ZenoahメーカーBK4310FLの使用説明書/サービス説明書
ページ先へ移動 of 20
BK3410FL BK4310FL BRUSHCUTTERS 848-KD6-93A1 (806) OWNER’S MANUAL •B efore using our brushcutter, please read this manual carefully to understand the proper use of your unit.
2 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
3 1. WARNING LABELS ON THE MACHINE (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) Keep all children, bystanders and helper.
4 ■ BEFORE USING THE MACHINE a. Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in cutting grass, and it should never be used for any other purpose .
5 ■ WORKING GEAR AND CLOTHING a. When using your brushcutter, you should wear proper clothing and protective equipment as follows. (1) Helmet (2) Protection goggles or face protector (3) Thick work gloves (4) Non-slip-sole work boots (5) Ear protectors b.
6 ■ THINGS TO CHECK BEFORE USING YOUR BRUSHCUTTER a. Before beginning work, look around carefully to get a feel for the shape of the land, or grass to be trimmed, and whether or not there are any obstacles which might get in the way while working, and remove any obstacles which can be cleared away.
7 ■ KICKBACK SAFETY PRECAUTIONS •A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury.
8 immediately after shutting down the engine. Doing so may result in serious burns. i. When you finish cutting in one location and wish to continue work in another spot, turn off the engine and turn the unit as the blade faces away from your body. ■ MAINTENANCE SAFETY PRECAUTION a.
9 ■ ATTACHING THE SHOULDER STRAP (SE1) 1. Pass the ring of the shoulder strap through the hook(A) and fix it by the bolt securely. 2. Set the hook(B) of each shoulder strap to the D-rings on the frame. (A) UPPER SIDE (B) LOWER SIDE (1) Hook (A) (2) Bolt (M5x12) (3) Hook (B) (4) D-ring ■ ATTACHING THE LINER 1.
10 try inserting it again. • Once the liner has been inserted, pull on the liner to make sure that the stopper is properly engaged. ■ ATTACHING THE THROTTLE CABLE After fitting the wire, check if the wire sleeve is correctly fitted to the wire stopper.
11 ■ ADJUSTING THROTTLE CABLE • Proper play of the throttle cable is 1–2mm. Place the throttle lever to the lowest speed position (i.e. fully released status). Pull the throttle cable lightly with fingers to check its play. Readjust the position of cable adjuster if the play is too large or too small.
12 ■ BLADE •N ever attach nor remove a cutting blade while the engine is running. • Use ZENOAH genuine cutting blade for exchange. • Wear sturdy gloves for attaching/removing a metallic cutting blade to avoid injury. 1. Loosen the nut, remove holder A and holder B from the gear case.
13 5. Fuel • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. •W ipe up all spills before starting the engine. •M ake sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored.
14 6. OPERATION ■ STARTING THE ENGINE 1. Pour the fuel and fasten the fuel cap. (OP1) (1) Cap (2) Fuel tank • Make sure that the cap is firmly shut and there is no fuel leak. • Wipe out the spilled fuel. 2. Open the fuel cock. (OP2) 3. Move the choke lever to the closed position.
15 ■ STOPPING THE ENGINE 1. Return the throttle lever to the idling position. 2. Push the engine switch button. (OP5) 3. Close the fuel cock. (1) Engine switch button ■ EQUIPPING THE SHOULDER STRAP (OP6) 1. Hold the main pipe with your right hand.
16 6. OPERATION LINE HEAD USAGE • Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction.
17 ■ BLADE • Sharpen each cutting edge and make sure the bottom corner is rounded. (MA1) • Do not cool the blade with water in case of using grinder. It may cause cracks on blade. ■ REFILLING TRIMMING LINE (MA2) 1. For replacement line, use a diameter of .
18 7. MAINTENANCE ■ GEAR CASE • Remove cutter, cutter holder A and plug and insert fresh lubricant. (MA4) (1) Holder A (2) Plug ■ FUEL STRAINER Drain the fuel from the tank. Remove the fuel strainer from the fuel tank and clean the fuel strainer.
■ FLEXIBLE SHAFT (MA8) 1. While pulling the stopper of the clutch housing upward, remove the liner from the unit. 2. Remove the flexible shaft from the liner, apply lubricant to the shaft, and insert the shaft back into the liner. (1) Stopper (2) Liner ■ MUFFLER 1.
10. SPECIFICATIONS ZENOAH Knapsack Brushcutter Name/Type BK3410FL BK4310FL Handle Type Loop Machine Weight ( ✽ 1) kg 8.8 9.0 Outward Size (L x W x H) mm 315 x 270 x 410 Outer pipe mm 1500 (ø26) App.
デバイスZenoah BK4310FLの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zenoah BK4310FLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZenoah BK4310FLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zenoah BK4310FLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zenoah BK4310FLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zenoah BK4310FLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZenoah BK4310FLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zenoah BK4310FLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZenoah BK4310FLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。