Tyan ComputerメーカーS5350の使用説明書/サービス説明書
ページ先へ移動 of 88
Tiger i7320 S5350 User’s Manual i http://www.tyan.com Tiger i7320 /// S5350 Revision 1.00 Copyright © TYAN Computer Corporation, 2004. All rights reserved. No part of this manual may be reproduced or translated without prior writt en consent from TYAN Computer Corp.
Tiger i7320 S5350 Table of Contents ii http://www.tyan.com Table of Contents Before you begin… .............................................................................................................. .... v Chapter 1: Introduction.............
Tiger i7320 S5350 Table of Contents iii http://www.tyan.com 3.5 Security ................................................................................................................... .3 - 2 0 3.6 Power ...........................................
Tiger i7320 S5350 Table of Contents iv http://www.tyan.com Chapter 5: Diagnostics ......................................................................................................... 5-1 5.1 Beep Codes ............................................
Tiger i7320 S5350 B efore you begin… v http://www.tyan.com Before you begin… Check the package contents before you procee d. The retail motherboard package should contain the following: 1 x Tiger .
Tiger i7320 S5350 Chapter 1: Intr oduction 1-1 http://www.tyan.com Chapter 1: Introduction 1.1 Congratulations! Congratulations on your purchase of the power ful Dual Intel Xe on processor solution, the Tiger i7320 S5350. Based on Intel E7320 chipset, the S5350 offers exceptional performance.
Tiger i7320 S5350 Chapter 1: Intr oduction 1-2 http://www.tyan.com • Temperature and voltage monitoring Memory • Dual memory channels, 8 x DIMM sockets • Supports up to eight DDR-266/333 DIMM .
Tiger i7320 S5350 Chap ter 2: Board Installation 2-1 http://www.tyan.com Chapter 2: Board Installation 2.1 Installing the Motherboard The Tiger i7320 S5350 motherboard conforms fully to the ATX specification. Before continuing with the installation, confirm that your chassis supports a standard ATX mothe rboard.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-2 http://www.tyan.com 2.2 Board Image The following is an image of the Tiger i7320 S5350 motherboard. The above photograph is purely representativ e. Due to engineering updates and new board revisions, certain components may change and or be repositioned.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-3 http://www.tyan.com 2.3 Block Diagram The following is a block diagram of the Tiger i7320 S5350..
Tiger i7320 S5350 Chap ter 2: Board Installation 2-4 http://www.tyan.com 2.4 Motherboard Components The diagram below shows the main motherboard components.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-5 http://www.tyan.com 2.5 Jumpers and Connectors The following section gives details of the motherboard pin headers and jumpers and their functions. Pin headers are on-boa rd connectors that can be us ed to connect the motherboard to peripherals.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-6 http://www.tyan.com 2.5.2 SO-DIMM Socket: J19 (Optional) S5350 1 J4 USB1 J3 (CO M1) J2 (VGA) CPUF AN1 PW1 LAN1 BIOS Inte l 6300ES B SA TA1 SA TA2 F.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-7 http://www.tyan.com 2.5.4 Front Panel Connector: J 22 2 1 18 17 PWR_LED- PWR_LED- POWER BUTTON GND LED+ (reserved) LED- (reserved) NC GND INTRU# 2 .
Tiger i7320 S5350 Chap ter 2: Board Installation 2-8 http://www.tyan.com 2.5.6 Chassis Fan Connectors with Fan Contro l: FAN 1/2/3/4/5 +12V Speed Co nt ro l Ta c h o m e t e r S5350 1 J4 USB1 J3 (COM .
Tiger i7320 S5350 Chap ter 2: Board Installation 2-9 http://www.tyan.com 2.5.8 CPU FAN1/FAN2 Connectors +12V Speed Control T a c hom et er +12 V Sp eed Co nt ro l Ta c h o m e t e r S5350 1 J4 USB1 J3.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-10 http://www.tyan.com 2.5.10 Chassis Fan Connectors : FAN6, FAN7 +1 2V GND NC S5350 1 J4 USB1 J3 (COM 1) J2 (VGA) CPUF AN1 PW1 LAN1 BIOS Inte l 6300.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-11 http://www.tyan.com 2.5.12 LAN1/LAN2 acti vity LED Headers: JP21, JP30 JP21 1 S5350 1 J4 USB1 J3 (CO M1) J2 (VGA) CPUF AN1 PW1 LAN1 BIOS Inte l 63.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-12 http://www.tyan.com 2.5.14 Clear CMOS Jumper : JP 25 3 1 Pin 1-2: Normal (Default) 3 1 Pin 2-3: Clear BIOS S5350 1 J4 USB1 J3 (COM 1) J2 (VGA) CPU.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-13 http://www.tyan.com 2.6 Mounting the Motherboard Before installing your motherboard, ensur e that your chassis is fully compatible. The Tiger i7320 S5350 motherboard conforms fully to the ATX specification.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-14 http://www.tyan.com 2.6.1 Installing Memor y Before installing memory, ensure that the memory you have is compatible w i th the motherboard and processor. DDR 266/333 modules are required. Check the TYAN Web site at: www.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-15 http://www.tyan.com 2.6.2 Memory Installation Proce dure Follow these instructions to install memory modules into the Tiger i915 S5350. 1. Press the locking levers in the direction shown in the follow ing illustration.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-16 http://www.tyan.com 1. Locate the processor sockets on the mother board and lift the locking lever as shown. 2. Insert the processor into the socket making sure that pin 1 is correctly located. 3. Return the locking lever to its locked position.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-17 http://www.tyan.com 2.7 Installing Drive Cables IDE and FDD connectors are “keyed” to only allow insertion only one way. TYAN motherboards have two on-board IDE channel s, each supporting two drives.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-18 http://www.tyan.com 2.8 Installing Expansion Cards Before installing add-in cards, you should ensure that they are fully compatible with your motherboard. For this reason, we’ve provi ded the diagrams below, showing the expansion slots that appear on your motherboard.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-19 http://www.tyan.com 2.9 Installing Optional SO-DIMM modules Your Tiger i7320 (S5350) mot herboard may be equipped with an optional proprietary SO- DIMM connector. The SO-DIMM connector can be us ed for expansion cards to provide such features as, additional SATA or SCSI support.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-20 http://www.tyan.com 2.10 Connecting External Devices Your new motherboard supports a number of diffe rent interfaces for connecting peripherals. See the diagram below. Port definitions: A PS2 mouse port (green) B PS2 key board port (purple) C USB 2.
Tiger i7320 S5350 Chap ter 2: Board Installation 2-21 http://www.tyan.com 2.11 Installing the Power Supply There are two power connectors on y our Tige r i7320 S5350. The Tiger i7320 S5350 requires that you have an EPS12V power supply that ha s a 24-pin and an 8-pin power connector.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-1 http://www.tyan.com Chapter 3: BIOS Setup 3.1 About the BIOS The BIOS is the basic input/output system, the firmware on the motherboar d that enables your hardware to interface with your software. This chapter describes different settings for the BIOS that can be used to configure your system.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-2 http://www.tyan.com system manufacturer has carefully chosen the chipset defaults for best performance and reliability. Even a seemingly small change to the Chipset setup options may cause the system to become unstable or unusable.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-3 http://www.tyan.com Boot Use this menu to configure boot options for your system. Exit This contains the vari ous BIOS exit options. 3.3 Main In this section, you can alter general features such as the date and time, as well as access to the IDE configuration options.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-4 http://www.tyan.com 3.3.1 IDE Master / Slave Setup Computer detects IDE drive type from drive C to drive F. Press Enter on any of the Master/Slave options to view advanced details of the corresponding drive.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-5 http://www.tyan.com drives are no longer specified in terms of classi cal geometry, but rather in terms of their total number of user data sectors and addressed using LBA. Disabled / Enabled 32 Bit I/O Enables or disables 32 bit data transfer mode.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-6 http://www.tyan.com 3.3.2 Memory Cache This setting allows you to tweak the various cache settings for optimal performance of your system. Press Enter to display the various cache settings. Cache System BIOS Area This feature is only available when the system BIOS is shadowed.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-7 http://www.tyan.com 3.3.3 Boot Features This option allows setting boot parameters. Press Enter to view the Boot Features screen. Summary Screen Enables or disables the display of the summary screen during boot up.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-8 http://www.tyan.com Extended Memory Testi ng Determines the tests that will be run on e xtended memory (memory above 1MB) during boot up. Normal / Just zero it / None 3.4 Advanced This section facilitates configuring advanced BIOS options for your system.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-9 http://www.tyan.com Large Disk Access Mode This option determines whether a hard drive with more than 1024 c ylinders, more than 16 heads and or more than 64 tracks per sector is present on the s ystem. Set this option to DOS if such a hard drive is present.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-10 http://www.tyan.com 3.4.1 Hardware Monitor This displays critical syst em parameters like CPU speed, fan speeds, voltage levels and CPU temperature. 3.4.2 Advanced Chipset Control This section allows you to fine tune the chipset configuration.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-11 http://www.tyan.com Force Compliance Mode Entry: Enable or Disable PCI-E Compliance mode by setting item to the desired value. Enabled / Disabled DRAM Data Integrit y Mode If you have ECC memory modules installed, select the correct ECC mode with this setting.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-12 http://www.tyan.com 3.4.2.2 Integrated LAN 1 PCI-E port A Device 2: Force PCI Express v1.0 Compatib ility Mode this PCI-E Port A by setting item to the desired value. Aut o / Disabled / Enabled / Force PCI Express v1.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-13 http://www.tyan.com Option ROM Scan Initialize device expansion ROM Enabled / Disabled 3.4.3 Advanced Processor Options This section allows you to fine-tune the processor options. Hyper Th reading T echnology Enable this only if you have an Intel Hyper Threading processor.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-14 http://www.tyan.com thermal monitor’s control circuit, when ac tive, lowers the CPU temperature by throttling the internal CPU clock speed. Th is is done with a 50% duty-c ycle, which means that a 2GHz CPU will then effectivel y run at a 1GHz clock speed.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-15 http://www.tyan.com Serial Port B: This defines how the second serial port is detected and configured. Disabled / Enabled Base I/O Address: Set the base I/O address for serial port A. 3F8 / 2F8 / 3E8 / 2E8 Interrupt: Set the interrupt for serial port A.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-16 http://www.tyan.com Base I/O Address / Interrup t: This determines the base address and interrupt of the parallel port. Disabled / 378/IRQ7 / 278/IRQ5 / 3BC/IRQ7 DMA Channel This BIOS feature determines which DMA channe l the parallel port should use when it is in ECP mode.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-17 http://www.tyan.com 3.4.5 DMA Event Loggi ng Event Logging Select Enabled to allow logging of DMI events Disabled / Enabled ECC Event Lo gging Select Enab.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-18 http://www.tyan.com 3.4.6 Console Redirecti on Com Port Address If enabled it will use a port on the motherboard. Disabled / On-board COM A / On-board COM B / NULL Baud Rate Enables the specified baud rate.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-19 http://www.tyan.com 3.4.7 ASF Configuration Minimum WatchDog Timeout Time for BIOS to stop the WatchDog timer after a r eset has occurred. BIOS Boot Timeout Time for BIOS to boot before the system is reset.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-20 http://www.tyan.com 3.5 Security These settings allow you to configure the security options for your system. The system displays the current supervisor and user passwords. Set Supervisor Password This option allows the supervisor to set the supervisor password to restrict access to the BIOS settings.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-21 http://www.tyan.com 3.6 Power These settings allow you to configure the power options for your system. Resume On Time When enabled, this allows the system to be woken up at a specified time. This time is specified by the Resume Time parameter.
Tiger i7320 S5350 Ch apter 3: BIOS Setup 3-22 http://www.tyan.com 3.7 Boot Use this screen to select options for the Boot Settings Configuration. 3.8 Exit These settings set the exit options on your system. Exit Saving Changes This exits BIOS setup after saving the changes made.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-1 http://www.tyan.com Chapter 4: SATA/RAID Setup 4.1 Introduction This section describes the SATA/RAID function of your Tiger i7320 and how to configure your system. This section also covers Intel Applic ation Accelerator RAID Edition software and its configuration.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-2 http://www.tyan.com 4.2.3 RAID migration feature Intel® Application Accelerator RAID Edition features is an advanced software.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-3 http://www.tyan.com 4.5.1 Creating, Deleting, a nd Resetting R AID Sets Note Please refer to Section 4.7 for illustration examples of the Intel RAID Optio n ROM wi ndows. The Serial ATA RAID set must be configured in the RAID Configuration utility.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-4 http://www.tyan.com 4.5.4 Reset RAID Data Note Please refer to Section 4.7 for illustration examples of the Intel RAID Optio n ROM wi ndows. Warning All data on the RAID drives and any internal RAID structures will be lost.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-5 http://www.tyan.com 4.6.2 Installation Using F 6 Method When you start the installation of Windows* XP, you most likely will be presented with a message stating, ‘Setup could not determine t he type of one or more mass storage devices installed in your sy stem’.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-6 http://www.tyan.com 4.7.3 Using the Intel R AID Option ROM Creating, Deleting, a nd R esetting R AID Volumes The Serial ATA RAID volume may be configured using the RAID Confi guration utility stor ed within the Intel RAID Option ROM.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-7 http://www.tyan.com 1. Select option 1 ‘Create RAID Volume’ and press the <Enter> key and the following window will appear: Enter a st ring be tween 1 and 16 charac ters in length that can be u sed to uniq uely identify the RAID volume.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-8 http://www.tyan.com Pres s "ENTER" to C rea te the specif ie d volume . Inte l (R) RAID for Serial AT A - RAID Configu ration Utility Copyr ight (C) 2003-04 Intel Corpor ation .
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-9 http://www.tyan.com RAID V olumes : ID Na m e Le v e l S t r ip Siz e St at u s Bo ot a b le 0 R AI D _Vo l um e1 RAI D 0 ( S tr i p e ) N / A 23 2 .
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-10 http://www.tyan.com Delete RAID Volume Warning By performing this operation, all data on the RAID drives will be lost. 1. Select option 2 ‘Delete RAID Volume’ fr om the main menu window and press the <Enter> key to select a RAID volume for deletion.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-11 http://www.tyan.com Delet ing a vo lume will dest roy the vo lume data on the drive (s) and ca u s e any memb er disk s to beco m e av ai l abl e as non-R AI D disk s .
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-12 http://www.tyan.com 4.8 Installing the Intel Application Accelerator RAID Edition 4.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-13 http://www.tyan.com Installation: Welcome Screen Click on the ‘Next’ button after the following welcome window appears: I.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-14 http://www.tyan.com Installation: Select Program F older Select a program folder in the following windo w where you would lik.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-15 http://www.tyan.com Installation: InstallShield(R ) Wizard Complete Once installation is complete, the following window will appear: 4.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-16 http://www.tyan.com To confirm that the Intel Application Accelerator RAID Edition has been installed, complete the following.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-17 http://www.tyan.com • Then look for a parameter in the Parameters list box titled ‘Driver Version’. This should have a version number in the following format: 3.6.0.xxxx 4.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-18 http://www.tyan.com 4.12.2 “RAID Ready” System Require ments In order for a system to be considered “RAID Ready”, it must meet all of the following requirements: 1.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-19 http://www.tyan.com 1. Create a new partition using Windows Disk Management or 2.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-20 http://www.tyan.com Note The ‘Physical Disks’ listed in your system can differ from the following illustration.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-21 http://www.tyan.com Note Note: Creating a RAID volume from an existing disk can also be accomplished by clicking on the ‘Actions’ file menu, and then arrow down and click on 'Create RAID Volume from Existing Hard Driver'.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-22 http://www.tyan.com 4KB For specialized usage models requiring 4KB strips 8KB For specialized usage models requiring 8KB stri.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-23 http://www.tyan.com 4.13.2 Migration Process Ma y Take Considerable Time to Co mplete The migration process may take up to two hours to complete depending on the size of the disks being used and the strip size selected.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-24 http://www.tyan.com Note The time remaining for your syste m can differ from the following example. If the migration process was completed successfu lly, you will need to r eboot your system to use the entire volume capacity.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-25 http://www.tyan.com 2. Depending on your system configuration, complete one of the following set of tasks: If System has Intel RAID Option ROM Installed: a.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-26 http://www.tyan.com 4.16.2 Create Volume Manuall y The Intel Application Accelerator RAID Edition of fers the ability to create a RAID volume.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-27 http://www.tyan.com RAID Volum e Name: A desired RAID volume name needs to be t yped in where the ‘RAID_Volume1’ text currentl y appears above. The RAID volume name has a maximum limit of 16 characters.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-28 http://www.tyan.com Confirm Creation of New RAID Volume Confirm the creation of the new RAID volume and then click ‘Next’: 4.
Tiger i7320 S5350 Chapter 4: SATA/RAID Setup (for S ATA R AID m odel) 4-29 http://www.tyan.com.
Tiger i7320 S5350 Ch apter 5: Diagnostics 5-1 http://www.tyan.com Chapter 5: Diagnostics Note: if you experience problems with setting up your system, always check the following things in the following order: Memory, Video, CPU By checking these items, you will most li kely find out what the problem might have b een when setting up your system.
Tiger i7320 S5350 Appendix I: Glossar y 6-1 http://www.tyan.com Appendix I: Glossary ACPI (Advanced Configurati on and Power Interface): a power management specification that allows the operating system to control the amount of power distributed to the computer’s devices.
Tiger i7320 S5350 Appendix I: Glossar y 6-2 http://www.tyan.com Cache size : refers to the physical size of the ca che onboard. This should not be confused with the cacheable area, which is the total amount of memory which can be scanned b y the s ystem in search of data to put into the cache.
Tiger i7320 S5350 Appendix I: Glossar y 6-3 http://www.tyan.com EMRL: Embedded RAID Logic. An Adaptec specific RAID technolog y. ESCD (Extended System Co nfiguration Data ): a format for storing information about Plug- n-Play devices in the system BIOS.
Tiger i7320 S5350 Appendix I: Glossar y 6-4 http://www.tyan.com Latency: the amount of time that one part of a s ystem spends waiting for another part to catch up.
Tiger i7320 S5350 Appendix I: Glossar y 6-5 http://www.tyan.com RAID (Redundant Array of Independent Disks ): a way for the same data to be stored in different places on many hard drives. By us ing this method, the data is stored redundantly, also the multiple hard drives will appear as a si ngle drive to the operating s ystem.
Tiger i7320 S5350 Appendix I: Glossar y 6-6 http://www.tyan.com SSI (Server System Infrastructure): an industr y initiative intended to provide ready-to-use design specifications for commo n server hardware elements (chassis, power supplies, and racks) to promote and support server industry growth.
Tiger i7320 S5350 Technical Support 6-7 http://www.tyan.com Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains.
Tiger i7320 S5350 User’s Manual 6-8 http://www.tyan.com Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 o.
デバイスTyan Computer S5350の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Tyan Computer S5350をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTyan Computer S5350の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tyan Computer S5350の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tyan Computer S5350で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tyan Computer S5350を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTyan Computer S5350の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tyan Computer S5350に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTyan Computer S5350デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。