SonyメーカーMDS-JE770の使用説明書/サービス説明書
ページ先へ移動 of 72
MDS-JE770 SPECIFICA TIONS SERVICE MANUAL MINIDISC DECK Model Name Using Similar Mechanism MDS-S50 MD Mechanism T ype MDM-7A Optical Pick-up T ype KMS-260B/260E AEP Model UK Model E Model F oreign patents licensed form Dolby Laboratories Licensing Corporation.
2 MDS-JE770 SELF-DIA GNOSIS FUNCTION The self-diagnosis function consists of error codes for customers which are displayed automatically when errors occur , and error codes which show the error history in the test mode during servicing. For details on how to view error codes for the customer , refer to the following box in the instruction manual.
3 MDS-JE770 ITEMS OF ERR OR HISTOR Y MODE ITEMS AND CONTENTS Selecting the T est Mode Displa y op rec tm op play tm spdl rp tm retry err total err err history retry adrs er refresh tm change op change Histor y Displays the total recording time.
4 MDS-JE770 P ARTS No. 4-233-025-6 s 4-236-047-1 s 4-233-025-8 s Description T able of Error Codes Error Code 10 12 20 21 22 23 24 30 31 40 41 42 43 50 51 Could not load Loading switches combined inco.
5 MDS-JE770 SECTION 1 SER VICE NO TES This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior . Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
6 MDS-JE770 JIG FOR CHECKING BD BO ARD W A VEFORM The special jig (J-2501-196-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to be performed are shown as follows.
7 MDS-JE770 Iop D A T A RECORDING AND DISPLA Y WHEN OPTICAL PICK-UP AND NON-V OLA TILE MEMOR Y (IC195 OF BD BO ARD) ARE REPLA CED The Iop value labeled on the optical pick-up can be recorded in the non-volatile memory . By recording the value, it will eliminate the need to look at the value on the label of the optical pick-up.
8 MDS-JE770 OPTICAL PICK-UP BLOCK TYPE DISCRIMINA TION There are two types of the optical pick-up block in this model. These are compatible except for the laser power . Check the type of the optical pick-up block before replacement. Ajdust following items after replacing the optical pick-up block.
9 MDS-JE770 CHECKS PRIOR T O PARTS REPLA CEMENT AND ADJUSTMENTS Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent. Details of the procedures are described in “5 Electrical Adjustments”.
10 MDS-JE770 Fig. 2 Reading the T est Mode Displa y (During playbac k) @@###**$$ Fluorescent display tube display @@ : Parts No. (name of area named on T OC) ### : Cluster ** : Sector $$ : T rack mode.
11 MDS-JE770 Hexadecimal Bit Binar y Higher Bits Lo wer Bits 84218421 b7 b6 b5 b4 b3 b2 b1 b0 00000001 00000010 00000100 00001000 00010000 00100000 01000000 10000000 Hexa- decimal Details 01 02 04 08 10 20 40 80 Emphasis OFF Monaural This is 2-bit display .
12 MDS-JE770 SECTION 2 GENERAL This section is e xtracted from instruction manual. Parts Identification The i tems ar e ar ranged in al phabet ical o rder .
13 MDS-JE770 SECTION 3 DISASSEMBL Y 3-1. DISASSEMBL Y FLO W • This set can be disassembled in the order shown below . SET 3-2 UPPER CASE (408226) 3-3 FRONT P ANEL SECTION 3-4 MAIN BOARD 3-5 PT BOARD.
14 MDS-JE770 3-2. UPPER CASE (408226) 1 Two screws (CASE 3TP2) 1 Two screws (CASE 3TP2) 1 Screw (CASE 3TP2) 2 Case (408226) 3-3. FR ONT P ANEL SECTION 4 Three screws (+BVTP3x8) 4 Two screws (+BVTP3x8).
15 MDS-JE770 3-4. MAIN BO ARD 3-5. PT BO ARD , VOL-SEL BO ARD (SP model) 6 Two screws (+BVTP3x8) 4 Three screws (+BVTP3x8) 5 screw (+BVTP3x8 ) 3 Connector (CN400) 2 Wire (flat type) (23core) (CN1) 1 W.
16 MDS-JE770 3-6. MECHANISM DECK SECTION (MDM-7A) 3-7. O VER LIGHT HEAD (HR901), BD BO ARD 2 Two step screws (+BVTTWH M3) 2 Two step screws (+BVTTWH M3) 1 Harnes s 3 Mechanism deck 6 3 Head, over ligh.
17 MDS-JE770 3-8. HOLDER ASSY 3-9. LO ADING MO T OR ASSY (M103) 5 3 6 Holder ASSY 2 Claw 4 Boss 4 Boss 1 Spring (holder), tension 2 Two screws (PWH1.7x2.
18 MDS-JE770 3 A A 1 Two screws (BTP2X6) 9 Two screws (PWH1.7X2.5) 0 Motor ASSY, sle d (M102) 7 Lever (CHG) 2 Guide (L) 6 Slider 8 Lever (head) 4 Slider (EJ) 5 Remove the claw.
19 MDS-JE770 2 Spindle motor ASSY (M101) 1 Three screws (M1.7), tapping 3-12. SPINDLE MO TER ASSY (M101).
20 MDS-JE770 Function name MENU/NO button YES button AMS Left or Right knob Push Function Cancel or move to top hierarchy Set Select Set submenu SECTION 4 TEST MODE 4-1.
21 MDS-JE770 Displa y AUTO CHECK Err Display TEMP ADJUS LDPWR ADJUS Iop Write Iop NV Save EF MO ADJUS EF CD ADJUS FBIAS ADJUS AG Set (MO) AG Set (CD) TEMP CHECK LDPWR CHECK EF MO CHECK EF CD CHECK FBI.
22 MDS-JE770 “ CPLAY1 MID ” t “ CPLAY1 OUT ” t “ CPLAY1 IN ” “ CREC1 MID ” t “ CREC1 OUT ” t “ CREC1 IN ” 4-5-1. Operating the Continuous Pla yback Mode 1. Entering the continuous playback mode 1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.
23 MDS-JE770 Function G x M m REC MODE PLA Y MODE LEVEL/DISPLA Y/CHAR A REPEA T Contents Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking servo turns ON/OFF . Stops continuous playback and continuous recording.
24 MDS-JE770 G X REC SYNC L.SYNC OVER B/1 A-/REP REC MODE DISC/LP2 SLEEP/SHUF MONO Servo OFF T racking servo ON Recording mode OFF CL V normal mode T racking offset cancel OFF Groove Low reflection CL.
25 MDS-JE770 SECTION 5 ELECTRICAL ADJUSTMENTS 5-1. PARTS REPLA CEMENT AND ADJUSTMENT If malfunctions caused by Optical pick-up such as sound skipping are suspected, follow the following check. Chec k before replacement Other faults are suspected. Check the threading mechanism, etc.
26 MDS-JE770 5-6-4. Auto Check (See page 29) Start YES NO NO NO NO NO NO NO NO YES YES YES YES YES YES YES Replace IC195 Replace OP or IO195 Replace IC101, IC195, or D101 5-11.
27 MDS-JE770 5-7. Initial setting of adjustment values 5-8. Recording of Iop information 5-9. TEMP ADJUST 5-10. Laser power adjustment 5-1 1. Iop NV Save 5-12. Traverse adjustment 5-13. Focus bias adjustment 5-16. Auto gain adjustment 5-6-4. AUTO CHECK 5-2.
28 MDS-JE770 5. Press the MENU/NO button and display “LDPWR CHECK” and stop the laser emission. (The MENU/NO button is effective at all times to stop the laser emission.) Note 1: After step 4, each time the YES button is pressed, the display will be switched between “LD 0.
29 MDS-JE770 7. Press the YES button and display “EFB = MO-W”. 8. Observe the waveform of the oscilloscope, and check that the specified value is satisfied. Do not rotate the l AMS L knob. (W rite power traverse checking) (T rav erse W av eform) 1 1.
30 MDS-JE770 5-6-8. C PLA Y Check MO Error Rate Chec k Checking Procedur e : 1. Load a continuously recorded test disc (MDW -74/GA-1). (Refer to “5-5. Using the Continuously Recorded Disc”.) 2. Rotate the l AMS L knob and display “CPLA Y1 MODE”(C34).
31 MDS-JE770 5-7. INITIAL SETTING OF ADJUSTMENT VALUE Note: Mode which sets the adjustment results recorded in the non-vola- tile memory to the initial setting value. However the results of the temperature compensation offset adjustment will not change to the initial setting value.
32 MDS-JE770 7. Then, rotate the l AMS L knob and display “LDPWR CHECK”(C13). 8. Press the YES button once and display “LD 0.9 mW $ ”. Check that the reading of the laser power meter become the speci- fied value. 9. Press the YES button once more and display “LD 7.
33 MDS-JE770 1 1. Rotate the l AMS L knob until the waveform of the oscilloscope moves closer to the specified value. In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.
34 MDS-JE770 5-14. ERROR RA TE CHECK 5-14-1. CD Error Rate Chec k Checking Procedur e : 1. Load a check disc (MD) TDYS-1. 2. Rotate the l AMS L knob and display “CPLA Y1 MODE”(C34). 3. Press the YES button twice and display “CPLA Y1 MID”. 4. The display changes to “C = AD = ”.
35 MDS-JE770 NO TE: It is useful to use the jig. for checking the waveform. (Refer to Servicing Note on page 6.) [BD BO ARD] (SIDE B) D101 IC151 23 1 27 1 1 7 IC101 CN101 CN103 CN102 IC195 IC190 CN105 IC102 * NO TE 5-17.
36 MDS-JE770 SECTION 6 DIA GRAMS 6-1. CIRCUIT BO ARDS LOCA TION KEY -SW board KB board HP board DISPLA Y board BD board MAIN board PT board V OL-SEL board (SP model) • Abbreviation SP : Singapore mo.
37 37 MDS-JE770 THIS NO TE IS COMMON FOR PRINTED WIRING BO ARDS AND SCHEMA TIC DIA GRAMS. (In addition to this, the necessary note is printed in each b lock.) For schematic diagrams. Note: • All capacitors are in µ F unless otherwise noted. pF: µµ F 50 WV or less are not indicated except f or electrolytics and tantalums.
MDS-JE770 38 38 6-2. BLOCK DIA GRAMS – BD SECTION – F C B D A E I J J I B A C D E F DETECTOR J I A B C D E F LD PD LASER DIODE ILCC PD OPTICAL PICK-UP (KMS-260B/260E) AUTOMATIC POWER CONTROL Q121, 122 APC PD APCREF AT AMP B.
MDS-JE770 39 39 – MAIN SECTION – X550 45.1584MHz – 1 – 2 LED DRIVE Q726 ROTARY ENCODER FL DRIVE Q761, 762 D726 STANDBY A/D, D/A CONVERTER IC500 SDTO ADDT DADT, BCK, LRCK SDTI A B LINE AMP IC31.
40 40 MDS-JE770 MAIN BOARD CN1 (Page 45) MAIN BOARD CN2 (Page 45) B A BD BOARD (SIDE B) 1 2 3 4 5 Ref. No . Location D101 A-4 Q101 B-1 Q131 C-1 Q132 B-1 Q133 B-1 Q134 B-1 • Semiconductor Location Ref. No. Location D181 D-3 D183 D-3 IC101 A-3 IC102 B-3 IC141 C-1 IC151 C-2 IC153 C-3 IC171 D-2 • Semiconductor Location Ref .
MDS-JE770 41 41 6-4. SCHEMA TIC DIA GRAM – BD SECTION (1/2) – • See page 37 for Wa veforms. • See page 52 for IC Pin Functions. • See page 50 for IC Block Diagrams.
MDS-JE770 42 42 6-5. SCHEMA TIC DIA GRAM – BD SECTION (2/2) – • See pa g e 37 for W aveforms. • See pa ge 53 for IC Pin Functions. • See page 50 fo r IC Bloc k Diagrams.
MDS-JE770 43 43 6-6. SCHEMA TIC DIA GRAM – MAIN SECTION (1/2) – • See page 37 for W aveforms. • See page 56 f or IC Pin Functions. • See page 51 for IC Block Dia grams.
MDS-JE770 44 44 6-7. SCHEMA TIC DIA GRAM – MAIN SECTION (2/2) – • See page 51 for IC Bloc k Diagrams. R434 R407 C402 C412 C424 C442 R425 R424 C405 C401 C411 C406 C416 C423 C425 C431 C432 L831 Q8.
MDS-JE770 45 45 BD BOARD CN103 (Page 40) B BD BOARD CN102 (Page 40) A DISPLAY BOARD CN700 (Page 46) C HP BOARD CN790 (Page 46) D 11 (11) 1-681-740- MAIN BOARD KB BOARD CN2780 (Page 46) E PT BOARD CN92.
MDS-JE770 46 46 Ref . No. Location D726 F-1 D733 E-4 D775 C-7 IC740 F-3 IC760 A-4 Q726 E-6 Q733 E-5 Q761 A-7 Q762 A-7 Q775 B-2 6-9. PRINTED WIRING BO ARD – DISPLA Y SECTION – • See page 36 for Cir cuit Board Location. There are a fe w cases that the par t isn’t mounted in model is printed on diagram.
MDS-JE770 47 47 6-10. SCHEMA TIC DIA GRAM – DISPLA Y SECTION – R 7 1 4 R 7 1 3 R 7 1 2 R 7 3 2 R 7 0 5 R 7 0 4 R 7 0 3 R 7 0 2 R 7 4 7 R 7 0 6 C 7 9 1 R 7 2 4 R 7 2 3 R 7 2 2 C 7 6 8 C 7 7 0 C 7 6.
MDS-JE770 48 48 6-11. PRINTED WIRING BO ARD – PO WER SECTION – • See page 36 f or Circuit Boar d Location. There are a f ew cases that the part isn’t mounted in model is printed on diagram.
MDS-JE770 49 49 6-12. SCHEMA TIC DIA GRAM – PO WER SECTION – (Page 44) MAIN BOARD (2/2) CN400.
MDS-JE770 50 50 6-13. IC BLOCK DIA GRAMS IC101 CXA2523AR (BD BO ARD) IC151 CXD2662R (BD BO ARD) IC141 BH6519FS-E2 (BD BO ARD) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 123456789 10 11 12 13 14 1.
51 MDS-JE770 IC500 AK4524 (MAIN BO ARD) IC440 M54641L (MAIN BO ARD) VCOM AINR AINL 2 1 3 VREF 4 TEST 7 XTI 9 XT ALE 10 XTO 8 SDTI 14 LRCK 11 BICK 12 SDTO 13 AGND 5 VA 6 A/D CONVERTER BLOCK D/A CONVERT.
52 MDS-JE770 6-14. IC PIN FUNCTION DESCRIPTION • IC101 CXA2523AR RF Amplifier (BD BO ARD) Pin No . Pin Name I/O Description I J VC A to F PD APC APCREF GND TEMPI TEMPR SWDT SCLK XLA T XSTBY F0CNT VR.
53 MDS-JE770 MNT0 (FOK) MNT1 (SHCK) MNT2 (XBUSY) MNT3 (SLOC) SWDT SCLK XLA T SRDT SENS XRST SQSY DQSY RECP XINT TX OSCI OSCO XTSL DIN0 DIN1 DOUT DADTI LRCKI XBCKI ADDT DADT LRCK XBCK FS256 DVDD A03 to.
54 MDS-JE770 Description Pin No . Pin Name I/O 48 49 50, 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 D1 D0 D2, D3 MVCI ASYO ASYI A VDD BIAS.
55 MDS-JE770 Description Pin No . Pin Name I/O 86 87 88 89 90 91 92 93 94 95 96 - 98 99 100 TFDR DVDD FFDR FRDR FS4 SRDR SFDR SPRD SPFD FGIN TEST1 to TEST3 DVSS EFMO O I O O O O O O O I (S) I — O T racking servo drive PWM output (+) +3V power supply (Digital) Focus servo drive PWM output (+) Focus servo drive PWM output (–) 176.
56 MDS-JE770 1 FLDT O Serial data signal output to the display driver . 2 FLCK O Serial clock signal output to the display driver . L: Active 3 A1-IN I A1 Control input. 4 SIRCS I Remote control input. 5 - 7 NC — Not used. 8 BYTE I Data bus changed input.
57 MDS-JE770 40 ADA. LA TCH O Chip select signal output to the AK4524. L: Active 41 EPN I Not used. (Fixed at L) 42 L : DINT1/H : CLIP — Not used. (open) 43 NC — Not used. 44 PROTECT I Recording-protection claw detection input from the protection detection switch.
58 MDS-JE770 81 STB O Strobe signal output to the power supply circuit. H: Power supply ON: L: standby 82 BEEP SW — Not used. 83 REC — Not used. 84 FLCS O Chip select signal output to the MSM9202 (IC760) 85, 86 D.VOL0,1 — Not used. 87, 88 JOG0, JOG1 I Jog dial pulse input from the rotary encoder .
59 MDS-JE770 Description Pin Name Pin No. I/O 1, 2 AD3, AD4 O Fluorescent display tube (FL760) anode electrode drive 3-37 SEG1-35 O Fluorescent display tube (FL760) segment electrode drive 38 VDISP1 I.
60 MDS-JE770 7-1. CHASSIS SECTION Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks SECTION 7 EXPLODED VIEWS NO TE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service.
61 MDS-JE770 7-2. FR ONT P ANEL SECTION Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks supplied with RV790 59 54 54 54 54 63 54 54 60 62 61 64 51 52 54 57 56 54 54 53 55 58 65 supplied with J790 not supplied not supplied FL750 51 X-4953-713-1 P ANEL ASSY , FRONT .
62 MDS-JE770 7-3. MECHANISM SECTION-1 (MDM-7A) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks #2 304 305 306 302 301 307 305 320 302 311 319 312 310 309 314 313 315 316 31.
63 MDS-JE770 7-4. MECHANISM SECTION-2 (MDM-7A) The components identified by mark 0 or dotted line with mark 0 are critical for saf ety . Replace only with par t number specified.
64 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MDS-JE770 SECTION 8 ELECTRICAL P ARTS LIST Ref. No. Part No. Description Remarks Ref.
65 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MDS-JE770 BD IC190 8-759-460-72 IC BA033FP-E2 IC195 8-759-640-41 IC BR24C08F-E2 <JUMPER RESISTOR> JW201 1-216-295-9.
66 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MDS-JE770 DISPLA Y HP KEY-SW A-2007-926-A DISPLA Y BOARD, COMPLETE (AEP ,UK) A-2007-932-A DISPLA Y BOARD, COMPLETE (SP) *********************** * 4-955-901-01 CUSHION (FL) * 4-996-686-01 HOLDER (FL) <CAP ACITOR> C700 1-126-153-11 ELECT 22uF 20% 6.
67 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MDS-JE770 MAIN <CONNECTOR> CN720 1-766-739-11 CONNECTOR, BOARD TO BOARD 8P <DIODE> D726 8-719-046-44 LED SEL5.
68 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MDS-JE770 MAIN C550 1-164-159-11 CERAMIC 0.1uF 50V C551 1-104-665-11 ELECT 100uF 20% 10V C552 1-164-159-11 CERAMIC 0.1uF 50V C553 1-162-195-31 CERAMIC 4.7PF 10% 50V C554 1-162-294-31 CERAMIC 0.
69 MDS-JE770 MAIN Q490 8-729-194-57 TRANSISTOR 2SC945TP-QP Q821 8-729-620-05 TRANSISTOR 2SC2603TP-EF Q822 8-729-620-05 TRANSISTOR 2SC2603TP-EF Q851 8-729-620-05 TRANSISTOR 2SC2603TP-EF Q911 8-729-922-37 TRANSISTOR 2SD2144S-TP-UVW <RESISTOR> R3 1-247-807-31 CARBON 100 5% 1/4W R9 1-249-425-11 CARBON 4.
70 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MDS-JE770 R912 1-249-437-11 CARBON 47K 5% 1/4W R1090 1-249-429-11 CARBON 10K 5% 1/4W (SP) <VIBRA TOR> X15 1-795-004-21 VIBRA TOR, CERAMIC (10MHz) X550 1-781-998-11 VIBRATOR, CR YST AL (45.
71 MDS-JE770 MEMO.
MDS-JE770 REVISION HIST OR Y Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.
デバイスSony MDS-JE770の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sony MDS-JE770をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSony MDS-JE770の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sony MDS-JE770の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sony MDS-JE770で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sony MDS-JE770を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSony MDS-JE770の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sony MDS-JE770に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSony MDS-JE770デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。