ZyXEL Communicationsメーカー1111の使用説明書/サービス説明書
ページ先へ移動 of 22
www .zyxel.com www .zyxel.com User ’ s Guide Z-W ave Series S H D 111 0 / 1111 / 2 11 0 / 3 11 0 Copyright © 201 1 ZyXEL Communications Corporation Edition 1, 7/2011.
.
About This User's Guide Z-Wave Series Programming Guide 3 About This User's Guide Intended Audience This manual is intended for people who want to configure the Z -W av e Series products. Related Document ation •Q u i c k S t a r t G u i d e The Quick Start Guide is designed to help y ou get up and running right aw ay .
Safety Warnings Z-Wave Series Programming Guide 4 Safety Warnings • Do not dispose of electrical applianc es as unsorted municipal waste, use separate collection faciliti es. • Contact your local gov ernment for informatio n regarding the collection sys tem s available.
Table of Contents Z-Wave Series Programming Guide 5 Table of Contents About This User's Guide ................................................................................. ....................... .. 3 Document Conventions ....................
Table of Contents Z-Wave Series Programming Guide 6 4.2.2 Grouping 2 .......... ... .... ... ... ... .... ... ... ... ............. ... .... ... ... ... .... ... ... ... ............. ... .... ... ... ... .... 18 4.2.3 Z-Wave’ s Configuration ......
Z-Wave Series Programming Guide 7 C HAPTER 1 The Z-Wave Series 1.1 Overview This User’s Guide provides progr amming methods for the Z -W ave Controller which controls each Z - W ave Series device and unifies them into a Z -W ave network to control y our home electronics.
Z-Wave Series Programming Guide 8 C HAPTER 2 SHD1110 Programming 2.1 Z-W ave Group s (Associat ion Command Class V ersion 2) On the Z -W ave Controller , you can set the SHD1110 to send reports of its.
Chapter 2 SHD1110 Programming Z-Wave Series Programming Guide 9 T emperature (Celsius) The following parameters are used in this example: Sensor V alue 1 = 0x01 Sensor V alue 2 = 0x31 T emperature (C)= (Sensor V alue 1*2 56 + Sensor Value 2)/10 = (1*256+49)/10 = 30.
Chapter 2 SHD1110 Programming Z-Wave Series Programming Guide 10 When the SHD1110 is triggered, it will send out BASIC_SET_COMMAND to the nodes of Grouping 2. R efer to the Z- W av e’ s Configuration section to configuration par ameter 1 for the setting of basic set command.
Chapter 2 SHD1110 Programming Z-Wave Series Programming Guide 11 Note: Once the SHD1110 is reset, it wi ll be restored to its factory default status and settings. 2.1.4 Auto Report 2.1.4.1 Time Interval Y ou can set the SHD1110 to automatically send out reports of its current status to Grouping 1 at a set time.
Chapter 2 SHD1110 Programming Z-Wave Series Programming Guide 12 2.1.5 W akeup Configuration The SHD1110 stays in sleep status for the majority of time in order to conserve battery power . However , it can be waken up by either triggers of temper ature/humidit y or set time for the Z - W ave Controller to enable further settings.
Z-Wave Series Programming Guide 13 C HAPTER 3 SHD1111 Programming 3.1 Z-W ave Group (Associat ion Command Class V er sion 2) The SHD1111 supports one association group with fi ve nodes. When the SHD1111 is triggered, all devices associated with the SHD1111 will receive the relevant reports.
Chapter 3 SHD1111 Programming Z-Wave Series Programming Guide 14 0: OFF 1-99: ON (Binary S witch Device) Dim Level (Multilevel Switch Device) 3.1.3.2 Configur ing the OFF Delay Configuration P ar ameter #2 can adjust the time of delay before the OFF command is transmitted.
Chapter 3 SHD1111 Programming Z-Wave Series Programming Guide 15 3.2.3 Command Classes The SHD1111 supports the following Command Classes: • COMMAND_CLASS_SENSOR_BINARY • COMMAND_CLASS_BASIC • C.
Z-Wave Series Programming Guide 16 C HAPTER 4 SHD2110/3110 Programming 4.1 Basic Command Class / Bi nary Switch Command Cl ass The SHD2110/3110 responds to BASIC and BINARY commands of the Z- W ave system.
Chapter 4 SHD2110/3 110 Programmi ng Z-Wave Series Programming Guide 17 4.2 Z-W ave Group s (Associat ion Command Class V ersion 2) On the Z- W ave Controller , you can set the SHD2110/3110 to send it.
Chapter 4 SHD2110/31 10 Programming Z-Wave Series Programming Guide 18 4.2.1.4 Meter Report Command The SHD2110/3110 will report its instant powe r consumption to Grouping 1. For detailed description of meter report command, refer to page 4. 4.2.2 Grouping 2 Grouping 2 includes the BASIC_SET commands.
Chapter 4 SHD2110/3 110 Programmi ng Z-Wave Series Programming Guide 19 4.2.3.3 Meter Report Perio d (SHD31 10 only) If the Meter Report is set to 30 second s , the SHD2110/3110 will report its instant power consumption Z -W ave Controller in every 30 seconds.
Chapter 4 SHD2110/31 10 Programming Z-Wave Series Programming Guide 20 Accumulated power consumption (KW/h) = (Meter V alue 2*65536) + (Meter V alue 3*256) + (Meter V alue 4) = 70.
Z-Wave Series Programming Guide 21 A PPENDIX A Legal Information Copyright Copyright © 2011 by Z yXEL Communications Corporation. The contents of this publication may not be repr oduced in any part o.
Appendix A Legal Information Z-Wave Series Programming Guide 22 Notices Changes or modifications not expressly approved by the part y responsible for compliance could void the user's authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.
デバイスZyXEL Communications 1111の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ZyXEL Communications 1111をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZyXEL Communications 1111の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ZyXEL Communications 1111の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ZyXEL Communications 1111で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ZyXEL Communications 1111を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZyXEL Communications 1111の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ZyXEL Communications 1111に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZyXEL Communications 1111デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。