YamahaメーカーACD1の使用説明書/サービス説明書
ページ先へ移動 of 25
EN Reference Manual.
ACD1 Reference Manual 2 Contents Introduction............................................. 3 About the documentation ................................. 3 Supported amplifiers ......................................... 3 Setup ...........................
ACD1 Reference Manual 3 Intr oduction About the documentation This document explains mainly the operation and specifications of the A CD1 amplifier control de vice itself. When using the A CD1, y ou will also need to consult various manuals other than this document.
ACD1 Reference Manual 4 Introduction T erms This section explains terminology specific to the A CD1. ■ Amp Editor This is computer application software. W ith this software, you can use your computer to monitor and control the A CD1 and the amplifiers connected to the A CD1.
ACD1 Reference Manual 5 Contr ols and Connectors q Display This sho ws information about the scene, the A CD1 itself, or the connected amplifiers. This will light red when an abnormal- ity (a W ARNING or higher alert) occurs. This will also blink blue and white when the Identify operation is performed in Amp Editor.
ACD1 Reference Manual 6 Controls and Connectors y Ground scre w The A C power cord is a 3-wire type. If the A C outlet used is earthed (grounded), this de vice will be properly earthed as well. Also, grounding the scre w sometimes reduces hum and interference noise.
ACD1 Reference Manual 7 Panel operations By pressing b uttons on the panel you can monitor or contr ol various parameters of the A CD1 itself or of the con- nected amplifiers. The f ollowing parameters can be monitor ed/controlled. Category Sub category Operation performed 1.
ACD1 Reference Manual 8 Panel operations The main roles of each b utton are as follo ws. As an example, we’ll explain how to stor e the scene of an amplifier connected to the A CD1.
ACD1 Reference Manual 9 Panel operations 5. Use the [ ▲ INC/YES] / [ ▼ DEC/NO] b uttons to select the ID of the amplifier f or which you want to stor e settings. 6. Press the [NEXT] b utton to move to the scene number . 7. Use the [ ▲ INC/YES] / [ ▼ DEC/NO] b uttons to select the scene number that y ou want to store.
ACD1 Reference Manual 10 Panel operations Here’ s how to r ecall or store scenes for a specified amplifier . ■ Recalling a scene (“1. Scene” ➝ “Recall”) Recalls a scene for the specified amplifier . • If you select “ALL ” as the Amp ID , the scene name will not be displayed.
ACD1 Reference Manual 11 Panel operations These settings allow y ou to control an amplifier connected to the A CD1. ■ Po wer on/standb y (“2. Amp Contr ol” ➝ “Standby”) Switches the po wer of the specified amplifier between On and Standby .
ACD1 Reference Manual 12 Panel operations This indicates the output lev el of the amp connected to the A CD1. ■ Amplifier output (“3. Output Monitor”) Displays the output le vel for each channel of the specified amplifier .
ACD1 Reference Manual 13 Panel operations ■ Identify (“4. Device Setup” ➝ “Identify”) Blinks the “Identify” icon of the corresponding A CD1 in Amp Editor. Here y ou can make overall settings f or the A CD1 and view various types of inf ormation.
ACD1 Reference Manual 14 Panel operations ■ LCD bac klight (“5. Utility” ➝ “LCD Bac klight”) This specifies the lit status of the A CD1’ s LCD backlight. ■ Restricting panel operations (“5. Utility” ➝ “P anel Operation”) Here you can turns panel operation lock on/of f.
ACD1 Reference Manual 15 Panel operations ■ Enabling scene recall operations via EMG commands (“5. Utility” ➝ “EMG Scene Setup”) Specifies whether the EMG scene will be recalled when the EMG (Emer - gency) signal is recei ved. The follo wing three types of EMG signal can be recei ved.
ACD1 Reference Manual 16 Panel operations ■ GPI IN calibration (“5. Utility” ➝ “GPI Calibration”) Calibrates the detected range of the [GPI IN] connector input v oltage. Here y ou can make network settings f or the A CD1. ■ IP Address Mode setting (“6.
ACD1 Reference Manual 17 Panel operations ■ Po rt settings f or an external contr oller (“6. Network Setup” ➝ “IP Ctrl P or t #”) Here you can specify the port number that will be used to control the A CD1 from an external de vice such as an AMX or Crestron unit.
ACD1 Reference Manual 18 Connector wiring This section explains how to wir e the [GPI] and [F A UL T OUTPUT] connectors located on the A CD1’s r ear panel. Be sure to use the supplied Eur oblock connector . If you lose the connector , contact your Y amaha dealer .
ACD1 Reference Manual 19 Connector wiring Connect GPI (General Purpose Interface) de vices (e.g., contr ol- lers) to the rear panel [GPI] connector . Y ou can use GPI to send or r eceive contr ol signals to or from an external de vice. The A CD1 provides 4-port input and 4-port output.
ACD1 Reference Manual 20 Connector wiring Y ou can connect a lamp etc. to the r ear panel [F A UL T OUTPUT] connector to indicate that an abnormality has occurred. The [F A UL T OUTPUT] connector consists of NO (Normally Open), C (Common), and NC (Normally Closed).
ACD1 Reference Manual 21 Appendix Messages that may appear in the A CD1’ s display and the appropriate responses ar e listed below . F or more about alert messages, refer to the Amp Editor o wner’ s manual. The A CD1 allows the f ollowing single-byte characters to be displayed and input.
ACD1 Reference Manual 22 Appendix Tr oubleshooting Symptom P ossible causes Response All scene data sav ed in the ACD1 has disap- peared The power w as tur ned off while the ACD1’ s data was being sa ved Once again synchronize the unit with Amp Editor to transmit the settings from Amp Editor.
ACD1 Reference Manual 23 Appendix *1 Suppor ted models XP7000, XP5000, XP3500, XP2500, XP1000, XM4180, XM4080, XH200 Guaranteed cable length: 50m *2 Suppor ted models T5n, T4n, T3n, PC9501N, PC6501N, .
ACD1 Reference Manual 24 Appendix Unit : mm * Specifications and descr iptions in this owner’ s manual are for inf or mation purposes only . Y amaha Cor p . reserves the right to change or modify products or specifications at any time without prior notice.
U .R.G., Pro Audio & Digital Musical Instrument Division, Y amaha Corporation © 2009 Y amaha Corporation 911-PO-C0.
デバイスYamaha ACD1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yamaha ACD1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha ACD1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha ACD1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha ACD1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha ACD1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha ACD1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha ACD1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha ACD1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。