Stanley Black & DeckerメーカーIW24の使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL Safety , Operation and Maintenance IW24 HYDRAULIC IMP ACT WRENCH © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66268 8/2014 V er .
2 ► IW24 User Manual.
IW24 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► IW24 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
IW24 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safe- ty . Review them carefully before operating the tool and before performing general maintenance or repairs.
6 ► IW24 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
IW24 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► IW24 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
IW24 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► IW24 User Manual WRENCH T ORQUE INFORMA TION F ACT ORS THA T AFFECT TORQUE An impact wrench is a rotary hammer that impacts the head of a bolt or nut. It does not apply a slow steady torque as a standard torque wrench. Therefore, sever- al factors affect the result of torque when using impact wrenches: 1.
IW24 User Manual ◄ 1 1 COLD WEA THER OPERA TION If the wrench is to be used during cold weather , preheat the hydraulic uid at low engine speed. When using the normally recommended uids, uid temperature should be at or above 50 °F/10 °C (400 ssu/82 centistokes) be- fore use.
12 ► IW24 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
IW24 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diag- nosing faults in operation of the wrench, always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the tool as listed in the following table.
14 ► IW24 User Manual Drive Size .............................................................................................................................. 1-1/2 inch Square Drive Weight ..........................................................
IW24 User Manual ◄ 15 1 2 3 4 5 6 7 8 9 10 11 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 43 47 48 49 52 53 13 45 50 12 12 41 51 10 24 54 55 54 56 57 58 59 44 31 36 6 Clean, apply 242 Loctite™ and torque to 50 ft lb.
16 ► IW24 User Manual IW24 P ARTS LIST Item # P/N Qty Description 1 00016 1 O-RING* 2 00026 1 O-RING* 3 00255 1 O-RING* 4 00580 1 SETSCREW 1/4-20 X 1/4 5 00663 1 RET AINING RING 6 00697 8 LOCKW ASHER 1/2" I.D 7 00717 1 O-RING* 8 00812 4 LOCKW ASHER 3/8" I.
IW24 User Manual ◄ 17 ALL IW24 IMP ACT WRENCH MODELS Notication of change in valve handle assembly and on/off spool. Part numbers and compatibility (March 2013). Beginning at serial number 031513001, the valve handle assembly has changed. The prior style (part # 17279) used a steel spool sleeve installed in the valve handle assembly .
18 ► IW24 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation.
IW24 User Manual ◄ 19 NOTES.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
デバイスStanley Black & Decker IW24の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Stanley Black & Decker IW24をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはStanley Black & Decker IW24の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Stanley Black & Decker IW24の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Stanley Black & Decker IW24で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Stanley Black & Decker IW24を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はStanley Black & Decker IW24の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Stanley Black & Decker IW24に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちStanley Black & Decker IW24デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。