Ultra Startメーカー2250Mの使用説明書/サービス説明書
ページ先へ移動 of 16
FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
2250 Wiring Diagram Page 3 Pre-Installa tion Page 4 Components Recommended Pre-Installation Procedures Recommended Install Procedures Wire Connectors Page 5 6 Pin Connector 14 Pin Connector 3 Pin Red .
YELLOW WHITE/BLUE BLACK BROWN RED/WHITE PURPLE BLUE/WHITE PINK BLACK/WHITE BLUE WHITE GREEN/WHITE GREEN ORANGE 4 PIN Blu e SIDE VIEW ACTIVE RF ANTENNA Jumpers The jumpers control the output on the white wire from the six pin harness. Place the jumpers in the above order to change the output.
Recommended Pre-Installation Procedures - Control module - Remote transmitter(s) - Antenna with built in program button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness -.
Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. Red 12 power 30amp input Constant 12volt power at ignition harness. Red 12 power 30amp input Constant 12volt power at ignition harness.
QUICK START IN STALL QUICK START IN STALL Yellow Starter Output Connect The Yellow Wire From The 6 Pin T o The Vehicles Starter Wire. Green Heater Output Connect The Green Wire From The 6 Pin To The Vehicles Accessory Wire. Red 12 power Input Connect to Constant 12 Volt Power Source - High Current.
QUICK START IN STALL Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases.
PROGRAM MODE - USER SETTINGS 1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse 2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock *3 0.
PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7 for details on entering program mode Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
1 Type 1 1 Flash Unlock before start and a lock pulse after start & shutdown 2 Type 2 2 Flashes Lock pulse after remote starter shuts off 3* Normal Operation 3 Flashes No additional re-lock pulses 1Negative Input/ 30seconds 1 Flash Waits a maximum 30 seconds before starting.
PROGRAM MODE - TACH SETTINGS Setting 1- Method 2- Low Idle Tach Learning Setting 2- Adjust For Over-Crank (Tach or T achless) Setting 3- Adjust For Under-Crank (Tach or T achless) Shock Sensor - Self Learn Mode Anti Car Jacking Mode Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter.
ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON” steady.
14 INSTALLATION GUIDE OPERATIONS OPERATIONS 1. Press and hold the # button for two seconds. 2. The system will flash the park lights and chirp the siren five times. **This feature can help find your vehicle in a crowded parking lot. 2 sec . 1.Press and hold the UNLOCK button for three seconds.
INSTALLATION GUIDE OPERATIONS OPERATIONS Remote Start Remote Stop Idle Mode Turbo Timer Mode Timer Mode Self Learning Shock Sensor 1.Press and release the button.
Blue Green Lock Un lock V ehicle Lock/Unlock Switch T o Control Relay or Actuators 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Lock Un lock Veh icle Lock/Unlock Switch To C ontrol Relay or Actuato.
デバイスUltra Start 2250Mの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ultra Start 2250Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUltra Start 2250Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ultra Start 2250Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ultra Start 2250Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ultra Start 2250Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUltra Start 2250Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ultra Start 2250Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUltra Start 2250Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。