ZanussiメーカーZGG66424BAの使用説明書/サービス説明書
ページ先へ移動 of 16
EN User manual Hob ZGG66424 IE GB.
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.
and that it is centrally positioned on the rings in order to avoid safety risks. • Do not use unstable cook ware or cookware with damaged bottom. There is a risk of tilt- ing and accident.
• Disconnect the appliance from the elec- trical supply, before you do the mainte- nance work or you clean it. • The electrical mains terminal is live. • Make electrical mains terminal free of volt- age. • Install correctly to give anti-shock protection.
edges of the hob is 400 mm. If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. For appliances installed in the Republic of Ire- land please refer to NSAI- Domestic Gas In- stallation I.S 813 Current Ed ition Section 7- Permitted Locations of Appliance.
4. With a thin screwdriver, adjust the by-pass screw position. 1 1 The by-pass screw – If you change from natural gas G20 20 mbar to liquid gas, fully tighten the by- pass screw in. – If you change from liquid gas to natural gas G20 20 mbar, undo the by-pass screw approximately 1/4 of a turn (1/2 of a turn for Triple Crown burner).
1 2 3 4 5 1 Green and Yellow 2 3 amp fuse 3 Brown 4 Cord clamp 5 Blue Should the plug need to be replaced for any reason, the wires in the mains lead are coloured in accordance with the following code: Green and yellow - Earth Blue - Neutral Brown - Live 1.
min 20 mm (max 150 mm) 30 mm 60 mm b a a) Removable panel b) Space for connec tions Kitchen unit with oven The hob recess dimensions must obey the indi- cation and the kitchen unit must be equipped with vents to let a continuous supply of air.
2. Keep the control kn ob pushed for approxi- mately 5 seconds; this will let thermocou- ple to warm up. If not, the gas supply will be interrupted. 3. Adjust the flame after it is regular. If after some tries the burner does not light, check if the crown and its cap are in correct positions.
Burner Diameters of cookware Rear Semi-rap- id 120 - 220 mm Auxiliary 80 - 160 mm Warning! Pots must not enter the control zone. Flame will heat up the control zone.
The stainless steel can become tarnished if it is too much heated. Refer to this you must not cook with potstones, earthenware pans or cast iron plates. Do not use aluminium foil to prevent damage the top during operation. Removing the dirt: 1. – Remove immediately: melting plastic, plastic foil, and food containing sugar.
If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, speak your dealer or the local Service Force Centre.
Electric supply: 230 V ~ 50 H z 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Gas connecti on: G 1/2 " Category: II2H3+ Gas supply: G20 (2H) 20 mbar Appliance .
14 www.zanussi.com.
15 www.zanussi.com.
www.zanussi.com/shop 397225902-A-112012.
デバイスZanussi ZGG66424BAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zanussi ZGG66424BAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZanussi ZGG66424BAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zanussi ZGG66424BAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zanussi ZGG66424BAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zanussi ZGG66424BAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZanussi ZGG66424BAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zanussi ZGG66424BAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZanussi ZGG66424BAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。