ZenoahメーカーBKZ5000DLの使用説明書/サービス説明書
ページ先へ移動 of 16
GB-1 G B BKZ4500DL / BKZ5000DL BKZ4500DL BKZ5000DL G B OWNER’S MANUAL BRUSHCUTTERS 848KH093A3 (704).
GB-2 BKZ4500DL / BKZ5000DL EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS SOUND LEVEL VIBRA TION LEVEL ISO 10884 LwA measured guaranteed ISO 7916 racing MODEL LpA EN27917 idling BKZ4500DL 45.2 cm 3 99 dB(A) 117 dB(A) 118 dB(A) 0.8 m/s 2 7.2 m/s 2 BKZ5000DL 50.
GB-3 G B BKZ4500DL / BKZ5000DL 1. Par ts location (1) Primer (2) Air cleaner cov er (3) Choke le ver (4) Fuel tank (5) Star ter knob (6) Blade (7) Angle transmission (8) Cutting Attachment guard (9) L.
GB-4 BKZ4500DL / BKZ5000DL 2. Specification 4. Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. Accor ding to these indications, please be careful not to make a mistake.
GB-5 G B BKZ4500DL / BKZ5000DL 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise.
GB-6 BKZ4500DL / BKZ5000DL BEFORE ST ARTING THE ENGINE 1. The area within a perimeter of 15 m (50 ft) of the person using the product should be consider ed a haz- ardous ar ea into which no one should enter . If necessary , yellow warning r ope, warning signs should be placed around the perimeter of the ar ea.
GB-7 G B BKZ4500DL / BKZ5000DL • IF SOMEONE COMES 1. Guard against hazar dous situa- tions at all times. W arn adults to keep pets and children away fr om the area.
GB-8 BKZ4500DL / BKZ5000DL 6. Set up INST ALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that the edge of CE label is matched with the handle. W ARNING • Stop tightening the screws when the gap A be- comes zero. FLEXIBLE SHAFT 1.
GB-9 G B BKZ4500DL / BKZ5000DL 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container . 3. Pour in all of the oil and agitate well. 4. Pour in the rest of gasoline and agitate again for at least one minute.
GB-10 BKZ4500DL / BKZ5000DL ST ARTING ENGINE W ARNING • The cutting head will start rotating upon the en- gine starts. 1. Feed fuel into the fuel tank and tighten the cap se- curely .
GB-11 G B BKZ4500DL / BKZ5000DL MET AL BLADE USAGE 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fas- tened according to instruction and the blade turns smoothly without abnormal noise.
GB-12 BKZ4500DL / BKZ5000DL d. Keep the blade sharp. A dull blade increase the chance of bounce. e. A void feeding the blade too rapidly . The blade can bounce away from material being cut if the blade is fed faster than its cutting capability . f. Cut only from your right to your left.
GB-13 G B BKZ4500DL / BKZ5000DL 8. Operation 9. Maintenance Every Every Ever y 25 50 100 System/components Procedur e Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe.
GB-14 BKZ4500DL / BKZ5000DL AIR FIL TER •T he air filter , if clogged, will reduce the engine per - formance. Check and clean the paper element by air blow as requir ed. If the element becomes dirty , re- place with a new one. (1) FUEL FIL TER • When the engine runs short of fuel supply , check the fuel cap and the fuel filter for blockage.
GB-15 G B BKZ4500DL / BKZ5000DL fler to become overheated and that in turn could cause the engine to catch on fire. Alwa ys make sure that the muffler is c lean and free of w ood c hips, lea ves, and other waste before use.
GB-16 BKZ4500DL / BKZ5000DL Limited warranty Should any failure occur on the pr oduct under normal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer .
デバイスZenoah BKZ5000DLの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zenoah BKZ5000DLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZenoah BKZ5000DLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zenoah BKZ5000DLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zenoah BKZ5000DLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zenoah BKZ5000DLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZenoah BKZ5000DLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zenoah BKZ5000DLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZenoah BKZ5000DLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。