THOMSONメーカーASR08Tの使用説明書/サービス説明書
ページ先へ移動 of 16
2 T o take maximum advantage of all the features of your satellite receiver , please read this user manual very carefully . ASR 08 T SA TELLITE RECEIVER The package contains the following items : • .
3 ENGLISH Impor tant safety and operating information. This set was designed and manufactured in accordance with international safety standards. Y ou must nonetheless obser ve certain rules to guarantee optimum results and safety . Read this user manual before attempting to put the set into ser vice.
4 ENGLISH CONTENTS Page REMOTE CONTROL UNIT .................................................................................... 5 FRONT P ANEL KEYP AD ....................................................................................... 6 REAR P ANEL CONNECTIONS .
5 ENGLISH REMOTE CONTROL UNIT ST ANDBY key (Switch set on using the CH M /CH N keys, or 0 to 9) Parental lock. Numeric keypad : - Channel selection - Frequency entr y - T oturn on the receiver . Channel scrolling (zapping) and to turn on the receiver .
6 ENGLISH TV DECODER VCR L R IF INPUT MADE IN GERMANY A B W ARNING! Shock Hazard Do not open j Mains socket to connect the set to the ac power supply .
7 ENGLISH A correctly installed satellite antenna is essential for the receiver to operate. The satellite antenna coaxial cable must be long enough to reach the desired receiver site. Install the receiver near your television set, making sure to leave ventilation space of about 15 cm to the sides and above the receiver .
8 ENGLISH INST ALLA TION OF SA TELLITE RECEIVER - Connect the LNB coaxial cable to Socket d IF INPUT A. - Y ou can, if applicable, connect a second LNB to IF INPUT B connector e . Plug F must be tightened by hand on the threading of the plug. Do not use any tools.
9 ENGLISH On/Standby Using set keypad: Press the On/Standby key . Using remote control: Switch the receiver on by pressing one of the numeric keys (0 to 9), or on the remote control keypad. If the set is switched on using the or keys, the last programme number active before switching of f is called up, for example : " 13".
10 ENGLISH RECORDING SA TELLITE PROGRAMMES If your receiver is connected to a VCR, you can record satellite programmes. Paragraph 2 : Connection to a VCR in the INST ALLA TION OF SA TELLITE RECEIVER chapter of the present manual describes the procedure for connecting the VCR to the receiver .
11 ENGLISH Y our receiver is already programmed to receive the most important satellite signals. Y ou can, however , change the programming or add new channels at any time. T o store a new channel in memor y , you need the following information (found in specialist satellite TV magazines): 1.
12 ENGLISH PROGRAMMING A NEW CHANNEL 4. Audio mode selection Press the key to display the audio mode, e.g. : "T on1". Press several times to display all the available modes.
13 ENGLISH 1. V ideo Level This feature lets you adjust the video level to compensate for differences in level that may exist between the various satellites. Press the key to display the current mode, e.g. : " HI ". Press the key again to select the second mode.
14 ENGLISH 4. 22 kHz Switching Signal This signal can be used to control either a switching box or , for example, the LNB (high band/low band). Press the key briefly to display the current mode, e.g. : "22-". Press again to select the second mode.
15 ENGLISH CONVENIENCE FEA TURES 1. Parental Lock Used to restrict use of the set, or access to certain programmes. 1. Locking certain programmes. The programme can be selected, but the picture does not appear on screen. The programming cannot be altered.
16 ENGLISH TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE Display inoperative - Mains lead incorrectly connected - Power cut Unable to switch set on - Shor t circuit in the coaxial cable connected to the LNB No picture - SCAR T cable incorrectly connected. - Wrong LNB selection.
17 ENGLISH RF P ART - INPUT FREQUENCY : 900-2150 MHz (IN STEPS OF 1 MHz) - INPUT IMPEDANCE : 75 OHM - INPUT LEVEL : -60 dBm -30 dBm - INTERMEDIA TE FREQUENCY : 479.
デバイスTHOMSON ASR08Tの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
THOMSON ASR08Tをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTHOMSON ASR08Tの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。THOMSON ASR08Tの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。THOMSON ASR08Tで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
THOMSON ASR08Tを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTHOMSON ASR08Tの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、THOMSON ASR08Tに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTHOMSON ASR08Tデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。