Tripp LiteメーカーAudio/Video On-Line UPS Systemの使用説明書/サービス説明書
ページ先へ移動 of 16
Owner’ s Man ual 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 • www .tripplite.com Impor tant Safety Instructions 2 Installation 3 Basic Operation 7 Battery Replaceme.
UPS Location W arnings • Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust or direct sunlight. • For best performance, keep the indoor temperature between 32º F and 104º F (0º C and 40º C). • Leave adequate space around all sides of the UPS for proper ventilation.
Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for 2- post mounting). The user must determine the fitness of hardware and procedures before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or rack enclosure.
4 Installation (continued) 2-P ost Mounting If you mount the UPS in a 2-post rack, it requires the addition of a T ripp Lite 2-Post Rackmount Installation Kit (model: 2POSTKITRMWM, sold separately). See Installation Kit owner ’ s manual for installation procedure for 2U UPS models.
5 Impor tant Safety Instructions Connection and Start-Up Plug your UPS’ s line cord into an electrical outlet. Y our UPS must be connected to a dedicated circuit of sufficient amperage. Note, however , that the select models may be fitted with different plug types.
6 Optional Connections (continued) USB and RS-232 Serial Communications Use the included USB cable (see ) and/or DB9 serial cable (see ) to connect the UPS to a Media Center PC, home automation system or server . Install the T ripp Lite PowerAlert Software appropriate to your equipment's operating system.
7 Front P anel Switches “ON/TEST” Button: This switch controls four separate UPS functions: UPS Power ON T o turn the UPS on, press this button, hold it for several seconds until you hear a beep, then release it. The “ON LINE” LED will illuminate.
8 Front P anel Indicator Lights continued “BYP ASS” LED: This yellow light will flash to indicate that the UPS’ s DC/AC inverter is deactivated and the UPS is in the “Bypass” mode.
9 Rear Panel “REPLACE BA TT” LED: This red light will illuminate constantly an d the UPS alarm will beep every 2 seconds if your UPS’ s microprocessor detects a battery fault or if your UPS fails the automatic self-test (after you turn your UPS ON) and the UPS battery is less than fully charged.
Rear Panel continued Input Cord: This permanently attached power cord connects your UPS to a power outlet. AC Receptacles (V aried by Model): These 15-, 20- and 30-amp receptacles provide your connected equipment with pure sine-wave AC output from the AC line during normal operation and from battery power during blackouts and severe brownouts.
11 The UPS’ s control panel lights will turn on in the sequences below to signal that the UPS is having operational difficulties. Lights (On/Flashing) and Condition Solution On: REPLA CE B A TT Let .
12 T roub leshooting (continued) Lights (On/Flashing) and Condition Solution On: BYP ASS, LINE Check the UPS to be sure that there is Flashing: F AUL T adequate space f or air to circulate near Condition: On Bypass due to High the vents and that the f an is working Internal T emperature properly .
13 Battery Replacement Under normal conditions, the original batteries in your UPS will last many years. See Safety section before replacing batteries.
Visit www .tripplite.com/warranty today to register the warranty for your new T ripp Lite product. Y ou'll be automatically entered into a drawing for a chance to win a FREE T ripp Lite product!* * No purchase necessary . Void where prohibited. Some restrictions apply .
15 200507084 93-2474 SMARTONLINE HT OM.qxd 10/20/2005 11:11 AM Page 15.
1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 • www .tripplite.com 200507084 93-2474 200507084 93-2474 SMARTONLINE HT OM.
デバイスTripp Lite Audio/Video On-Line UPS Systemの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Tripp Lite Audio/Video On-Line UPS Systemをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTripp Lite Audio/Video On-Line UPS Systemの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tripp Lite Audio/Video On-Line UPS Systemの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tripp Lite Audio/Video On-Line UPS Systemで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tripp Lite Audio/Video On-Line UPS Systemを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTripp Lite Audio/Video On-Line UPS Systemの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tripp Lite Audio/Video On-Line UPS Systemに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTripp Lite Audio/Video On-Line UPS Systemデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
