Weberメーカー2000 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 36
Serial Number Please use this number in registering your warranty and any correspondence with the factory. W E B E R W E B E R GENESIS ® 2000 Series LP Gas Barbecue Owner’ s Manual National Association PROPANE GAS ® 98615 10/97 W ARNING: Do not try to light this appliance without reading "Lighting" instructions section of this manual.
2 D ANGER Failure to f ollow the Dangers, W arnings and Cautions contained in this Owner’ s Manual may result in serious bodil y injury or death, or in a fire or an explosion causing damage to property . W ARNINGS Do not store a spare or disconnected LP tank under or near this barbecue .
3 Weber-Stephen Products Co. (W eber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue that it will be free of defects in material and workmanship from the date of purchase as foll.
© 1997 Weber . Weber , , Genesis, Flavorizer and Crossover are registered U.S. trademarks; Perma-Mount, Gas Catcher , FlameCheck, Steam-N-Chips, Spider Stopper , and W arm-Up are U.S. trademarks of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266.
5 Contents WARNINGS ................................................................ 2 Warranty & Patents.................................................. 3-4 General Instructions .................................................... 6 Assembly ..
6 General Instructions Your Weber Gas Barbecue is a portable outdoor cooking appliance. With the Weber Gas Barbecue you can grill, barbecue, roast and bake with results that are difficult to duplicate with indoor kitchen appliances. The closed lid and Flavorizer Bars produce that "outdoor" flavor in the food.
Step 1 Check package contents Cooking box (assembly) Lid (assembly) LP tank LP tank filler adapter Bottom tray T wo work tables T wo accessory trays Swing table 7 Assembl y T ools needed Screwdriver Phillips screwdriver Hammer 7/16 inch or an adjustable wrench Pliers Block of wood Supplies needed Y our LP tank is shipped empty for safety .
Control panel Front panel Left frame Wheel frame T wo frame connectors T ank panel assembly Five long Flavorizer Bars Eight short Flavorizer Bars T wo wheels T wo aluminum drip pans Catch pan Axle 8 R.
T wo 10-24 x 1 3/4 machine screws (actual size) T wo 10-24 hex nuts (actual size) Eighteen 1/4 inch nylon washers (actual size) 1/4-20 keps nut 1/4-20 x 1 1/4 inch bolt (actual size) 1/4-20 hex nut (a.
10 Step 2 Assemble wheels Y ou will need: axle, two wheel hubcaps, two wheels, wheel frame, hammer and a block of wood. Place one end of the axle on the block of wood (or other protected surface). T ap on one hubcap. Put one wheel on the axle, WEBER side toward the hubcap.
11 Step 4 Continue frame assembly Y ou will need: frame assembly , wheel frame assembly , front panel, caster frame, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 inch wrench. Place the caster frame onto the tabs of the left frame with the dimple to the inside.
12 Burner tubes Figure 6 Frame brace Step 7 Add cooking box Y ou will need: frame assembly , cooking box assembly , 1/4-20 x 2 inch bolt, 1/4 inch nylon washer , 1/4-20 keps nut , pliers and a 7/16 inch wrench. T urn frame assembly right side up. Uncoil the hose.
13 Step 9 Install tank panel assembly Y ou will need: tank panel assembly , 1 1/4 inch bolt, 1/4-20 hex nut, 1/4 inch nylon washer and a 7/16 inch wrench. Insert the tank panel tabs into the slots in the frame brace. Slide up until the notch at the bottom of the tank panel fits over the cross brace.
14 Step 11 Install igniter Note - The igniter wires are already attached to the Gas Catcher Ignition Chamber and the igniter . This was done to f actory test the ignition system. The igniter lock nut is on the igniter . Insert the top of the igniter up through the large part of the keyhole in the frame brace.
15 Step 12 Set LP fuel scale Y ou will need: LP tank (empty). Note - F or accuracy , the fuel scale must be set with an empty tank. We utilize various LP tank manufacturers. Some of the tanks we receive have differing top collar assemblies. (The top collar is the metal protective ring around the valve.
16 Route the hose so it will not interfere with the scale indicator rod. The hose and regulator are connected in the following manner: Slide back the collar of the quick disconnect on the tank valve. Push the male fitting of the regulator into the quick disconnect, and maintain pressure.
17 Step 16 Check for gas leaks D ANGER Do not use an open flame to chec k f or gas leaks. Be sure there are no sparks or open flames in the area while y ou chec k for leaks. This will result in a fire or e xplosion which can cause serious bodil y injury or death and damage to pr operty .
18 Step 17 Install Flavorizer Bars and Cooking Grates Y ou will need: five long Flavorizer Bars, eight short Flavorizer Bars and two cooking grates. Set the long Flavorizer Bars side to side in the lower position, then set the short Flavorizer Bars front to back in the upper position in the cooking box.
19 Step 19 Install the lid Y ou will need: lid, two hinge pins and two hair pin cotters. Set the lid in place from the rear of the barbecue. Close and align the hinge at the rear . Insert hinge pins from the outside through the hinge. Insert hair pin cotters into the small holes in the hinge pins.
20 Slot in frame (view from below) Insert one end of the hinge rod into the hole in the frame. Figure 27 (a). Insert the other end into the hole in the swing table end bracket. Figure 27 (b). Hold the end bracket at an angle so the lower tab is inside the frame tube.
21 Position slide bar assembly on the outside of the caster frame. Put a nylon washer on each 1 3/4 inch screw , insert screws through frame and slide bar assembly and add nylon washers and hex nuts. T ighten nuts using a screwdriver and pliers. Figure 28.
22 Lighting Summary lighting instructions are on the control panel. 2 1 7 3 4 5 6 8 Figure 1 Crossover Ignition System W ARNING: The burner contr ol knobs must be in the OFF position before turning on the LP tank v alve.
23 4) Turn the tank on by turning the tank valve counterclockwise. 5) Strike a match and put the flame into the matchlight hole in the front of the cooking box. W ARNING: Do not lean over open barbecue. Keep your face and bod y at least one foot a way fr om the matchlight hole when lighting the barbecue.
24 Cooking W ARNING: Do not move the W eber Gas Barbecue when operating or hot. Y ou can adjust the FRONT , CENTER and BACK burners as desired. The control settings High (H), Medium (M), Low (L), or Off (O) are described in your Weber cookbook. The cookbook uses these notations to describe the settings of the FRONT , CENTER, and BACK burners.
25 Scale setting wing nut T ank lock wing nut T ank valve Collar (a) (b) Figure 3 Refilling the LP tank We recommend that you refill before the scale indicator reaches "E".
26 c) Connect the hose to the tank. Route the hose so it does not interfere with the scale indicator rod. Slide back the collar of the quick disconnect on the tank valve. Figure 5 (a). Push the male fitting of the regulator into the quick disconnect, and maintain pressure.
27 Safe handling tips f or LP Gas ■ Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas. LP gas is a gas at regular temperatures and pressures. Under moderate pressure, inside a tank, LP gas is a liquid. As the pressure is released the liquid readily vaporizes and becomes gas.
28 Check: a) Hose to manifold connections. Figure 8 (a). b) Regulator to tank connection. Figure 8 (b). W ARNING: If there is a leak at connection (a), retighten the fitting with a wrench and rechec k for leaks with soap and water solution. If a leak persists after retightening the fitting, turn OFF the gas .
29 General Maintenance W eber Spider Stopper Guards Y our Weber Gas Barbecue, as well as any outdoor gas appliance, is a target for spiders and other insects. They can nest in the venturi section of the burner tubes. This blocks the normal gas flow , and can cause the gas to flow back out of the air shutter .
30 g) Lift and twist the burner assembly slightly , to separate the crossover tube from the burners. Figure 17. Remove the burners from the cooking box.
31 Crosso ver Ignition System Operations If the Crossover Ignition System fails to ignite the Front burner , light the Front burner with a match. If the Front burner lights with a match, then check the Crossover Ignition System. ■ Check that both the white and black ignition wires are attached properly .
32 Prob lem Burners b urn with a yellow or orange flame, in conjunction with the smell of gas. Burners do not light. -or - Burners ha ve a small flickering flame in the HIGH position. -or- Barbecue temperature only reaches 250˚ to 300˚ degrees in the HIGH position.
.
34 ® ® ® ® ® ® ® ® W E B E R W E B E R 1 2 4 5 6 7 8 9 10-11 13 14 15, 11 22 24 26 27 28 29 30 31 32 64 62-63 56 55 8 53 51 50 49 48 47 45 44 43 42 41 40 39 54 11 33 11 38 34 52 46 25 12 23 16.
35 1 Lid (assembly) 2 Lid handle 3 W arm-Up Basket 4 W arming rack 5 Short Flavorizer Bars (8) 6 Long Flavorizer Bars (5) 7 Cooking grates (2) 8 Work tables (2) 9 T ubing plugs (5) 10 1/4-20 x 2 inch .
A F INAL W ORD OF T HANKS hank you for choosing a W eber Barbecue. Our family her e at W eber has worked hard to produce the highest quality products for your satisfaction.
デバイスWeber 2000 Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weber 2000 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeber 2000 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weber 2000 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weber 2000 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weber 2000 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeber 2000 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weber 2000 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeber 2000 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
