ZenoahメーカーTR2001の使用説明書/サービス説明書
ページ先へ移動 of 16
GB-1 G B TR2001 BC2002 G B OWNER’S MANUAL BRUSHCUTTERS 848J6093A0 (311).
GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS W ARNING!!! RISK OF D AMA GING HEARING IN NORMAL CONDITIONS OF USE, THIS MACHINE MA Y INVOL VE A DAIL Y LEVEL OF PERSONAL EXPOSURE TO NOISE FOR THE OPERA TOR EQUAL TO OR GREA TER THAN 85 dB(A) MODEL 21.
GB-3 G B SAFETY FIRST Instructions contained in warnings within this manual mar ked with a symbol concern cr itical points which must be taken into consideration to pre vent possible serious bodily injury , and f or this reason y ou are requested to read all such instructions carefully and follo w them without fail.
GB-4 1. Par ts location 2. Specification Overall size (L W H) ............................ 1795 x 230 x 303 / 1795 x 340 x 303 mm Dry weight .................................................................................................. 4.1 / 4.
GB-5 G B 3. W ar ning labels on the machine 4. Symbols on the machine Read owner’ s manual before operat- ing this machine. W ear head, eye and ear protection. W arning / Attention K eep all children, bystander s and helpers 15 meters awa y from the machine.
GB-6 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise.
GB-7 G B 5. For safe operation part nor the throttle come into contact with any obstacle when the engine starts. W ARNING Never place the thr ottle into the high-speed position when starting the engine.
GB-8 could result in serious burns or elec- trical shock. • IF SOMEONE COMES 1. Guard against hazar dous situa- tions at all times. W arn adults to keep pets and children away fr om the area. Be car eful if you ar e ap- proached. Injury may result fr om flying debris.
GB-9 G B INST ALLING HANDLE • Install the handle to the shaft tube and clamp. INST ALLING DEBRIS GUARD • Attach the guard to the bracket on the main pipe and fix it with 2 screws.
GB-10 ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 • Exhaust emission are controlled b y the funda- mental engine parameters and components (eq., carburation, ignition timing and por t timing) with- out addition of an y major hardware or the intr o- duction of an inert material during combustion.
GB-11 G B ST ARTING ENGINE W ARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap se- curely . 2. Rest the unit on a flat, firm place. Keep the cutting head off the gr ound and clear of surrounding objects, as it will start rotating upon starting of the engine.
GB-12 TRIMMING GRASS AND WEEDS • Always remember that the TIP of the line does cut- ting. Y ou will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the gr ound and is tilted about 20 degrees towar d the sweep direction.
GB-13 G B Every Every Ever y 25 50 100 System/components Procedur e Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter , fuel filter inspect/clean ✔✔ r eplace, if necessary see adjusting replace carbur etor idle adjusting screw ✔ idling speed (p.
GB-14 SP ARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a r e- placement plug, use the correct type specified by KOMA TSU ZENOAH. • REPLA CEMENT PLUG IS A NGK BPMR7A.
GB-15 G B 3. T ake out the spool and pull off the old line. Put one end of new line through the spool holes and pull it until the length is equal between each part of the line. 4. Wind up the line in the correct dir ection as indicated on the spool. 5.
GB-16 11. T r oubleshooting guide Case 1. Starting failure CHECK PROB ABLE CAUSES A CTION fuel tank → incorrect fuel → drain it and use correct fuel fuel filter → fuel filter is clogged → clea.
デバイスZenoah TR2001の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zenoah TR2001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZenoah TR2001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zenoah TR2001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zenoah TR2001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zenoah TR2001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZenoah TR2001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zenoah TR2001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZenoah TR2001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。