Axxess InterfaceメーカーAutomobile Accessoriesの使用説明書/サービス説明書
ページ先へ移動 of 12
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORA TION 1-800-221-0932 axxessinterf ace.com INST ALLA TION INSTRUCTIONS FOR PART RF ASWC The RF ASWC is designed for adding steering wheel controls to vehicles that do not have OE steering wheel controls installed.
Mounting The RF ASWC T ransmitter 1. Place button pad in the OESWC transmitter with the volume up arrow (^) in the spot where you want volume up to be.
Wiring The OESWC Interface 1. Connect the red wire to 12 volt accessory 2. Connect the Black wire to ground (you may use the same ground that you use for the aftermarket radio) If you are using an Eclipse or Kenwood radio, plug the female 3.5mm connector with the Brown and Brown/White wires into the male 3.
2. T urn on the ignition and press volume up on the RF ASWC. This will “marry“ the RF ASWC to the interface. NOTE: If you are replacing a transmitter you must turn on the ignition and within the rst 10 seconds press and hold the source button for ten seconds.
5. The led will then ash up to 10 times. 6. This is the end of the auto detection stage. If the RF ASWC detected the radio successfully the led will light up solid red. 7. Make sure the steering wheel control buttons function correctly in the vehicle and enjoy your radio.
Once all the information above has been veried and correct, refer back to the 2 sets of led ashes during the auto detect sequence. Here is what the ashes stand for: LED Feedback The led ashes represent what brand radio the RF ASWC believes it is connected to.
Remapping the SWC Buttons Let’s say you have the RF ASWC programmed to your radio and you want to change the button assignment for the steering wheel controls. For instance you would like Seek Up to be Mute. NOTES: • The RF ASWC must have detected the radio it is attached to before you can remap any buttons.
5. Follow the list below in order however pushing the steering wheel control button you want for the function below . If you want to skip a command press the V olume Up on the steering wheel, this will tell the ASWC to skip the command and go to the next one.
* Note: Remember not all radios will have all these commands. Please refer to the radios’ owners manual for specic commands recognized by the radio. For instance the next command to be mapped is the V olume Down command. Let’s say you want the Mode button on your steering wheel to be the V olume Down command.
2. The led will turn on then release the V olume Down button and the led will turn off. 3. The original steering wheel control settings will be restored.
4. If you have a different radio then Eclipse, press the V olume Up button again till the led goes solid red, then release V olume Up. Y ou have now programmed Kenwood.
REV . 1/10/1 1 1-800-221-0932 axxessinterf ace.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORA TION INST ALLA TION INSTRUCTIONS FOR PART RF ASWC K NO WLEDGE IS P OW ER E nhance your installation and fabrication skills by enrolling in the most re cognized and re spected mobile electronics school in our industry .
デバイスAxxess Interface Automobile Accessoriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Axxess Interface Automobile Accessoriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAxxess Interface Automobile Accessoriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Axxess Interface Automobile Accessoriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Axxess Interface Automobile Accessoriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Axxess Interface Automobile Accessoriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAxxess Interface Automobile Accessoriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Axxess Interface Automobile Accessoriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAxxess Interface Automobile Accessoriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。