VXIメーカーB100の使用説明書/サービス説明書
ページ先へ移動 of 26
User Guide A brand of VXI Corporation One Front Str eet. Rollinsford, NH 03869 800-742-8588 I 603-742-2888 Bringing freedom to personal communications www .
Blue Parrott B100 Wireless Headset 1.
Blue Parrott B100 Wireless Headset 2 T ABLE OF CONTENTS Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Basic Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .
VXI LIMITED WARRANTY VXI consumer products (one year warranty) 1. VXI warrants that your Blue Parrott B100 system will be free from defects in material and workmanship for one year from the date of purchase.
company may request that you disconnect the equipment until the problem is resolved. 9. Repair of this product must be handled by VXI Corporation. F or more information about repairs, please read the warranty section of this user guide or call VXI Corporation at 1-800-742-8588.
Blue Parrott B100 Wireless Headset PRODUCT FEA TURES Blue Parrott B100 Headset 5 Multifunction Button Indicator Lights Volume (Increase) / Microphone Mute Control Volume (Decrease) Control Noise Cance.
Blue Parrott B100 Wireless Headset F AQ’S Why don’t I hear a dial tone? 1. Make sure the headset is in Standby Mode. The yellow light on the headset should be flashing every few seconds when it is r emoved from the base. 2. Be sure the telephone line from the wall is connected to the Blue Parrott B100 base (not into the phone).
Blue Parrott B100 Wireless Headset GLOSSARY OF TERMS Standby Mode – Headset is on and ready to get a dial tone, answer , or end a call. Standby Mode is automatic when removing headset fr om the base. T urning off the headset while it is out of the base takes it out of Standby Mode.
2. Follow the alternate headset’ s user instructions for putting the headset into pairing mode. 3. Press and hold down the pairing button on the B100 base for approximately 5 to 15 seconds until the red and orange indicator lights on the base begin to flash alternately .
INST ALLA TION The Blue Parrott B100 connects directly into the phone line wall jack. Y ou may add a telephone dir ectly to the B100 system, or you can install the B100 independently to its own telephone wall jack.
the call (see Switch From Handset T o Headset While On A Call on page 15). Or if desir ed, you may initiate three-way conferencing via the headset, as follows: 1. Be sure the headset is in Standby Mode. 2. Press the Multifunction button for 1 second, and r elease.
The headset’ s audio and visual indicators will indicate the level of available battery power as follows. When headset is in base: • Green light : Fully charged. • Red light : Normal charging/Okay to use. When headset is r emoved from base: • Flashing red light every few seconds : low battery warning.
End the Call Quickly pr ess the multifunction button on the headset for 1 second. Afterwards, you will hear a single beep. The call will be disconnected and the headset will revert to Standby Mode. Adjust Receive Volume T o adjust the volume in your earpiece, press the increase or decrease volume button for 1 second, then release.
BASIC OPERA TIONS See page 5 for location of button controls. Standby Mode The headset is automatically in standby mode when you remove it from the base; therefor e, a single pr ess of the multifunction button will obtain a dial tone, answer an incoming call, or end a call.
BASIC OPERA TIONS See page 5 for location of button controls. Standby Mode The headset is automatically in standby mode when you remove it from the base; therefor e, a single pr ess of the multifunction button will obtain a dial tone, answer an incoming call, or end a call.
End the Call Quickly pr ess the multifunction button on the headset for 1 second. Afterwards, you will hear a single beep. The call will be disconnected and the headset will revert to Standby Mode. Adjust Receive Volume T o adjust the volume in your earpiece, press the increase or decrease volume button for 1 second, then release.
The headset’ s audio and visual indicators will indicate the level of available battery power as follows. When headset is in base: • Green light : Fully charged. • Red light : Normal charging/Okay to use. When headset is r emoved from base: • Flashing red light every few seconds : low battery warning.
the call (see Switch From Handset T o Headset While On A Call on page 15). Or if desir ed, you may initiate three-way conferencing via the headset, as follows: 1. Be sure the headset is in Standby Mode. 2. Press the Multifunction button for 1 second, and r elease.
INST ALLA TION The Blue Parrott B100 connects directly into the phone line wall jack. Y ou may add a telephone dir ectly to the B100 system, or you can install the B100 independently to its own telephone wall jack.
2. Follow the alternate headset’ s user instructions for putting the headset into pairing mode. 3. Press and hold down the pairing button on the B100 base for approximately 5 to 15 seconds until the red and orange indicator lights on the base begin to flash alternately .
Blue Parrott B100 Wireless Headset GLOSSARY OF TERMS Standby Mode – Headset is on and ready to get a dial tone, answer , or end a call. Standby Mode is automatic when removing headset fr om the base. T urning off the headset while it is out of the base takes it out of Standby Mode.
Blue Parrott B100 Wireless Headset F AQ’S Why don’t I hear a dial tone? 1. Make sure the headset is in Standby Mode. The yellow light on the headset should be flashing every few seconds when it is r emoved from the base. 2. Be sure the telephone line from the wall is connected to the Blue Parrott B100 base (not into the phone).
Blue Parrott B100 Wireless Headset PRODUCT FEA TURES Blue Parrott B100 Headset 5 Multifunction Button Indicator Lights Volume (Increase) / Microphone Mute Control Volume (Decrease) Control Noise Cance.
company may request that you disconnect the equipment until the problem is resolved. 9. Repair of this product must be handled by VXI Corporation. F or more information about repairs, please read the warranty section of this user guide or call VXI Corporation at 1-800-742-8588.
VXI LIMITED WARRANTY 1. VXI warrants that your Blue Parrott B100 system will be free from defects in material and workmanship for two years from the date of purchase.
User Guide A brand of VXI Corporation One Front Str eet. Rollinsford, NH 03869 800-742-8588 I 603-742-2888 Bringing freedom to personal communications www .
デバイスVXI B100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
VXI B100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVXI B100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。VXI B100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。VXI B100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
VXI B100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVXI B100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、VXI B100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVXI B100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。