Wiltonメーカー2221VSの使用説明書/サービス説明書
ページ先へ移動 of 28
Operating Instructions — Parts Manual 20-Inch VS Drill Press Models: 2221VS, 2223VS, 2232AC, 2234AC Serial Number 201001 and greater WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60124 Part No. 5510374 Ph.: 800-274-6848 Revision D6 08/06 www .wmhtoolgroup.
.
3 T able of Content s Cover Page ....................................................................................................... 1 General S pecifications ...................................................................................... 4 Operating Precautions .
4 General S pecifications The Wilton 20 Inch V ariable S peed Drill presses Models 2221VS, 2223VS, 2232AC, and 2234AC are available in manual speed control or inverter speed control configuration. Electrical power options are single-phase, 1 15 and 220 volts, or 3-phase, 440 volts.
5 supply while servicing. - Always follow instructions in Operating Instructions and Parts Manual when changing accessory tools or parts. - Never modify the machine without consulting Wilton Corporation. Y ou—the st ationary power tool user— hold the key to safety .
6 A WG (American wire gauge) number Conductor length 240 volt lines 120 volt lines 0-50 feet No. 14 No. 14 50-100 feet No. 14 No. 12 Over 100 feet No. 12 No.8 General electrical cautions This drill press should be grounded in accordance with the National Electrical Code and local codes and ordinances.
7 Introduction This manual includes operating and maintenance instructions for the Wilton Model 2221VS, 2223VS, 2232AC and 2234AC V ariable S peed Drill Presses. This manual also includes parts listings and illustra- tions of replaceable parts. Wilton Model 2221VS and 2223VS drill presses feature manual speed control.
8 Raising the Drill Head and T able The drill press is shipped with the table and drill head supported by wooden blocks near the bottom of the column. The head is raised to the operating position using a strap and hoist, then secured to the column by tighening the hex cap screw .
9 Figure 4: Control Panel (Inverter Speed Control) Drilling Speed Chart A DRILLING SPEED CHART is provided on the front panel. The chart can be used to select the speed required for various drill sizes (0.196 inch to 1.000 inch — 5 mm to 25 mm) and materials (steel, cast iron, aluminum, and copper).
10 Replacement of Drive Belt W ARNING: MAKE SURE TO DISCONNECT ELECTRICAL POWER TO THE DRILL PRESS TO A VOID THE POSSIBILITY OF INADVERTENT OPERA TION AND EXPOSURE T O POTENTIALL Y LETHAL VOL T AGE LEVELS. Manual Speed Control - Models 2221VS and 2223VS 1.
11 W ARNING: CHANGE THE RADIAL POSITION OF THE DRILL HEAD ONL Y IF THE DRILL PRESS BASE IS SECURED TO THE FLOOR. SWINGING THE DRILL HEAD WITHOUT THE BASE BEING SECURED TO THE FLOOR WILL CAUSE THE DRILL PRESS T O BECOME UNST ABLE AND TIP OVER RESUL TING IN INJUR Y AND/OR DAMAGE TO THE MACHINE.
12 Feeds for Drilling The feed of a drill is governed by the size of the tool and the material drilled. Because the feed rate partially determines the rate of production and also is a factor in tool life, it should be chosen carefully for each job.
13 Wiring Diagram - Models 2221 & 2223.
14 Wiring Diagram - Models 2232AC & 2234AC LED Display Connection 0 220 AC Power Sensor V olts - + Input 3 Phase 220/440.
15 T roubleshooting Problem Possible Cause Remedy S pindle does not turn. 1. Motor overload protector tripped. 1. Press motor overload reset button. 2. Circuit breaker tripped. 2. Reset circuit breaker . 3 . Branch circuit breaker tripped or fuse blown.
16 Optional Equipment Coolant System Installation 1. Remove the large reservoir cover plate from the machine base. T ap 1/4-20 threads in the 4 pilot holes. Install the cover plate back onto the machine base. 2. Insert the pump into the opening, utilize the screws from the small round cover plate to fasten the pump to the base.
17 Replacement Part s This section provides exploded view illustrations that show the replacement parts for Wilton Model 2221VS, 2223VS, 2232AC, and 2234AC 20-Inch Drill Presses. Also provided are parts listings that provide part number , description, and quantity .
18 Exploded V iew — Drill Head — Manual S peed Control (Models 2221VS and 2223VS).
19 7 5510077 Pulley , S pindle S tep 1 8 5510078 Nut, S pindle 1 9 5510079 V -Belt 1 10 5510080 Pulley , S pindle, VS, Lower 1 1 1 5510081 Pulley , S pindle, VS, Upper 1 1 1A 5513673 Screw , Cap 1 1 1.
20 Exploded View — Drill Head — Inverter S peed Control (Models 2232AC and 2234AC).
21 Item Part No. Number Description Qt y 1 5517332 Casting, Head 1 2 5510142 W indow , Oil 1 3 5510143 Bearing, Ball 1 4 5510144 Ring, Retaining 1 5 5510145 Gear (32T) 1 6 5510146 Key 1 7 5510147 Shaf.
22 Item Part No. Number Description Qt y 85-1 5517371 W asher , Flat 4 85-2 5517372 Screw 4 86 5517373 Sub-Panel 1 86-1 5517374 Screw 4 87 5510235 T erminal Block 1 88 5517375 Rail, Mounting 1 89 5510.
23 Exploded View — S pindle Components (All Models).
24 Item Part No. Number Description Qt y 1 5517332 Casting, Head 1 2 5517376 Bolt, Hex, Shoulder 2 2- 1 5517377 S pring 2 3 5517378 Rod, Cam Lock 2 4 5510250 Nut, Hex 2 5 5510251 Wrench, Hex Head 1 7 .
25 Exploded View - T able and Base (All Models).
26 Item Part No. Number Description Qt y 1 5510288 Base 1 2 5510289 Plate, Coolant Cover 1 3 5510456 Pump, Coolant, 1 15V , 1P 1 5512103 Pump, Coolant, 220/440V 3P 1 4 5510291 Bolt, Hex 4 5 5517388 Sc.
.
WMH TOOL GROUP 2420 V antage Drive Elgin, IL 60123 Phone: 800-274-6848.
デバイスWilton 2221VSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wilton 2221VSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWilton 2221VSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wilton 2221VSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wilton 2221VSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wilton 2221VSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWilton 2221VSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wilton 2221VSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWilton 2221VSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。