEA TURES & CONTROLS section, do so now . Do NO T attempt to operate the rider without first becoming familiar with the location and function of ALL controls.
Operation 12 ZER O TURN DRIVING PRA CTICE The le ver controls of the z ero tur n r ider are responsiv e, and learning to gain a smooth and efficient control of the rider’ s f orward, re verse, and turning mov ements will take some practice.
Operation 13 AD V ANCED DRIVING Executing an End-Of-Ro w Zero T urn Y our zero turn r ider’ s unique ability to tur n in place allows y ou to turn around at the end of a cutting row rather than ha ving to stop and Y - tur n bef ore star ting a new row .
Operation 14 (91kg) 200 Lbs. 10˚ 3'4" (1m) 20' (6m) Figure 9. T railer Weight Recommendations A. Clevis Pin B. Clip A B A TT A CHING A TRAILER The maximum weight of a to wed trailer should be less than 200 lbs (91kg). Secure the trailer with an appropri- ately sized cle vis pin (A, Figure 9) and clip (B).
Operation 15 MO WER REMO V AL AND INST ALLA TION NO TE: P erform mower installation and remo v al on a hard flat surf ace such as a concrete floor . Remov al 1. Disengage the PT O, engage the parking brak e, turn off the ignition, remov e the key , and wait for all mo v- ing par ts to stop .
Regular Maintenance 16 MAINTENANCE SCHEDULE & PR OCEDURES The f ollowing schedule should be f ollowed f or nor mal care of y our rider and mower . Y ou will need to keep a record of your oper ating time. Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter .
Regular Maintenance 17 Oil: • control handle pivots • discharge chute hinge Generally , all moving metal par ts should be oiled where contact is made with other par ts. K eep oil and grease off belts and pulleys . Remember to wipe fittings and sur- f aces clean both bef ore and after lubrication.
Regular Maintenance 18 SER VICING THE MO WER BLADES Service Interval: Every 10 Hours or As Required 1. Remov e mower deck (see “Mower Dec k Removal”). 2. See Figure 13. T o remove b lade for sharpening, use a bloc k of wood to prev ent blade rotation while loos- ening the capscrew .
CHECK TIRE PRESSURES Tire pressure should be check ed per iodically , and main- tained at the le vels sho wn in the char t. Note that these pressures ma y diff er slightly from the “Max Inflation” stamped on the side-wall of the tires . The pressures shown pro vide proper traction, improv e cut quality , and e xtend tire lif e.
Regular Maintenance 20 3. Add oil up to the full mark (D , Figure 18). 4. Reinstall the reser v oir cap , mov e the locking tab between two notches , and tighten the locking cap- screw . TRANSMISSION OIL FIL TER CHANGE Change Interval: Every 250 Hours Filter P art Number: 1719168 1.
T roubleshooting, Adjustments, & Service 21 TR OUBLESHOO TING While normal care and regular maintenance will extend the lif e of your equipment, prolonged or constant use ma y e ventually require that service be performed to allow it to continue operating properly .
22 Rider T roubleshooting Continued. PROBLEM CA USE REMED Y Engine runs, but rider will 1. Hydraulic release v alve(s) 1. T ur n v alve(s) cloc kwise to close. not drive. in “open” position. 2. Belt is broken. 2. See Drive Belt Replacement. 3. Drive belt slips.
23 T roubleshooting, Adjustments, & Service SEA T ADJUSTMENTS The seat and ground speed control le vers should be adjusted so that operator’ s elbows are suppor ted b y the ar m rests when his/h.
T roubleshooting, Adjustments, & Service 24 Figure 22. Cutting Height Adjustment A. Cutting Height Adjustment Pin B. Deck Lift / Cutting Height Le ver C. T ranspor t Release Le ver B C A CUTTING HEIGHT ADJUSTMENT The cutting height adjustment pin (A, Figure 22) controls the mower cutting height.
2" 3/16" T roubleshooting, Adjustments, & Service 25 Figure 23. Parking Brake Adjustment A. Brake Spring B. Set Collar C. Lockn ut P ARKING BRAKE ADJUSTMENT Brake Adjustment 1. Disengage the PT O, stop the engine , bloc k the front wheels, remo ve the ignition k ey , and engage the parking brake .
T roubleshooting, Adjustments, & Service 26 W ARNING T o av oid serious injur y , perf orm adjustments only with engine stopped, key removed and rider on level gr ound. B A C A B B B Figure 25. PTO Clutc h Adjustment A. Adjustment Window (Qty . 3, one shown) B.
T roubleshooting, Adjustments, & Service 27 MO WER DECK LEVELING P erform these adjustments on a flat lev el surface . Note: Do not adjust the mower lift height rod (H, Figure 29) as it will eff ect the mower dec k lift height. SIDE-T O-SIDE LEVELING 1.
T roubleshooting, Adjustments, & Service 28 R OLLER B AR LEVELING (If Equipped) 1. First le vel the mo wer deck using the procedure f ound in MO WER DECK LEVELING. 2. With the mower installed, place the rider on a smooth, le vel surf ace such as a concrete floor .
T roubleshooting, Adjustments, & Service 29 HYDRA ULIC PUMP DRIVE BEL T REPLA CEMENT 1. P ar k the rider on a smooth, lev el surface such as a concrete floor . Disengage the PT O , engage the par k- ing brak e, turn off the engine, and remov e the ignition key .
MO WER BEL T REPLA CEMENT 1. P ar k the rider on a smooth, lev el surface such as a concrete floor . Disengage the PT O , engage the par k- ing brak e, turn off the engine, and remov e the ignition key . 2. Remov e the capscrews securing the left and r ight belt cov ers (A, B Figure 34) and remove the co vers .
Specifications 31 ENGINE: 18 HP* K ohler Make K ohler Model Command PRO 18 Horsepower 18 @ 3400 rpm Displacement 30.08 Cu. in (493 cc) Electrical System 12 V olt, 15 amp.
Parts & Accessories 32 REPLA CEMENT P ARTS Replacement par ts are av ailable from your authorized dealer . Alwa ys use genuine Simplicity/Snapper Ser vice Pa r t s . TECHNICAL MANU ALS Additional copies of this manual are a vailab le, as well as fully illustrated par ts lists.
Lawn Care & Mowing Information LC-1 HO W AND WHEN T O W A TER, FERTILIZE & AERA TE Most lawns are watered too often, but with too little water.
LC-2 Lawn Care & Mowing Information WHEN AND HO W OFTEN T O MO W The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: ● Mow when the grass is between 3”-4” (7,5-10 cm) high.
MANUF ACTURING, INC . 500 N Spring Street / PO Box 997 P or t Washington, WI 53074-0997 www .simplicitymfg.com © Cop yright 2004, Simplicity Manufacturing, Inc. All Rights Reser v ed. Printed in USA. PRODUCTS , INC. McDonough, GA., 30253 www .snapper .
デバイスSnapper 18HP, 19HPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper 18HP, 19HPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper 18HP, 19HPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper 18HP, 19HPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper 18HP, 19HPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper 18HP, 19HPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper 18HP, 19HPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper 18HP, 19HPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper 18HP, 19HPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
