Wayne-Daltonメーカー452の使用説明書/サービス説明書
ページ先へ移動 of 20
IMPOR T ANT SAFETY NO TICES This manual MUST be attached to the wall in c lose proximity to the door . Model 451/452 Read these instructions car efully befor e attempting installation. If in question about any of the pr ocedur es, do not perform the work.
2 Dim. Y INDICA TES THE DIST ANCE FROM THE HEADER TO THE CENTER LINE OF TORSION SHAFT . NOTE: 2 1/2” OF ADDITIONAL HEADROOM IS REQUIRED FOR SINGLE TROLLEY OPERA TOR INST ALLA TIONS. NOTE: HEADROOM CAN BE REDUCED 2-1/2” BY USING THE QUICK CLOSING TOP FIXTURE OR BY SHORTENING THE VER TICAL TRACKS BY 3” MAX.
3 PRECAST W ALL WITH CORNER ANGLE 3” TRACK PRECAST W ALL WITHOUT CORNER ANGLE 3” TRACK STEEL JAMBS 2” TRACK PRECAST W ALL WITH CORNER ANGLE 2” TRACK PRECAST W ALL WITHOUT CORNER ANGLE 2” TRA.
4 COUNTERBALANCE CABLES/ BO TTOM BRACKETS For doors using the broken cable safety device, see page 19. For Model 451 doors with the bottom bracket shown in FIG A , locate the bottom section and the left and right hand bottom brackets. Secure the counterbalance cables to the brackets using clevis pin, washer and cotter key as shown in FIG A .
5 1/4” 7/8” SELF- DRILLING SCREWS A TT ACHED HINGE 1/4” X 7/8” SELF- DRILLING SCREWS A TT ACHED HINGE HINGES NOTE: T op sections do not require hinges.
6 BO TTOM SECTION/ VERTICAL TRACK Center and level (or support to a known grade level) the bottom section in the opening, using shims if necessary , as seen in FIG H . T emporarily attach the wall angles to the jambs with the appropriate lag screws, as shown in FIG H-1 , FIG H-2 and FIG H-3 .
7 FIG J (4) 1/4”- 20 X 7/8” SELF DRILLING SCREWS TOP BRACKET BASE END STILE TOP SECTION TOP SECTION TOP BRACKET BASE FLANGE HEX NUT (1) 5/16” X 3/4” CARRIAGE BOL T TOP BRACKET SLIDE TOP BRACKE.
8 VERTIC AL TRACK ADJUSTMENT Adjust the spacing of the vertical tracks from 3/8”-5/8” spacing a t the bottom section to 3/4”-7/8” spacing at the top section; refer to page 3.
9 FIG L THIS ILLUSTRA TION SHOWS 15” RADIUS TRACK W/SELF DRILLING SCREW TO STEEL THIS ILLUSTRA TION SHOWS 15” RADIUS TRACK W/CONCRETE ANCHOR THIS ILLUSTRA TION SHOWS 12” RADIUS TRACK W/LAG BOL T TO WOOD. (3) 3/8” X 3/4” TR USS BOL TS AND NUTS.
10 FIG N ONE or TWO SPRINGS (2” or 2-5/8” ONL Y) LEFT HAND DRUM RED WINDING CONE BLACK RIGHT HAND DRUM BLACK WINDING CONE RED 3” MINIMUM SPRING PAD WIDTH (6” IF FOR TROLLEY OPERA TOR) CENTER S.
11 FIG P FIG O RIGHT HAND DRUM BLACK COUPLING LEFT HAND DRUM RED WINDING CONE RED WINDING CONE BLACK TWO OR MORE SPRINGS (2-5/8” or 3-3/4”) SPLIT SOLID SHAFT 17” MINIMUM SPRING P AD WIDTH 13” .
12 DOOR HEIGHT 400-8 400-12 5250-18 800-32 6’6” 7.5 7.5 7’0” 7.875 7.875 7’6” 8.5 8.5 8’0” 8.875 8.875 6.75 8’6” 9.25 7.125 9’0” 9.5 7.375 9’6” 10.125 7.75 10’0” 10.5 8.125 5.375 10’6” 11 8.375 5.625 11’0” 11.5 8.
13 FIG R REAR SUPPORTS After spring(s) are wound, cautiously remove locking pliers from vertical tracks, while pushing downward on door to prevent it from raising unexpectedly , in case spring(s) were over wound. Carefully and slo wly raise door , until one and a half sections are in the horizontal tracks.
14 FIG S SPRING ADJUSTMENTS Release the locking pliers from vertical tracks and check the door’ s counterbalance. Adjust springs if necessary . If door does not balance properly , verify that all supplied components such as struts are installed. Verify quantity , wire diameter , spring size & drums to the spring tag.
15 BOL T “Z” SHAPED ASSEMBL Y USING (4) 3/8” X 1-1/4” BOL TS AND NUTS GIRT GIRT (2) 3/8” X 1-1/4” BOL TS TO SECURE BRACKET TO ANGLE HEAVY PERFORA TED ANGLE (1-5/8 X 2-3/8” X 11 GA.
16 FIG X STEP PLA TE INST ALLA TION Position your step plate, on the inside of the door , over the bottom section end stile on the side of the door containing the side lock. Secure step plate to endstile with (2) 1/4”-20 x 7/8” Self-drilling screws, as shown in FIG W .
17 CABLE KEEPER INST ALLA TION Place cable keeper between roller carrier tabs. Insert roller through holes in the tabs and through cable keeper . Rotate arm up and hook around cable, letting cable keeper arm pull against the counterbalance cable, keeping it taut, as shown in FIG Y .
18 SINGLE TROLLEY OPERA TOR BRACKET IS DOOR SIZE DEPENDENT . TROLLEY OPERA TOR BRACKET IS SUPPLIED BY OTHERS COUPLING 5” MIN. EXTRA HEADROOM REQUIRED 1/2” X 3” MIN. SLEEVE ANCHOR (BY OTHERS), 5/16” X 1” SELF-DRILLING AND T APPING SCREW OR 5/16” X 1-5/8” LAG BOL T 1/2” X 3” MIN.
19 MAINTENANCE AND FINISHING INSTRUCTIONS MAINTENANCE An occasional light cleaning will also help maintain an aesthetically pleasing appearance. The only regular maintenance necessary is that of annual washing.
20 Limited Warranty Model 451, 452 & K-AL Subject to the terms and conditions contained in this Limited Warranty, Wayne-Dalton Corp. (“ Manufacturer”) warrants the sectio ns of the door for FIVE (5) YEARS with the exception of the following items.
デバイスWayne-Dalton 452の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wayne-Dalton 452をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWayne-Dalton 452の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wayne-Dalton 452の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wayne-Dalton 452で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wayne-Dalton 452を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWayne-Dalton 452の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wayne-Dalton 452に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWayne-Dalton 452デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
