Texas InstrumentsメーカーSCAU020の使用説明書/サービス説明書
ページ先へ移動 of 21
10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board User's Guide March 2007 Serial Link Products SCAU020.
2 SCAU020 – March 2007 Submit Documentation Feedback.
Contents 1 General Description ..................................................................................................... 5 2 Signal Path and Control Circuitry ................................................................................
List of Figures 1 CDCE421EVM Evaluation Board .......................................................................................... 5 2 CDCE421EVM Programming Blocks ................................................................................
1 General Description User's Guide SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board Figure 1. CDCE421EVM Evaluation Board Features: • Easy-to-use evaluation module generates low phase noise clocks between 10.
www.ti.com 2 Signal Path and Control Circuitry Signal Path and Control Circuitry The CDCE421 can accept a 27MHz—38.33MHz frequency input from either an LVCMOS source (up to 3.3V) or a crystal in the same frequency range. The CDCE421EVM is divided into four blocks.
www.ti.com 3 Block Description 3.1 Block A 3.2 Block B 3.3 Block C 3.4 Block D 4 Software-Selectable Options Block Description This section discusses the four EVM blocks. Block A includes a CDCE421 QFN device that accepts an LVCMOS reference input through the vertical SMA input connector (Ref Input) which is ac-coupled onto the board.
www.ti.com 5 Installing the Software GUI and USB Driver Installing the Software GUI and USB Driver The CDCE421EVM software can be installed on a PC running the Microsoft Windows ® 2000 operating system or higher (including Windows XP ® ). To start software installation, run the ChronosSetup.
www.ti.com 6 ChronosGUI 6.1 Using Software-Enabled Automatic PLL Selection ChronosGUI After the setup wizard completes, start the GUI interface from the Start menu (Start → Texas Instruments → Chronos Eval → TIChronosGUI.exe). Connect the USB cable to the EVM.
www.ti.com ChronosGUI frequency should be entered here in this format: xx.xxx (specified in MHz). Step 3. Output Calculator and Apply PLL Settings. The second row of calculations is used to obtain the PLL settings necessary to achieve a particular output frequency provided a given input frequency to CDCE421.
www.ti.com 6.2 Manual PLL Block Selection (Advanced Control) ChronosGUI The advanced control screen helps to set the PLL without having to manually alter the individual blocks within the PLL.
www.ti.com ChronosGUI Table 1 lists the various menu items in this screen. Table 1. Software Settings Description Section Function VCO Select Selects between VCO1 and VCO2. Only one VCO can be used during operation. See CDCE421 data sheet for VCO tuning ranges.
www.ti.com 7 Configuring the Board 7.1 Programming and Testing Configuration (USB Cable Attached)—Default Configuration 7.2 Programming Configuration (USB Cable Attached) AUX Usingexternal 3.
www.ti.com 8 Schematics and Layout Schematics and Layout Figure 9. CDCE421EVM Block Switch Off Figure 10 through Figure 14 show the printed circuit board (PCB) schematics. Note: Board layouts are not to scale. These figures are intended to show how the board is laid out; they are not intended to be used for manufacturing CDCE421EVM PCBs.
www.ti.com Schematics and Layout Figure 10. CDCE421EVM Board Schematic SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board 15 Submit Documentation Feedback.
www.ti.com Schematics and Layout Figure 11. CDCE421EVM Board—Block A Schematic 16 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board SCAU020 – March 2007 Submit Documentation Feedback.
www.ti.com Schematics and Layout Figure 12. CDCE421EVM Board—Block B Schematic SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board 17 Submit Documentation Feedback.
www.ti.com Schematics and Layout Figure 13. CDCE421EVM Board—Block C Schematic 18 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board SCAU020 – March 2007 Submit Documentation Feedback.
www.ti.com Schematics and Layout Figure 14. CDCE421EVM Board—Block D Schematic SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board 19 Submit Documentation Feedback.
EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
デバイスTexas Instruments SCAU020の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Texas Instruments SCAU020をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTexas Instruments SCAU020の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Texas Instruments SCAU020の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Texas Instruments SCAU020で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Texas Instruments SCAU020を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTexas Instruments SCAU020の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Texas Instruments SCAU020に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTexas Instruments SCAU020デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
