Texas InstrumentsメーカーSLUU083Aの使用説明書/サービス説明書
ページ先へ移動 of 19
.
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
T rademarks iii Read This First Preface Read This First About This Manual This user ’ s guide describes the bq2400x evaluation module. The EVM conve- niently evaluates a linear Li-ion bq2400x charge-management solution for one- and two-cell battery-pack applications.
Running Title — Attribute Reference v Contents Contents 1 Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Background 1-2 . . . . . . . . .
1-1 Introduction This user ’ s guide describes the bq2400x Evaluation Module (SLUP051). The EVM conveniently evaluates a linear Li-ion bq2400x charge-management solution for one- and two-cell battery-pack applications. This guide describes a complete designed-and-tested charger , which delivers up to 1.
Background 1-2 1.1 Background The bq2400x series ICs are advanced Li-Ion linear charge management devices for highly integrated and space-limited applications.
Performance Specification Summary 1-3 Introduction T able 1 – 2. Performance Specification Summary (T wo Cell) Specification T est Conditions Min Ty p Max Units Input dc voltage, V DC 9.1 9.5 † V Battery charge current I CHG J4 shorted, J3 open 0.
2-1 T est Summary T est Summary This chapter shows the test setups used, and the tests performed, in designing the bq2400xEVM. T opic Page 2.1 Setup 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup 2-2 2.1 Setup The bq2400X EVM board requires a DC power source to provide input power and a single-cell lithium-ion or lithium-polymer battery to charge. Note: Other versions of the bq2400x IC can charge two-cell battery packs. The test setup connections and jumper setting selections are listed below .
T est Procedures 2-3 T est Summary Note: V I for a single cell should not exceed 5.3 VDC for the 1-A charge rate and 7.6 V for the .5-A charge rate. Adjust the input power supply for 5 V . The red LED should illuminate to indicate charging, unless there is a fault or the battery is fully charged.
T est Procedures 2-4 The bq2400x enters preconditioning mode if the battery is below the LowV threshold. In this mode, the bq2400x trickle-charges with approximately 65 mA for approximately 23 minutes. If the battery does not reach the LowV threshold after this period, then the charge current is terminated and the bq2400x enters fault mode.
3-1 Physical Layouts Physical Layouts This chapter contains the board layout and assembly drawings for the SLUP051 EVM. T opic Page 3.1 Board Layout 3-2 .
Board Layout 3-2 3.1 Board Layout Figure 3-1 shows the top layer of the SLUP051. Figure 3-2 shows the bottom layer . Figure 3-3 shows the SLUP051 top assembly view .
Board Layout 3-3 Physical Layouts Figure 3 – 2. SLUP051 Board Layout Bottom Layer Figure 3 – 3. SLUP051 T op Assembly View.
4-1 Bill of Materials Bill of Materials This chapter contains the bill of materials required for the SLUP051 EVM. It also specifies the charge status configurations for the bq2400x. T opic Page 4.1 Bill of Materials 4-2 . . . . . . . . . . . . . . . .
Bill of Materials 4-2 4.1 Bill of Materials T able 4-1 lists materials required for the SLUP051 EVM. T able 4 – 1. SLUP051 Bill of Materials Qty Reference Designator Part Number Description MFG Size 2 C1, C4 T AJC106M016R Capacitor , 10 µ F tantalum, 16 V , ± 20%, 6032 A VX-Future 1210 1 C2 C0805X7R250-104KNE Capacitor , 0.
bq2400x Charge Status Configurations 4-3 Bill of Materials 4.2 bq2400x Charge Status Configurations T able 4 – 2 lists the charge status configurations for the bq2400x.
A-1 Schematic Schematic This chapter contains the schematic diagram for the EVM. T opic Page A.1 Schematic A-2 . . . . . . . . . . . . . . . . . . . . .
J3 1 3 4 2 5% 511 R6 BQ24000 U1 26 27 28 29 30 25 24 23 22 21 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 0.2 R4 5% 511 R8 1% 51.1K R1 1% 316K R2 0.1 R3 16V 10UF C4 1% 95.3K R7 J4 1 3 4 2 0.1UF C2 J10 1 2 1% 18.7K R5 100 R9 10UF C1 D2 D1 J1 J7 3 2 1 J2 3 2 1 J6 3 2 1 J5 3 2 1 J8 2 1 J9 0.
デバイスTexas Instruments SLUU083Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Texas Instruments SLUU083Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTexas Instruments SLUU083Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Texas Instruments SLUU083Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Texas Instruments SLUU083Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Texas Instruments SLUU083Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTexas Instruments SLUU083Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Texas Instruments SLUU083Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTexas Instruments SLUU083Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
