ZenoahメーカーBC251の使用説明書/サービス説明書
ページ先へ移動 of 16
GB-1 G B BC251 BC251 G B OWNER’S MANUAL BRUSHCUTTER 848JBZ93A1 (704).
GB-2 BC251 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS SOUND LEVEL VIBRA TION LEVEL ISO 22868 : 2005 LwA measured guaranteed ISO 22867 : 2004 racing MODEL LpA EN27917 idling BC251 25.4 cm 3 101.5 dB(A) 114.9 dB(A) 116 dB(A) 4.1 m/s 2 7.8 m/s 2 DECLARA TION OF COMFORMITY The undersigned manufacturer ZENOAH CO.
GB-3 G B BC251 1. Par ts location SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury , and for this reason you are requested to read all such instructions carefully and follow them without fail.
GB-4 BC251 2. Specification 4. Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. Accor ding to these indications, please be careful not to make a mistake. The port to refuel the “MIX GASOLINE” Model BC251 Overall size (LxWxH) mm 1810 x 330 x 390 Dry weight kg 5.
GB-5 G B BC251 b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be diffi- cult to gain a clear view of the working area.
GB-6 BC251 onto the ground in a flat clear ar ea and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts. W ARNING Never place the throttle into the high-speed position when starting the engine.
GB-7 G B BC251 6. Never touch the muffler , spark plug, or other metallic parts of the engine while the engine is in op- eration or immediately after shut- ting down the engine. Doing so could result in serious burns or electrical shock. • IF SOMEONE COMES 1.
GB-8 BC251 6. Set up INST ALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (1) INST ALLING CUTTING A TT ACHMENT GUARD • Attach the cutting attachiment guard with the bolts provided while inserting the spacer between the guard and the pipe.
GB-9 G B BC251 ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 <when using ZENOAH genuine oil> • Exhaust emission are controlled by the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the intro- duction of an inert material during combustion.
GB-10 BC251 W ARNING • The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position.
GB-11 G B BC251 ADJUSTING IDLING SPEED (1) 1. When the engine tends to stop frequently at idling mode, turn the adjusting screw clockwise. 2. When the cutting head keeps rotating after r eleasing the trigger , tur n the adjusting screw counter -clockwise.
GB-12 BC251 8. Operation CUTTING WORK (LINE HEAD USAGE) W ARNING 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury .
GB-13 G B BC251 9. Maintenance Every Every Ever y 25 50 100 System/components Procedure Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter.
GB-14 BC251 IMPORT ANT • Note that using any spark plug other than those des- ignated may result in the engine failing to operate prop- erly or in the engine becoming overheated and dam- aged. • To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench.
GB-15 G B BC251 GEAR CASE • The reduction gears ar e lubricated by multipurpose, lithium-based grease in the gear case. Supply new grease every 25 hours of use or mor e often depend- ing on the job condition. • Remove the bolt of the grease nipple and the bolt opposite side of the grease nipple.
GB-16 BC251 Limited warranty Should any failure occur on the pr oduct under nor mal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer .
デバイスZenoah BC251の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zenoah BC251をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZenoah BC251の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zenoah BC251の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zenoah BC251で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zenoah BC251を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZenoah BC251の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zenoah BC251に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZenoah BC251デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。