YeomanメーカーCL MILNER BRICK YMの使用説明書/サービス説明書
ページ先へ移動 of 32
PM559 - Issue 1 (June 201 1) Y eoman CL Milner Brick Inset Convector Stove MODELS: YMMB Instructions for Use, Installation and Servicing For use in GB & IE (Great Britain and Republic of Ireland).
COVERING THE FOLLOWING MODELS: YMMB 2 COMMISSIONING 23 MAINTENANCE & SERVICING 24 Annual Service 24 Removal of Log Guard 25 Removal of Baffle 25 Removal of Grate 25 Removal of Fire Bricks 25 Fitti.
3 APPLIANCE COMMISSIONING CHECKLIST To assist us in any guarantee claim please complete the following information. In the unlikely event of a problem, contact your installer or retailer for assistance: Retailer appliance was purchased from Name: .....
4 USER INSTRUCTIONS 1. GENERAL POINTS 1.1 Before installation and/or use of this appliance please read these instructions carefully to ensure that all requirements are fully understood. The appliance must be fitted by a registered installer*, or approved by your local building control officer.
5 USER INSTRUCTIONS AIRWASH AND PRIMARY AIR CONTROLS 3 PR9025 Op en C los e Op en C los e Airwash Control Primary Air Control SECONDARY AIR CONTROLS 4 PR9026 Secondary Air Control In - Closed Out - Open DOOR HANDLE 1.13 Use a protected gloved hand to operate.
6 USER INSTRUCTIONS 3. RECOMMENDED FUELS 3.1 Wood Logs: Burn only seasoned timber with a moisture content of less than 20%. To ensure this allow cut wood to dry for 12 to 18 months. Wood Length 6 Appliance Wood Length CL Milner Brick 250mm Poor quality timber: — Causes low combustion efficiency.
7 USER INSTRUCTIONS 5.5 When in use, burning the appliance at a high temperature for a short period also reduces tars and creosotes. WARNING: DO NOT OPERATE THE APPLIANCE WITH THE PRIMARY AIR CONTROL OPEN FOR LONG PERIODS OF TIME AS THIS COULD CAUSE OVER- FIRING AND MAY CAUSE PERMANENT DAMAGE.
8 USER INSTRUCTIONS 6. BURNING TIPS 6.1 Fuel Quality (Wood) Use wood with a moisture content of less than 20%. Seasoned logs have the bark beginning to lift and peel away and cracks radiating from the centre. They feel lighter than fresh cut wood of a similar size and sound hollow when struck against each other.
9 7. ASH REMOVAL Do not allow ash to build up in the appliance as it will not burn properly and may cause damage. 7.1 Wood — Open doors and using gloves remove ashpan with the tool provided (see Diagram 10). — Remove ash and place into a Yeoman Ash Caddy (Yeoman Part No.
10 13. CHIMNEY SWEEPING 13.1 To maintain safe and efficient use of the appliance, the chimney/flue must be inspected and swept at least once a year by a qualified chimney sweep**. If the appliance is used continuously throughout the year, or it is used to burn wood or smokeless fuel, more frequent sweeping is recommended.
11 16.3 Glass cracking Do not over tighten the screws on the glass clamp when replacing the glass. This causes stress and the intense temperature changes can cause the glass to crack.
12 TECHNICAL SPECIFICATION CL MILNER BRICK • PrimaryAir (undergrate airfor fullMulti-fuel use). • Airwash(for woodburning/clean glass). • Adjustablesecondary air(to ensurecomplete burningof flue gases).
13 SITE REQUIREMENTS CL INSET DIMENSIONS PR9036 369 379 593 577 281 520 243 540 103 282 183 104 156.
14 1. FLUE OR CHIMNEY 1.1 The flue or chimney system must be in good condition. It must be inspected by a competent person and passed for use with the appliance before installation. Products of combustion entering the room can cause serious health risks.
15 3.1 The appliance must stand on a non-combustible constructional hearth which is at least 125mm thick with the minimum dimensions as shown in diagram.
16 5. FIRE SURROUND CLEARANCES If the appliance is to be fitted with a fire surround, use the minimum clearances shown in the diagram below between any point of the appliance and any combustible material. Yeoman produce a selection of surrounds and details can be obtained from your local supplier.
17 2.7 Ventilation requirements in the UK are as shown in the table below: A) Traditionally Built Homes •Where theleakage isgreater than5m 3 /hour/m 2 .
18 2.11 Extractor fans or cooker hoods must not be placed in the same room or space as this can cause the appliance to emit fumes into the room. 2.12 Increase air supply provisions where a room contains multiple appliances. 2.13 If any checks reveal problems do not proceed with the fitting of the appliance until they have been rectified.
19 LEGAL REQUIREMENTS Before installation and/or use of this appliance please read these instructions carefully to ensure that all requirements are fully understood. The appliance must be fitted by a registered installer * , or approved by your local building control officer.
20 INSTALLATION INSTRUCTIONS 2. REMOVAL OF THE DOOR 2.1 To remove the door: — Using a 5mm A/F Hey Key remove the door by opening, removing the 4 bolts and lifting the door free of the appliance body. PR7084 4 Bolts 3. REMOVAL OF THE LOG GUARD 3.1 To remove the log guard: — Lift log guard clear of the supporting brackets.
21 INSTALLATION INSTRUCTIONS 4.4 To remove the baffle: — Open door. — Lift the front edge of the baffle to clear the support bars. — Pull the baffle forward to disengage the rear edge from the location above the secondary air inlet holes. — Rotate the baffle and remove through the door opening.
22 INSTALLATION INSTRUCTIONS 6. REMOVAL OF CLEANBURN CHAMBER 10 PR9045 Cap head screws 6.1 Remove the 4 M6 x 25 cap head screws using 5mm hexagonal key. 6.2 Lift chamber, rotate forward and remove from stove. 6.3 Check rope seal is in good condition (see Diagram 11).
23 COMMISSIONING 1.1 To commission: — Replace the baffle and log guard. — Check the door alignment and catch operation and adjust if required (see Maintenance & Servicing, Section 8 ). — Check the soundness of door seals, castings and joints.
24 MAINTENANCE and SERVICING For a complete list of spare parts and accessories contact your Yeoman retailer or call 01392 474011 1. ANNUAL SERVICE 1.1 Before the start of the heating season strip, inspect and clean the appliance as detailed: — Allow appliance to cool.
25 2. REMOVAL OF THE LOG GUARD 2.1 To remove the log guard: — Lift log guard clear of the supporting brackets. — Rotate to clear the sides of the door opening. Do not use appliance without the log guard in position. 3. FITTING AND REMOVAL OF BAFFLE 3.
26 PR8739 Glass rope seal B Black face — Place the glass into position in the door. — Place the glass clamp into position. — Re-fix with the clean fixing screws. — Tighten the screws evenly until the clamp holds the glass. 6.2 Fitting the door is the reverse of the process detailed in Installation Section 2, Page 20.
27 8. ADJUSTING DOOR CATCH & HINGES 8.1 To maintain the safe use of your appliance, you may need to adjust the door hinges to ensure the door closes safely and correctly. 8.2 To adjust the door hinge plate assembly : — Open door and lift free of hinge plate.
28 SPARE PARTS R ef. No. Product Code Dra wing No. (if different) Descr iption 1 CA7660 CANOPY 2 ME600486 MESH 3 STMB-MEC8609 MEC8609 AIR W ASH DUCT ASSEMBL Y 4 RA502311 CLAMP 5 M08200STUD M08 x 200 S.
29 R ef. No. Product Code Dra wing No. (if different) Descr iption 1 CA7638 OUTER DOOR 2 - MEC600455 DOOR HANDLE STOP RING 3 MEC8619 DOOR HANDLE ASSEMBL Y 4 F A500025 T ORSION SPRING 5 F A9508 F A500016 SPRING 6.
SERVICE RECORDS 30 1ST SERVICE Date of Service:........................................................................... Next Service Due:....................................................................... Signed:................................
31.
Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LF Tel: (01392) 474011 Fax: (01392) 219932 E-mail: info@stovax.com www.stovax.
デバイスYeoman CL MILNER BRICK YMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yeoman CL MILNER BRICK YMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYeoman CL MILNER BRICK YMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yeoman CL MILNER BRICK YMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yeoman CL MILNER BRICK YMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yeoman CL MILNER BRICK YMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYeoman CL MILNER BRICK YMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yeoman CL MILNER BRICK YMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYeoman CL MILNER BRICK YMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。