Vermont CastingメーカーA052041の使用説明書/サービス説明書
ページ先へ移動 of 24
F O R Y O U R S A F E T Y I f y o u sm e l l g a s: 1 S h u t o g a s to th e a p p l i a n c e . 2 E x t i n g u i sh a n y o p e n a m e . 3 O p e n l i d . 4 I f o d or c on t i n u e s, i m m e d i a te l y c a l l y o u r g a s su p p l i e r o r r e d e p a r tm e n t .
T able of Contents Page Number Chapter One - INSTALLATION 4 Necessary Information 4 Choosing a Safe Location 4 Portable L.P. Gas Grills 5 - 7 Important Features of the Series 4000 LP Gas Grill 8 L.
The gas fuel used by this product is highly flammable and must be used in a responsible and cautious manner . It is your responsibility to assemble, operate, and maintain your gas barbecue grill properly .
• The ventilation openings of the cylinder enclosure must be kept free and clear from other debris. 6. Do Not store a spare L.P. gas cylinder under or near this appliance. • Do not store an L.P. cylinder in a build- ing, garage or any other enclosed area.
2. The system has a thermal element that will shut off the flow of gas between 240° F and 300° F . 3. The system has a flow-limiting device which when activated, will limit the flow of gas to 10 cubic feet per hour . 4. The pressure regulator and hose assem- bly provided is factory set at an outlet pres- sure of 11 inches water column (.
L.P. GAS CYLINDER SPECIFICATIONS Any L.P. gas-supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches high. The maxi- mum fuel capacity must be 20 pounds of propane. Full-cylinder weight should be approximately 38 pounds (43.
8 Rear view of Series A052041 grill with the heat shield, gaskets, collar assembly. HEA T SHIELD, GASKETS AND COLLAR W ARNING! Do not remove the heat shield, gaskets, collar assembly from the grill bottom.
Filling a Type 1 Cylinder Valve Example A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting. When using a cylinder exchange, be sure the exchanged cylinder is a T ype 1 cylinder; a 510 POL cylinder will not fit a T ype 1 regulator .
Assembly Instructions Chapter 2 Getting Star ted 1. Please follow the steps in the order that they are presented. 2. Assemble the grill where you plan to use it. 3. Y ou may want to place an old towel or cloth at the assembly site to prevent nuts and bolts from becoming lost.
A ssembly Instructions • Identify the G r ill Parts warming rack (1) cooking grid (1) ceramic briquettes ( 1 package ) rock grate (1) left side table (1) right side table (1) base (1) master hardwar.
HINT: For the first portion of the assembly you will be assembling the grill bottom, pillar and base up- side-down. 1. Position the grill bottom casting upside down so that the heat collar assembly is upward. 2. W orking from the back (open) side of the pillar, set the pillar upside down onto the collar assembly .
back hinge strut pillar bottom grill bottom back gas control valve ends fuel supply hose w/ regulator burner venturi tubes collar 13.
1. Lock the pre-assembled casters on base by pushing down on the latch. 2. Set the base upside-down on onto the pillar bottom as shown on the adjacent page, aligning holes in base with holes in pillar . 3. Insert six bolts through the holes in the pillar and base.
15 ignitor unit base back top pillar black lead wires heat shield bottom casting back.
1 Now with the help of an assistant carefully turn the grill assembly right-side-up. 2. IMPORTANT : Inspect beneath the grill bottom to check that the control-valve ends are still inside the burner venturi tubes. The valve ends must always be inside the burner tubes for the grill to safely operate.
17 A TTENTION PRODUCT ASSEMBLER: Install the X-brace retainer wire across the back of the pillar for warranty validation. 3. Position the wire ends “A” and “B” firmly into the pillar corners behind the bolt heads and against the base. (See Lower Detail.
Locate these parts: 18 tools needed: 3/8" open-end wrench 7/16" open-end wrench A ssembly Instructions • Install the Side T ables. 1/4-20 x 3/4” bolt ( 8 ) Use hardware bag “C”: 1/4-20 hex nut ( 8 ) right side table assembly ( 1 ) 1.
19 3. Insert four 3 /4" bolts through holes in the support brackets of the left side table assembly . 4. Attach the left side table to the four holes located in the left side of the grill bottom using the locking hex nuts provided.
20 A ssembly Instructions • Assemble the G rill Lid tools needed: 7/16" open-end wrench flat-blade screwdriver handle standoff ( 2 ) handle ( 1 ) 1. Position the back of the lid so that the rear holes are in line with the hinge struts on the back of the grill bottom.
7. Raise the lid to attach the front handle. 8. Attach a handle standoff to the front of the grill lid, as shown. 9. Insert one end of the handle into the hole of the standoff. 10.Place other standoff onto handle and while holding the handle in place assem- ble the opposite standoff to the lid in the same manner .
rock grate ( 1 ) No tools are needed. A ssembly Instructions • Installing the In ternal G rill Parts . 22 ceramic briquettes ( 1 box ) warming rack ( 1 ) 1. Place the single rock grate into the grill bottom. cooking grid ( 1 ) 2. Open the package containing the ceramic briquettes and place them on the rockgrate.
3. It is important to properly arrange all the ceramic briquettes onto the rock grate to allow for good air flow during use. NOTICE THE SPACING: The proper amount of briquettes are supplied and there is no need to add more. Some space between the briquettes is necessary.
Replacement parts are available direct from our warehouse. Some components are not available preassembled and may be ordered separately. For convenience, the following parts list is provided along with a representation of the items listed. Charges for replacement parts and shipping may apply .
35 Base Assembly Breakdown of P r eassembled Components Pillar Assembly Bottom/Burner Assembly Side T able Assemblies 1 Base Assembly consisting of: 1 Base SF AH000402 2 Locking Caster AH000303 2 Cast.
デバイスVermont Casting A052041の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Vermont Casting A052041をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVermont Casting A052041の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vermont Casting A052041の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vermont Casting A052041で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vermont Casting A052041を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVermont Casting A052041の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vermont Casting A052041に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVermont Casting A052041デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。