Trekメーカー9iの使用説明書/サービス説明書
ページ先へ移動 of 27
C L K T M E A V G M A X T R P A V G M P H F This manual explains the installa- tion and use of the Trek Incite 9i and 11i bicycle computer .
Safety and general guidelines .................................................. 1 F unctions .................................................................................. 2 Installation ..........................
While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the road, you could hit an obstacle, which may cause you to lose control and fall.
.
.
T ools needed: • Electrical tape • Slot-type screwdriver • Phillips-type screwdriver • Scissors Stem mount Hand.
The Trek Incite 9i or 11i computer can be mounted on the handlebar or on the stem (Figure 3). 1.
Check that the computer base cannot be rotated around the handlebar , and that the computer cannot slide backwards on the computer base (Figure 5). 1.
The wheel magnet must be aligned so that it passes across the sensor . As the magnet passes the sensor , it must be no further from the sensor than 1 to 3mm (1/32 to 1/8 inch).
The computer wire is usually longer than needed. Extra wire length can be diverted by wrapping it around the brake housing prior to routing it down the fork blade or down tube (Figure 8).
The magnet must pass across the line on the sensor (Figure 9). These instructions are written for the front wheel, but apply equally to installing the magnet and cadence sensor which go on the lef t crank and the frame’s chainstay (Figure 10).
and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is r eading the magnet. If the computer is not displaying a value, realign the sensor and magnet until one is displayed.
Y ou can program the starting values of your computer in a single, easy procedure: • Units • Clock • Wheelsize • Odometer The .
CL K TME A VG MA X TRP A VG MPH F .
CLK TME AVG MAX TRP ODO MH Mode Set 3. Cycle Mode MH and KMH inter change on the screen. 4. Push Set• to select. The temperature icon display . 5. Cycle Mode to C or F 6. Push Set• to select. The computer returns to the start scr een. 1.
CLK TME AVG MAX TRP ODO MH Mode Set Both the 9i and 1 1i allow you to use two differ ent wheel sizes. The icon for Wheel 1 is a small cir cle. The icon for Wheel 2 is a partial circle surr ounding the Wheel 1 icon (Figure 14).
CLK TME AVG MAX TRP ODO MH Mode Set 1. Cycle Mode to TRP 2. Hold the lef t Mode and the right Mode together . The Wheel Select icon changes (Figure 14). Repeat step 2 to change again.
CLK TME AVG MAX TRP ODO MH Mode Set 1. Cycle Mode to CLK (Figure 15). 2. Hold Set• “12” or “24” flashes. CL K TM E AV G MAX TR P A VG MPH F 3.
CLK TME AVG MAX TRP ODO MH Mode Set Y our computer stores data for two intervals- since last ReSet and since last R eStart. R eSet sets ALL data to zero.
CLK TME AVG MAX TRP ODO MH Mode Set Once the computer is programmed and installed, it is very easy to use.
The Incite 9i computer is designed to be easy to install and maintain. However , computers occasionally have problems.
If the computer is giving erratic information, the computer or hear rate strap battery may be running low on power (normally accompanied by the low battery icon, Figure 16). R eplace the batteries whenever the computer malfunctions, or every 6 months.
4. Lif t the battery cover , exposing the battery . Be careful to avoid losing the rubber O-ring seal. 5. R emove the old battery . It may be possible to shake the battery out. Otherwise, carefully pry the battery up with a thin tool or knife blade.
CLK TME AVG MAX TRP ODO MH Mode Set The procedure is almost the same as the basic setup on pages 13-14, except instead of picking a wheel size from the menu, you can program in a 4-digit number .
CLK TME AVG MAX TRP ODO MH Mode Set 4. Push Mode to select. Wheel size appears. Note : If you want to set a cus tom wheel size, go to pa ge 24 now . 5. Cycle Mode through the wheel sizes tro the 4-digit number . 6. Push Set• The left-hand digit flashes.
.
Tr ek Bi cyc le Co rpo ra ti on war ra nt s ea ch new In ci te c om pu ter ag ai ns t de fe ct s in wo rk man sh ip and ma te ria ls .
デバイスTrek 9iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Trek 9iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTrek 9iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Trek 9iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Trek 9iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Trek 9iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTrek 9iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Trek 9iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTrek 9iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
